General - Payne PG8JAA042090AAJA Installation And Operating Instructions Manual

Tab{e 10-GAS RATE (CU FTfHR)
SECONDS SIZE OF TEST DIAL SECONDS SIZE OF TEST DIAL
FOR 1 1 2 5 FOR 1 1 2 5
REVOLUTION Cu Ft Cu Ft Cu Ft REVOLUTION Cu Ft Cu Ft Cu Ft
10 360 720 1800 50 72 144 360
11 327 655 1636 51 71 141 355
12 300 600 1500 52 69 138 346
13 277 555 1385 53 68 136 340
14 257 514 1286 54 67 133 333
15 240 480 1200 55 65 131 327
16 225 450 1125 56 64 129 321
17 212 424 1059 57 63 126 316
18 200 400 1000 58 62 124 310
19 189 379 947 59 61 122 305
20 180 360 900 60 60 120 300
21 171 343 857 62 58 116 290
22 164 327 818 64 56 112 281
23 157 313 783 66 54 109 273
24 150 300 750 68 53 106 265
25 144 288 720 70 51 103 257
26 138 277 692 72 50 100 250
27 133 267 667 74 48 97 243
28 129 257 643 76 47 95 237
29 124 248 621 78 46 92 231
30 120 240 600 80 45 90 225
31 116 232 581 82 44 88 220
32 113 225 563 84 43 86 214
33 109 218 545 86 42 84 209
34 106 212 529 88 41 82 205
35 103 206 514 90 40 80 200
36 100 200 500 92 39 78 196
37 97 195 486 94 38 76 192
38 95 189 474 96 38 75 188
39 92 185 462 98 37 74 184
40 90 180 450 100 36 72 180
41 88 176 439 102 35 71 178
42 86 172 429 104 35 69 173
43 84 167 419 106 34 68 170
44 82 164 409 108 33 67 167
45 80 160 400 110 33 65 164
46 78 157 391 112 32 64 161
47 76 153 383 116 31 62 155
48 75 150 375 120 30 60 150
49 73 147 367
---5 e Furnace should cycle off within 2 minutes. If gas does not
shut offwithin 2 minutes, detem_ine reason &aft safeguard
switch did not ffmction properly and correct condition.
f\ Remove blockage fl'om furnace vent elbow.
g. Switch will autooreset when it cools.
--> h. Reoinstall vent connector.
---5 NOTE: Should switch remain open longer than 3 minutes,
furnace control board will lockout the f:urnace for 3 hours. To reset
furnace control board, turn thermostat below room temperature or
from HEAT to OFF and mrn 115v power OFF, then back ON.
3. (hock Pressure Switch
This contlol proves operation of the &aft inducer blower.
a. Turn off l!5ov power to fhrnace.
b. Disconnect inducer motor lead wires from wire harness.
c. Turn on 115or power to furnace.
d. Set thermostat to "call for heat" and wait 1 minute. When
pressure switch is flmctioning properly, hot surface igniter
should NOT glow and control diagnostic light flashes a
--€
35
status code 32. If hot surfSce igniter glows when inducer
motor is disconnected, shut down furnace immediately
e DeteImine reason pressure switch did not function properly
and con'ect condition.
f\ Turn off 115or power to ft_rnace.
g. Reconnect inducer motor wires, replace outer door, and
turn on 115-v power.
h. Blower will run for 90 sec befbre beginning the call fbr
heat again.
i. Furnace should ignite nom_ally.
Step 5--ChecHist
1 Put away tools and instruments. Clean up debris.
2. (hock that blower OFFoDELAY time is selected as desired.
3. Verii) that blower and burner access doors are properly
installed.
4 (ycle test fhmac¢ with room thermostat.
5. (hock operation of accessories per manuitacturer's instruc=
tions
6 Review / se*'s Guide with owner
7 Attach literature packet to fi/mace.
SERVBCE AND MAINTENANCE PROCEDURES
FIRE, INJURY, OR DEATH HAZARD
Failure to fbllow this warning could result in possible damage
to this equipment, serious personal injury, or death
The ability- to properly perform maintenance on this equip°
ment requires certain knowledge, mechanical skills, tools, and
equipment. If you do not possess these, do not attempt to
perform any maintenance on this equipment other than those
procedures recommended in the User's Manual.
ELECTRICAL SHOCK, FIRE, OR EXPLOSION
HAZARD
Failure to follow this warning could result in personal injury,
death, or property damage
Before servicing_ disconnect all electrical power to ftlmace
Verif)- proper operation after servicing.
ELECTRICAL OPERATION HAZARD
Failure to fbllow this caution may result in improper furnace
operation or failure of tim_ace
Label all wires prior to disconnection when selwicing con-
tIols Wiring errors can cause improper and dangerous
operation.
Step l--htroduction
GENERAL
These instructions are written as if the furnace is installed in an
upflow application. An upflow furnace application is where the
blower is located below the combustion and controls section of the
furnace, and conditioned air is discharged upward. Since this
ff_rnace can be installed in any of the 4 positions shown in Fig 4,
you must revise your orientation to component location accord-
ingly.