Technical Specifications - Yamaha Nexo NXAMP4X4 User Manual

TECHNICAL SPECIFICATIONS

POWER SPECIFICATIONS FOR NXAMP Powered TDcontroller
Number of channels
Max. output power (8 Ω)
Max. output power (4 Ω)
Max. output power (2 Ω)
Power consumption
SPECIFICATIONS FROM ANALOG IN TO POWER OUT
Analog Inputs channels
Frequency response
Input Impedance
Max Input Level
Dynamic Range
THD + Noise
Latency time
Power Supply
FRONT AND BACK PANEL FEATURES
Audio Inputs
Power Outputs
RS232 port
GPIO port
Front Panel
Rear Panel
Dimensions & Weight
USER CONTROLS
System Selection
System Set-up
Protection
Delay
Input Patching
Output Gain
Volume control
Save/Recall
Array EQ
Security Mode
Remote control
Certification
Green status
TECHNICAL SPECIFICATIONS
4 channels, 3 channels (2 non bridged + 1 bridged) or 2 channels (2 bridged)
NXAMP4X1
600 W (non bridged)
1800 W (2 channels bridged)
900 W (non bridged)
2600 W (2 channels bridged mode)
1300 W (non bridged)
10 W Standby, 100 W Idle, 1100 W 1/8 Power 20 W Standby, 150 W Idle, 3000 W 1/8 Power
4 channels analog inputs on XLR 3 with a second XLR 3 for linking
+/- 0.5 dB from 10 Hz to 20 KHz
20 KOhm.
+28 dBu
All Channels = 105dB unweighted
Typical 0.1% flat setup
2.2 ms on a flat setup (Compatible with NX241 and NX242)
Dedicated version for 100 ~ 120 Volts or 220 ~ 240 Volts
• 4 balanced analog inputs on XLR with link, using 24 bit converters.
• 4 digital inputs via the optional network card slot at the back.
4 Speakon outputs
Allow firmware upgrade for software improvement and new cabinet setups.
5 Global Purpose Inputs and 8 Global Purpose Outputs
On/Off switch, Wheel, A/B buttons, 40 char x 2 display. Amp protect/Stand-by/Power LED's.
For each ch: volume (15 LEDs), Mute w LED, Output current LED, Protect LED, Peak LED.
1 mains socket (2 for NXAMP4X4); RS232; GPIO, Expansion slot, 4 XLR w link, 4 Speakon 4
NXAMP4X1
3U 19" Rack, 457 mm (18") Depth, 16.5kg
(33 lbs) net
Allows control from all NEXO ranges.
Within the selected range when possible, allows the cabinet to be set for passive/active mode,
wideband/crossover mode, choose among crossover point, cardiod/supercardiod mode.
Multiple Peak Limiters fitted for both selected cabinet and amplifier. Multiple Acceleration,
Displacement and Temperature protections on every channel.
Up to 66m (145 ft.) of delay in 10cm (.4in ) steps
Any of the 4 analog (or 8) inputs combination to be routed on each output.
Global and inter-channel gain +/-6dB in 0.5dB steps.
Each channel with 16 steps from – inf dB to 0 dB.
Set-up Stores 32 user set-ups
LF/HF shelving filters to compensate ground/stacking effects, +/-6dB
Password protected for Read-Only or Remote-Only Mode.
Full remote control via the Ethersound protocol and ESmonitor software.
UL, SEMKO (CE), CCC, KOREA, TSS, PSE
Compliant with ROHS and WEEE directive
NXAMP4X4
1900 W (non bridged)
6600 W (2 channels bridged)
3300 W (non bridged)
8000 W (2 channels bridged)
4000 W (non bridged)
NXAMP4X4
4U 19" Rack, 457 mm (18") Depth, 24.5kg
(33 lbs) net
PAGE 80 OF 91