Harman Kardon AVR80 Owner's Manual page 28

Audio/video receiver
Hide thumbs Also See for AVR80:
Table of Contents

Advertisement

AVR80 manual
11/01/98 13:01
A. To use the front panel buttons simply
press and hold
TUNE
until the desired letter or number
appears. Note that the upper case
alphabet will appear, followed by the
numbers
through
1
0
indicating a blank space. Tapping the
button will advance the display one
character at a time; holding it down will
move the display quickly. If you pass by
the desired character, use the
to move the display in reverse.
^
After entering the first character, press
to move to the next position
MEMO Ú
and note that the next digit will blink.
Use the same procedure outlined above to
enter a character.
When you have entered a digit or "blank"
in all five spaces, press
more than 1 second to confirm the entry
B. To use the remote for character entry,
press the button corresponding to the
desired letter or number. Press it once to
enter the first printed letter, twice for the
second, three times for the third and four
times for the number. Press the "
button to enter a blank space. (For
example, press the "
ABC
to enter an "
", three times for a "
A
and four times to enter a "
Use the
button
MEMO
the next digit position. When all five
spaces have been filled, press
again for more than 1 second to confirm
the entry.
Once a station name has been attached to
a preset position, the station's frequency
will appear briefly when the unit is tuned
to that station. After a few seconds the
preset name will appear in the display.
Side 22
Basic Operation
button
^
, and then a
Tuning Preset Stations
Stations preset into the tuner's memory
may be recalled in a number of ways.
1. To recall a station directly enter a
TUNE
¤
number from 1 to 30 using the number
buttons on the remote s
a. To enter a single digit memory
location, press
or enter the number and wait a few
seconds.
b. If an invalid number (other than
for
1–30) is entered in error, that
MEMO Ú
number will flash to alert you that
the entry is invalid and the display
will return to the previous frequency
display.
2. To scan through the list of preset
stations, press the
"
on the front panel
9
¤
CHANNEL
" button once
Press once to move up or down through
"
the memory presets one by one, or press
C
".)
and hold the button to quickly scan
1
through the list of stations.
to move to
o
3. To automatically review each station
in the memory, press the
MEMO
button
n %
indicator
The tuner will move up through the list
of stations, pausing to play each for five
seconds. Note that preset numbers where
no station has been programmed will be
skipped.
22
When the desired station is reached press
P-SCAN %
Clearing Preset Stations
Once stations are programmed into the
preset memories, it is possible to remove
them individually or as a group.
.
m
To remove a single station from the
memory:
before the number,
0
1. Recall the station by pressing the
buttons on the remote corresponding to
the station's memory location.
2. Press the
and observe that the
will blink.
3. While the indicator is blinking, press
the
button on the remote within five seconds.
or
The word
P-SET
P-SET
or the
confirm that the memory position has
$
buttons
remote
.
been cleared.
k
‡ ·
To clear
volume level and surround mode
memories:
1. Press the
the
P-SCAN
. Note that the
time for some seconds, until
P-SCAN
will blink.
MEMO
NOTE: When a complete memory clear is
performed the AVR80 will turn off as part
of the process. After clearing the memory
it is necessary to reset all stations and set
up parameters.
or
.
CLEAR Û
button
or
Ú
o
MEMO
£
indicator
MEMO
button
-not the
Û
CLEAR
CLEAR
will show briefly to
CLEAR
all memory locations, the
button
and
Ú o
MEMO
button
at the same
Û m
CLEAR
CLEAR
appears on the display.

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents