Advertisement
Available languages
Available languages
Quick Links
Model SL-5680
READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION.
NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through
conduit or another acceptable means. Contact a qualified electrician if there is any question as to the suitability of
the system.
Lamp in Fixture Contains Mercury. Dispose According
to Local, State, or Federal Laws.
Photocontrol
(B)
Fluorescent
Lamp
© 2007 HeathCo LLC
Installation Instructions
Ground
Screw
(A)
Mounting Plate
Lens
No Service Parts Available for this Product
Fluorescent Outdoor
WARNING: Turn power off at the fuse or circuit
breaker.
1. Select a location on a flat wall with a properly attached electrical
junction box.
2. Unscrew the lens. Set aside the lens and fluorescent lamp.
3. Remove the decorative nut. Remove the mounting plate.
4. Thread the junction box wires through hole (A) in the mounting
plate.
5. Make sure the arrow on the mounting plate is pointed up. See
which pair of holes in the mounting plate will line up for your
junction box. Secure the mounting plate to the junction box. The
two #8-32 screws provided should work with round or octagon
junction boxes. If you are using a small rectangular box, you
will need to purchase two #6-32 screws at least 1/2" long.
6. Secure the service ground wire under the head of the green
ground screw.
7. Connect the fixture wires to the service wires (black to black
and white to white). Secure with wire nuts provided.
8. Make sure the wire nuts and wires are inside the fixture wiring
compartment. Secure the fixture body to the mounting plate
with decorative nut (B).
9. Plug in the 13 Watt fluorescent lamp provided.
10. Reinstall the Lens.
11. Caulk fixture mounting surface with silicone weather sealant.
To test operation during daylight, cover the photocontrol window
with black tape. Turn on the power. The photocontrol has a time
delay (up to 2 minutes) before it will respond to light changes. The
light will take up to five minutes to reach full brightness. Uncover
the photocontrol and your unit will operate automatically—on at
dusk, off at dawn.
Security Light
598-1100-02
Advertisement
Related Manuals for Heath Zenith SL-5680
Summary of Contents for Heath Zenith SL-5680
- Page 1 Model SL-5680 READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION. NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through conduit or another acceptable means. Contact a qualified electrician if there is any question as to the suitability of the system.
- Page 2 Modelo SL-5680 ANTES DE EMPEZAR LA INSTALACIÓN LEA CUIDADOSAMENTE TODAS LAS INSTRUCCIONES. NOTA: Todo el cableado debe realizarse de acuerdo con el Código Nacional Eléctrico (Código Eléctrico Canadiense en Canadá) usando tubería u otro medio aceptable. Contáctese con un electricista calificado si tiene alguna pregunta respecto a la adaptabilidad del sistema.
- Page 3 Modèle SL-5680 LIRE SOIGNEUSEMENT LES DIRECTIVES AVANT D’ENTREPRENDRE L’INSTALLATION. NOTE : Le câblage doit être conforme aux exigences du Code national del'électricité (Code Canadian de l'électricité au Ca- nada) et être installé dans des canalisations ou autres dispositifs acceptables. Si vous avez des doutes concernant la convenance du système, consultez un électricien reconnu.
- Page 4 TWO YEAR LIMITED WARRANTY This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state to state or province to province. For a period of two years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you.