Table of Contents
Advertisement
AVR80 manual
11/01/98 13:01
On Screen Menus
In addition to the information shown on
the front panel display, it is also possible
to obtain the unit's current status
through the use of on screen video
messages. The on screen menus may also
be used to control many aspects of the
receiver and to make adjustments and
selections.
To activate the On Screen display system,
press the
SCREEN DISPLAY s
button on the remote. This will cause a
status summary display to be shown on
the screen for five seconds. (Figure #5).
Once the video displays are enabled, this
status screen will also appear when the
unit is turned on.
NOTE: In order to view the on screen
menu displays the receiver´s "S" Video
jack
must be connected to
TV Moni T
the standard, composite video input of a
TV monitor or projector. The on screen
displays are NOT visible via the "S" video
output
.
U
The status screen displays the following
information:
AUDIO SOURCE
currently selected for audio.
VIDEO SOURCE
currently selected for video.
: This is the source
TAPE1 OUT
currently routed to the Tape 1 audio
output for recording.
: This is the source
VCR1 OUT
currently routed to the VCR 1 video
output for recording.
Side 25
On Screen Display
: This is the currently selected
MODE
audio/surround mode.
MULTIROOM
currently selected for listening in
remote room locations.
MASTER VOLUME
current volume level. Note that
volume appears as a horizontal scale.
The "0dB" reference level is indicated
by a solid block
or exeeds it while volume levels below
the current level are indicated by
double vertical bars
Function Displays and Messages
Once the On Screen Displays have been
activated, they appear when certain
functions are performed from the front
panel buttons or the remote control.
These messages are three line displays
with the current function shown on the
top line and information about the
selection or choice on the bottom two
lines.
The following function/operation display
: This is the input
screens are available:
Surround Mode and Delay
: This is the input
When the surround mode is changed or
the delay timing is adjusted, this message
will appear at the bottom of the video
screen. The top line is the surround
mode, the bottom line is the delay time
for that mode. (Figure #6) Note that
delay time will not be displayed in the
MONAURAL
modes, as these modes do not
STEREO
have rear channel information.
25
Figure 5
: This is the source
: This is the
Í
, if volume catches
Figure 6
±
.
Figure 7
Figure 8
,
or
STEREO
DOLBY 3
Figure 9
A U D I O
S O U R C E
:
T U N E R
V I D E O
S O U R C E
:
V C R 2
T A P E 1
O U T
:
C D
V C R 1
O U T
:
A U X
M O D E
:
D O L B Y
P R O
L O G I C
M U L T I
R O O M : T U N E R
M A S T E R
V O L U M E
||
M O D E
: T H X
C I N E M A
D E L A Y
T I M E : 2 0 m s e c
< F U N C T I O N
S E L E C T >
A U D I O : T U N E R
V I D E O : V C R 1
< C O P Y
F U N C T I O N >
T A P E
O U T : T U N E R
V C R 1
O U T : V C R 2
F R O N T
L
:
+ 1
d B
F R O N T
R
:
2
d B
C E N T E R
:
+ 5
d B
S U R R O U N D
L
:
1 0
d B
S U R R O U N D
R
:
+ 3
d B
S U B
W O O F E R
:
0
d B
Hide quick links:
Advertisement
Table of Contents
