FUNAI WD6D-D4413DB Owner's Manual page 74

Symptom
No image from HDMI connection.
TV channels cannot be changed.
Some settings are lost even though you
followed the procedure correctly.
Only specific channels do not appear.
Though auto tuning was completed,
you cannot watch the DVB and
analogue channels.
The TV channel which you have been
able to watch before has disappeared
and "No signal" is displayed.
The image from the external device
cannot be displayed.
Recording is impossible.
Timer recording cannot be
performed.
"Repairing" appears on the TV
screen.
Repairing
In a case you intend to cancel the
repairing process.
Do you want to cancel a repairing
process? When selecting "Yes",
the disc may not be usable.
Yes
No
Repairing
The indication
"
Writing to Disc
does not disappear.
Recording does not start
immediately after pressing [REC].
74
EN
• Check the HDMI connection. (Check the status of the HDMI related indications.)
• Check whether the connected monitor device or other device supports HDCP.
(This unit will not output a video signal unless the other device supports HDCP.)
• Check the setting of HDMI.
• Check whether the output format of this unit (HDMI FORMAT) matches the
supported input format of other connected device.
• If the unit is connected to the unauthorised display device with an HDMI cable,
the audio and video signals may not be output when playing back a commercial
DVD-video.
• Check if the connections are made securely and correctly.
• Check if the cables are damaged.
• Try "Channel" setting by following the steps on pages 21-23.
• If you unplug the AC mains cable while the warning message, "Saving settings.
Please wait.", is displayed, some settings may be lost. Do not unplug the AC
mains cable while the message is displayed (It will take about 1 minute.).
• The channels may be set to be skipped. (See pages 22, 25.)
• Confirm whether an antenna cable is connected correctly and try to tune again.
(See pages 21-23.)
• If you move the unit to a different area, you will need to perform auto tuning
again.
• Try pressing [INPUT SELECT] repeatedly to select the external input channel,
then press [PROG.
• Turn on all connected devices.
• Check if the connections are made securely and correctly.
• This unit cannot record programmes that contain copy protection signal. This is
not a malfunction.
• The space of the recording media may be used up. Try deleting unnecessary
titles, or exchange it with the recordable media.
• The maximum number of titles or chapters has exceeded. Delete the
unnecessary titles to make enough space or insert a new recordable media.
• Check if the disc is CPRM compatible. Copy-once programmes can only be
copied onto the disc which is CPRM compatible.
• Check if the disc is protected or finalised. Undo the protection or the finalisation.
• Video mode DVD-RW once formatted in other unit cannot be recorded in this
unit unless formatted in this unit.
• Check if the connections are made securely and correctly.
• The internal clock of the unit may have been stopped due to a power failure that
lasted for more than 30 seconds. Reset the clock. (See page 67.)
• If there is a power failure or unplugging during recording, finalising, formatting or
editing (even after "Repairing" disappears), a repairing process will begin
automatically just after turning the unit on again.
• It may take several minutes up to about several hours.
• If you intend to cancel the repairing process, press [OPEN CLOSE A] on the
front panel, then select "Yes" and press [ENTER OK]. After that, press
[OPEN CLOSE EJECT A] to take out the disc. The disc cancelled during the
repairing process MAY NOT work.
• "
Writing to Disc
" 20 seconds even after it reached 100%. This is not a malfunction.
100%
• Make sure the videotape has a recorded tab when you record to a videotape. If
needed, cover the hole with cellophane tape.
Remedy
] repeatedly to select your desired channel.
" may remain on screen for the maximum of
100%