Remote Control Programming And Operation - Harman Kardon AVR80 Owner's Manual

Audio/video receiver
Hide thumbs Also See for AVR80:
Table of Contents

Advertisement

AVR80 manual
11/01/98 13:01
Another group of keys may only be
programmed with one remote code. The
code contained in these keys remains the
same regardless of the source selection.
WARNING: These keys transmit codes
that are vital to the operation of the
product. It is not recommended that they
be programmed with alternative codes, as
it may then be impossible to operate
certain functions of the receiver.
THX
Aux
Cursor Up
Pro Logic
Delay
Cursor Down
¤
Dolby 3 Stereo
Memo
Cursor Right ›
Movie
Screen Display
Cursor Left ‹
Matrix
Panel Display
Select
Hall
Speaker
Main Volume Up
Stereo
Test Noise
Main Volume Down
Mono
Adjust
Mute
RDS PTY
RDS AF
To program the remote, you need the
remote of the device, whose functions
shall be programmed. Note that it is not
necessary to program all keys, only those
Side 14
Remote Control Programming & Operation
that are required to operate the subject
device. Keys not programmed will retain
the codes preprogrammed at the factory.
1. Slide
Use/Learn a
left corner of the remote to the right so
that it is next to
2. If one of the multi-function buttons is
being programmed press the source
button (i.e.
have this function associated with. If you
are programming a single function key,
proceed to the next step.
3. Press the button on the remote that is
to be programmed. Note that the
Learning y
4. Place the remote head to head with the
remote control whose function is being
learned. The two remotes should be no
more than 8 inches apart.
5. Press and hold the button on the
transmitting remote corresponding to the
function to be memorized until the
Learning
LED goes out, release the button on the
transmitting remote. The function code
has been successfully captured.
NOTE: If both LEDs flash during a
programming operation, it indicates that
¤
the remote's memory is full or that the
remote codes from the transmitting
remote are not compatible with the unit's
signal format.
6. Continue to program any additional
remote commands required using steps 2
through 5. When you have finished
programming the remote, slide the
Use/Learn
in the
Use
14
switch at the top
.
Learn
,
, etc.) you wish to
CD
VCR
LED will illuminate.
LED starts to blink. When the
switch to the left so that it is
position.
Clearing the Remote Memory
In normal operation, codes for a new
device may be programmed "over" the
codes that have been previously
programmed into the remote. It is also
possible to clear the memory for
individual keys, or for the entire remote.
When a memory position is cleared, the
remote will return to the original factory
preset command.
To clear the memory for a specific
individual key location, put the
switch in the
Use/Learn
Learn
position. Press the
Main Power Off b
button and the button to be cleared at the
same time. Both the
and
Sending
indicators will light
Learning
momentarily. When the lights go out, the
memory has been cleared of the user
programmed code and returned to the
factory preset. Return the
Use/Learn
switch to the
position when you
a
Use
are finished.
To clear the remote's entire memory
and return all keys to their factory preset
commands first put the
Use/Learn a
switch in the
position. Then press
Learn
the
button
and
b
Main Power On
confirm that the
indicator
Learning
has illuminated. While continuing to
press the
button, press and
Power On
hold the
button until the
Power Off b
indicator goes off for about 3
Learn
seconds. It will then blink twice. Then
release the two buttons. This indicates
that the memory has been cleared of any
user programmed commands and that
the original commands have been
restored. Slide the
switch
Use/Learn
back to the
position to return
Use a
the remote to normal operation.
y

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents