Messages; On The Unit's Display - Panasonic Diga DMR-EX98VEB Operating Instructions Manual

Messages

On the Unit's Display

H , F
(" " stands for a service number.)
DVD
(" " stands for a number.)
GUIDE
HARD ERR
NoCASSETTE
NoERAS
NoREAD
NoWRIT
FINAL
PLEASE WAIT
PROG FULL
PROTECT
REMOVE
SP 35:50, LP 151h
("SP", "LP" and the numbers are
examples.)
SW-DL
UNSUPPORT
UNFORMAT
F74
F75
U59
U61
U76
U80
U81
U99
U88
X HOLD
The message is alternately displayed.
92
RQT9089
• An error has occurred. The number following "H" or "F" depends on the
status of the unit. Check the items below and in the Troubleshooting Guide.
If the service number still does not disappear after the check, reset the unit
(➔ 94, "To restore the unit if it freezes" ).
• If the service numbers fail to clear, note the service numbers and contact a
qualified service person.
• The remote control and the main unit are using different codes. Change the
code on the remote control.
• GUIDE Plus+ data is being downloaded.
• If there is no change after turning the unit on and off, consult the dealer where
the unit was purchased.
• You have not inserted a video cassette for the recording.
• You cannot delete items on this disc.
The disc may be damaged. Use a new disc.
• The disc is dirty or badly scratched. The unit cannot record, play, or edit.
• The disc may be incompatible or of poor quality.
• You have used a lens cleaner and it has finished operation. Press
[ ; OPEN/CLOSE] on the main unit to eject the disc.
• You cannot write to this disc.
The disc may be damaged. Use a new disc.
• When the screen asking if you want to finalise the disc appears, the message
is displayed.
• Displayed when the unit is started. This is not a malfunction.
• The unit is carrying out its recovery process. You cannot operate the unit while
• There are already 32 timer recording programmes. Delete unnecessary timer
recording programmes.
• You have inserted a video cassette without the accidental erasure prevention
tab. Use a video cassette with an accidental erasure prevention tab.
• The USB device is drawing too much power. Remove the USB device.
• Available space on the HDD or disc.
The example "SP 35:50" is displayed when less than 100 hours are available
and the example "LP 151h" is displayed when over 100 hours are available.
"SP" and "LP" are recording modes, "35:50" means "35 hours 50 minutes" and
"151h" means "151 hours".
• The unit is performing a software update.
• You have inserted a disc the unit cannot play or record onto.
• You tried to operate with a non-compatible USB memory.
• You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL
or DVD-RW (DVD-Video format) that has been recorded on other equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted.
• The HDMI connection could not be authenticated due to a transfer malfunction.
Consult the dealer where the unit was purchased.
• The HDMI connection could not be authenticated due to an internal data malfunction.
Consult the dealer where the unit was purchased.
• The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until
the message disappears.
Select a position with good ventilation when installing the unit. Do not block
the cooling fan on the rear of the unit.
• (When a disc is not inserted) Displays when a malfunction has occurred
during recording, playback or copy to VHS etc. This is displayed when the unit
is in the recovery process to return to normal operation; it is not broken. Once
the display disappears you can use the unit again.
• HDMI cannot be output because you are connected to a model that does not
support copyright protection.
• The unit fails to operate properly. Press [ ^ /I] on the main unit to switch the unit
to standby mode. Press [ ^ /I] on the main unit again to turn the unit on.
• There was something unusual detected with the disc while recording, playing or copying;
there was a power failure or the AC mains lead was disconnected while the unit was on.
The unit is carrying out its recovery process. This process restores the unit to normal
operation. The unit is not broken. Wait until the message disappears.
• The Child Lock function is activated.
Press and hold [OK] and [RETURN] at the same time until "X HOLD" disappears.
Page
−
−
94
84
−
89
−
6
15, 16
7
−
29
−
−
35
89
−
−
84
15, 16
17
76
−
−
−
−
−
−
96
85