Table of Contents
Advertisement
SETUP PROCEDURE USING AV NETWORK DEVICE CODES:
An AV Receiver Setup example is shown below. If your device is not listed or the device codes not work after following the setup
procedure, please refer to the AV NET Learning wizard procedure on pages 33-34.
1.
Press the A/V Net button on the remote control.
POWER
DVD
DVD2
VCR
VCR2
AV Receiver
Move
Select
SEL
2.
Use CURSOR PADS
or
3.
Press the SELECT button or CURSOR PADS
remote control and the device selection screen appears.
PV Recorder
Cable Box
Set Top Box
Custom
Device Setup
Move
Select
SEL
4.
Use the CURSOR PADS
and press the SELECT button on the remote control.
5.
The Setup button on the bottom of the screen becomes
highlighted. Press the SELECT button on the remote control
to enter the setup screen.
HITACHI AV NET SET UP
Please choose the device to set up.
( ) DVD
( ) Set Top Box
( ) DVD2
( ) DVD3 (Custom)
( ) VCR
( ) VCR3 (Custom)
( ) VCR2
( ) PVR2 (Custom)
( ) AV Receiver
( ) CBL2 (Custom)
( ) PV Recorder
( ) STB2 (Custom)
( ) Cable Box
List
BACK
SETUP
Move
SEL
Select
6.
Using the remote, enter the four digit Device Code for your
equipment, found on page 25.
7.
Use the CURSOR PAD
CURSOR PAD
or
to set the INPUT to which your
device is connected.
8.
Use the CURSOR PAD
Speakers to ON or OFF, then press SELECT to set the
option chosen.
9.
Press CURSOR PAD
the CURSOR PADS
or
softkeys, before pressing the SELECT button to perform a
Transmission Test of the softkey selected. If the device
responds, then it is properly set up. Select OK. (If the
Transmission Test failed, try another code).
HITACHI AV NET SET UP
AV Receiver
Device Code
- - - -
(Enter Code "9999" to uninstall)
AV Input
Input4
Internal Speakers
On
Off
Transmission Test
POWER
BACK
OK
Move
Input
0-9
MENU
HOME
to highlight Device Setup.
on the
or
to choose AV Receiver
MODIFY
to select AV Input. Press the
to select Internal Speakers.
to select Transmission Test. Press
to select Power, Play, or CH UP
PLAY
CH UP
EXIT
AV NETWORK SETUP WIZARD
10. If "OK" was selected, and the 4 digit code was invalid, the
screen below appears, then goes back to the Device
Code
entry screen.
ATTENTION
Find your AVR
4-digit manufacturers code
and enter it here
11. Repeat Device Setup procedure until the Source (SRC)
Setting Screen appears.
This screen allows you to assign a label for each Source (SRC1
to SRC8) connection on the AV Receiver. Depending on the
number of source connections to the AV Receiver, some sources
may not be available.
12. To label your sources, use CURSOR PAD
highlight SRC1.
13. Use CURSOR PAD
DVD2, VCR, VCR2, PVR, CBL, STB, TV or Custom). If
SRC1 is active, video and audio will be available depending
on the connections.
14. Repeat for SRC2 to SRC8 if applicable.
15. Select DONE to continue.
HITACHI AV NET SET UP
AV Receiver (SRC Setting)
SRC1
SRC1
SRC2
SRC2
SRC3
SRC3
SRC4
SRC4
SRC5
SRC5
SRC6
SRC6
SRC7
SRC7
SRC8
SRC8
BACK
DONE
Move
Set Input
SEL
16. Select CONTINUE to setup another device.
HITACHI AV NET SET UP
Congratulations!
Your AVR is now connected
to your AV network.
Would you like to set up
another device?
Done
Move
SEL
Select
17. Select DONE to finish and the screen below appears to
show the device(s) which has been set-up.
HITACHI AV NET SET UP
Device
Code
DVD
----
Not Setup
DVD2
----
Not Setup
VCR
----
Not Setup
VCR2
----
Not Setup
AVR
1360
Not Setup
PVR
----
Not Setup
CBL
----
Not Setup
STB
----
Not Setup
STB2
----
Not Setup
EXIT
Select
SEL
18. Select EXIT to quit.
24
or
to
or
to select the Source (DVD,
EXIT
IR Out
Continue
Video
Audio
Not Setup
Not Setup
Not Setup
Not Setup
Not Setup
Not Setup
Not Setup
Not Setup
Not Setup
Advertisement
Table of Contents
