Doors - Heat & Glo SL-350TRS-D Owner's Manual

D. Doors
It's very important to know what kind of a door and what kind
of fi nishing material is going to be used on the fi replace. The
table below shows the door models and the fi nishing mate-
rial thickness allowed. For an inside fi t there is an available
template to assist with sizing the fi nishing material.
UNITS AND
TEMPLATE PART #
FINISH MATERIAL
DOOR FIT
THICKNESS
Aero-28 Inside 4 inches Max.
Aero-32 Inside 4 inches Max.
Aero-36 Inside 4 inches Max.
Chad-28E Overlap 1 inch Max.
Chad-28E Inside 1-4 inches
Chad-32E Overlap 1 inch Max.
Chad-32E Inside 1-4 inches
Chad-36E Overlap 1 inch Max.
Chad-36E Inside 1-4 inches
Halston-28E Overlap 1 inch Max.
Halston-28E Inside 1-4 inches
Halston-32E Overlap 1 inch Max.
Halston-32E Inside 1-4 inches
Halston-36E Overlap 1 inch Max.
Halston-36E Inside 1-4 inches
Table 1. Finishing Clearances for Aero, Chad and Halston Fronts
FINISHING MATERIAL
4 IN. MAXIMUM THICKNESS
Stop fi nishing material fl ush with fi replace surround opening.
Figure 11.16 Aero Door
FRONT FACE OF FIREPLACE
DOOR
Finishing materials 1 inch maximum thick.
Stop fi nishing material fl ush with opening.
Figure 11.17 Overlap Fit Door (Chad and Halston)
48 Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev. D • 6/07
SL-350TRS-D (350-Template)
SL-550TRS-IPI-E (550-Template)
SL-750TRS-IPI-E (750-Template)
SEE
X
FIGURE
11.16 N/A
11.16 N/A
11.16 N/A
11.17 N/A
11.18 29-3/8 in. 28-3/8 in.
11.17 N/A
11.18 32-3/8 in. 30-3/8 in.
11.17 N/A
11.18 37-1/4 in.
11.17 N/A
11.19 29-3/8 in. 28-3/8 in.
11.17 N/A
11.19 32-3/8 in. 30-3/8 in.
11.17 N/A
11.19 37-1/4 in.
DOOR
FINISHING MATERIAL
4 IN. MAXIMUM THICKNESS
1 in. MAX
FINISHING MATERIAL
(TOP EDGE)
FINISHING MATERIAL
4 IN. MAXIMUM
THICKNESS
Y
N/A
N/A
N/A
N/A
N/A
N/A
34 in.
N/A
N/A
Finishing material between 1 and 4 inches thick.
N/A
Figure 11.18 Inside Fit Door (Chad)
34 in.
FINISHING
MATERIAL
Finishing material between 1 and 4 inches thick.
Refer to Table 1 for X and Y dimensions.
Figure 11.19 Operable Hinge Door (Halston)
DOOR
X
(Includes 1/8 in. opening each side of door)
Refer to Table 1 for X and Y dimensions.
*IF FINISHING MATERIAL IS THICKER THAN
2 IN., DOORS WILL ONLY OPEN
AS FAR AS PICTURED

DOORS

X
(Includes 1/8 in. opening each side of door)
FINISHING MATERIAL
4 IN. MAXIMUM
THICKNESS
Y
FINISHING
MATERIAL
Y