P4K;I - Denon POA-3012CI - Multi-Zone Audio Distribution Power Amplifier Owner's Manual

ENGLISH
Troubleshooting
12-channel driving, NORMAL operation:
30 W x 12 ch (8 (lJohms, DIN 1 kHz with 0.7 % TH.D.)
50W x 12 ch (4 (lJohms, DIN
1
kHz with 0.7 % TH.D.)
6-channel driving, BRIDGED operation:
100W x 6 ch (8 (lJohms, DIN 1 kHz with 0.7 % TH.D.I
0.05% (Rated output: -3 dB, 8 (lJohms, 1 kHz)
Speaker 4 - 16 (lJohms (NORMAL operation)
Speaker 8 - 16 (lJohms (BRIDGED operation I
550 mV /47 k(lJkohms (NORMAL operation)
275 mV /47 k(lJkohms (BRIDGED operationl
29 dB (NORMAL operation)
35 dB (BRIDGED operation)
5 Hz - 40 kHz (Low cut filter: OFF)
95 dB (input terminals short-circuited, with A-weightied network)
Cut off freguency 80 Hz (-12 dB/oct. Low cut filter: ON)
3-30VDC
12 V DC, 250 mA MAX
AC 120 V, 60 Hz (North America model) / AC 230 V. 50Hz (Europe model)
2.5 A (North America model) /230 W (Europe model)
Standby: 0.5 W or less
(When the "POWER CONFIGURATION" is set to "POWER BUTTON")
434 (W) x 171 (H) x 410 (D) mm (17-3/32" x 6-47/64" x 16-9/64")
19.0 kg (Approx 41 Ibs 14.2 oz)
Total harmonic distortion:
Output terminals:
Rated output:
Specifications
Gain:
Input sensitivity I Input impedance:
Frequency response:
SIN raito:
Low cut filter:
Trigger in level:
Trigger out level:
Power Supply:
Power Consumption:
Maximum external dimension:
Weight:
*
For purposes of improvement, specifications and design are subject to change without notice.
5
7
10
17
• Make sure the unit is correctly
plugged in and switched on at
the mains socket.
• Insure the correct input is
selected.
• Set to an appropriate level.
• Connect securely.
...•.. ". Cause
• The power supply cord's plug is
not fully plugged in.
• The speaker cables are not fully
connected.
• The device you want to listen to
has not been selected.
• The volume control is set to
minimum.
• The input cable is not fully • Connect securely. 7
connected.
• The speaker cable is not. Connect the speaker as 5
connected properly for the required for the Operation Mode
operation mode. (NORMAL MODE or BRIDGED
MODE)
• The input connector is not • Connect the input connector 7
connected properly. correctly (in the case of BRIDGED
input for each ZONE, input to an
even-numbered channel.)
• The "Turn On" command is not • Send the "Turn On" command 9, 14
input from the external terminal from the external device.
when the ZONE TRIGGER ON
MODE is set to ON LINE (the
ZONE operation mode indicator
is not lit).
• Trigger voltage is not input to • Input the trigger voltage from 9, 14
the TRIGGER IN terminal from the external device.
the external device when the
ZONE TRIGGER ON MODE is
set to "TRIG. IN':
Symptom
When the power is
turned on, the power
indicator does not
light and no sound
is produced.
The power indicator
lights but no sound
is produced.
Check the following before assuming there is a problem with the set:
1. Are all connections proper?
2. Is the set being operated as described in the owner's manual?
3. Are the speakers and input components being operated proper1y?
If the set does not seem to be operating properly, check the points listed below. If these points do not
apply, the set may be damaged. Turn off the power immediately and contact your store of purchase.
19