System Menu - American DJ Accu Spot 250 Hybrid User Instructions

Accu Spot 250 Hybrid
5-Pin XLR DMX Connectors.
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting stan-
dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
American DJ - www.americandj.com - Accu Spot 250 Hybrid Instruction Manual Page 13
®
Some manufactures use 5-pin DMX-
5-Pin XLR Male (In)
Pin 1 Pin 1
Pin 2 Pin 2
Pin 3 Pin 3
Pin 4 - Do Not Use
Pin 5 - Do Not Use
Control board show menu of ACCU SPOT 250HYBRID
Set Up Accu Spot 250 Hybrid
0 ADDR AXXX A001
1 TEST T-01~T-XX
RUN
AUDI
2 PLAY
AUTO
3 LAMP ON/OFF
ALL
SCAN
COLR
4 RESE
GOBO
SHTR
LIFE
LAMP
5 TIME
CLMP
6 RPAN ON/OFF
7 RTLT ON/OFF
8 MIC M-XX
VALU
9 DISP D ON
FLIP
LAAU
RDMX
DLOF
DLAY
SPOT
10 SPEC
DFSE
FEED
VER
ADJU
STEP
SCXX
11 EDIT
REC.
RUN
American DJ
®
MSTR/ALON
MSTR/ALON
Clos/Hold//Auto/Audi
0000~9999
0000~9999
D–XX D-00 (DXXX)
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
D–XX D-05
ON/OFF
ON/OFF
ON/OFF
V1.0~V9.9
CODE CXXX
CH01~CH30 XXXX(-128~127)
S–01 ~S–48
0 1 XX(00~FFH)
C–01~C–30
3 0 XX(00~FFH)
TIME T XXX(001~999)
CEDT ON/OFF
RE.XX
ON/OFF
- www.americandj.com - Accu Spot 250 Hybrid Instruction Manual Page 14

System Menu

Indicate the staring DMX address
A001 also is the setting for slave
Automatically test the function
Runs fixture as "master" or "alone" for auto
Runs fixture as "master" or "alone" for
audio
No DMX Status
Manually switches lamp "on" and "off"
Reset all motors and returns fixture to home
Reset only motors for pan/tilt
Reset only motors for colors
Reset only motors for gobo and rotation
Reset only motors for shutter and/or dimmer
Displays the total fixture running time
Displays a lamps running time
Clear lamp running time
Reverses the pan movements
Reverses the tilt movements
Mic sensitivity
Display the DMX512 value of each channel
Display turn off after 2mins
This function will reverse the display 180
Automatic lamp start with power
Change DMX address via external controller
Switch lamp via DMX
Lamp on delay time
Lamp optimization
Resets all the fixture functions to default
Pan/tilt feedback (error correction) on/off
Software version
Fixture code *code is "C050"
Motor Calibration
Set the amount of your program
Edit the channels of each scene
Time for each scene
Edit program via controller
Auto Save
Program test