Table of Contents
Advertisement
--€
TaNe l 1--FILTER
SIZE _NFORMATION (iN.)
FURNACE
CASBNG W_DTH
14-1/2
17-1/2
21
24**
* Recommended
**
Some furnaces may have 2 filters
FILTER QUANTITY
AND S_ZE
Side Return
Bottom Return
(1) 16X25X
I
(1) 14X25X
1
(1) 16X25X
I
(1) 16X25X
1
(1) 16X25X
1
(1) 20X25X
1
(I) 16X25X
I
(I) 24X25X
1
FILTER
TYPE
Cteanabte*
Cteanabte*
Cteanabte*
Cleanable*
Step
2--Care
and Maintenance
FIRE
OR EXPLOSION
HAZARD
Failure to %llow
this warning
could result in corrosion
of heat
exchanger,
fire, personal
inju_',
or death
Never
store anything
on, near, or in contact
with the I:t_rnace,
such as:
1. Spray
or aerosol
cans,
rags,
brooms,
dnst mops,
vacuum
cleaners,
or other cleaning
tools.
2. Soap powders,
bleaches,
waxes
or other
cleaning
corn=
pounds,
plastic
or plastic
containers,
gasoline,
kerosene,
cigarette
lighter
fluid, dry cleaning
fluids, or other volatile
fluids.
3. Paint
thinners
and other painting
compounds,
paper
bags,
or other paper
products.
For continuing
high per%rmance
and to minimize
possible
equip=
ment
fg_ilure, periodic
maintenance
must
be performed
on this
equipment.
Consult
your local
dealer
ahont
proper
fiequency
of
maintenance
and the availability
of a maintenance
contract
ELECTRICAL
SHOCK
HAZARD
Failure
to follow
this warning
could result
in personal
injury,
death or product
damage.
Turn
off the gas and electlical
supplies
to the unit before
performing
any maintenance
or service
Follow
the operating
instructions
on the label
attached
to the ftmaace.
(ARBON
MONOXIDE
POISONING
AND
FIRE
HAZARD
Failure to follow
this warning
could
result
in fire, personal
injury,
or death
Never
operate
unit without
a filter or with filter
access
door
removed.
1
CUT HAZARD
Failure
to fbllow
this caution
may result
in personal
ir_jury.
Sheet metal parts may have sharp edges or bun's. Use care and
wear
appropriate
protective
clothing,
safety
glasses,
and
gloves
when
handling
parts
and servicing
Nmaces.
The minimnn_
maintenance
on this fm_aace is as %llows:
1. (hock
and clean
air filter each month
or more
fiequently
if
required.
Replace
if torn.
2. Check blower
motor
and wheel
for cleanliness
each heating
and cooling
season.
Clean
as necessm 7.
3. (hock
electrical
connections
_br tighmess
and
controls
for
proper
operation
each heating
season.
Service
as necessm_-.
--€
37
4. Inspect
burner
compartment
be%re
each heating
season
%r
rnst,
corrosion,
soot
or excessive
dust.
If necessa_,
have
_ul_ace
and burner
serviced
by a qualified
service
agency.
5
Inspect
the vent pipe/vent
system
before
each heating
season
_br rust,
corrosion,
water
leakage,
sagging
pipes
or broken
fittings.
Have
vent pipes/vent
system
serviced
by a qualified
service
agency.
6. Inspect
any
accessories
attached
to the
t_t_mace such
as a
humidifier
or electronic
air cleaner.
Pert'ram
any service
or
maintenance
to the accessories
as recommended
in the acces-
so_- instractions.
CLEANING
AND/OR
REPLACING
AIR FILTER
The air filter arrangement
will vary depending
on the application.
The filter is exterior
to the J:i/mace casing.
NOTE:
If the filter has an airflow
direction
an'ow, the arrow must
point towards
the blower.
CUT
HAZARD
Failure
to %llow
this caution
may result
in personal
injury.
Sheet metal parts may have sharp edges or burrs
Use care and
wear
appropriate
protective
clothing,
safety
glasses,
and
gloves
when
handling
parts
and sela'icing
I:_/maces.
Media
cabinet
filter
procedures:
NOTE:
Media
cabinet
or 1" Filter
Rack
are accessories
and are
not included
t'rom the factory
with the standard
_ilrnace model
1
Turn
off electIical
supply
to furnace
before
removing
filter
access
door.
2
Remove
filter cabinet
door
3
Slide filter
out of cabinet.
4
If equipped
with permanent,
washable
1-inch filter, clean filter
by spraying
cold tap water
through
filter in opposite
direction
of airflow.
Rinse
filter
and let dry. Oiling
or coating
of the
filter is not recommended.
See Table
11 for size int'ornaation.
5. If equipped
with
_bctory=specified
disposable
media
filter,
replace
only
with media
filter
having
the same part number
and
size.
For
expandable
replacement
media,
refer
to the
instrnctions
included
with the replacement
media.
If equipped
with KGAFR0301ALL
external
filter rack, See Table
11.
6. Slide filter
into cabinet.
7. Replace
filter cabinet
door.
8. Turn on electrical
supply
to ft_rnace.
BLOWER
MOTOR
AND
WHEEL
ELECTRICAL
SHOCK
HAZARD
Failure
to follow
this warning
could result
in personal
injury
or death.
Blower
access door switch
opens
115=v power
to control.
No
component
operation
can
occur
unless
switch
is closed.
(aution
must be taken when manually
closing
this switch
for
service
purposes.
NOTE:
The
blower
wheel
should
not be
dropped
or bent
as
balance
will be affected.
Tile foHmving
steps should
be performed
by a quMified
service
agenc?°
To ensure
tong life and high eNciency,
clean accumulated
dirt and
grease
from blower
wheel
and motor annually.
Hide quick links:
Advertisement
Table of Contents
