Additional Information; Learning More About This System - JVC UX-DM8 Instructions Manual

Learning More about This System

Getting Started
(see pages 3 to 5)
Connections:
• Make sure the antenna conductors do not touch any other
terminals, connecting cords or the power cord. Also, keep
the antennas away from metallic parts of the System,
connecting cords, and the AC power cord. This could cause
poor reception.
• Use only speakers with the same speaker impedance as
indicated by the speaker terminals on the rear of the System.
• If the power cord has been unplugged for more than 1 day,
the System turns on automatically when you connect the
cord again.
Daily Operations—Playback
Listening to the Radio:
• If you store a new station into an occupied preset number,
the station previously stored in that number will be erased.
Playing Back a Disc/Track:
• When you change the source to "CD" or "USB," it may
take a while to activate the source.
• This System can recognize up to 4 000 tracks in a disc/USB
device/built-in memory. Also, the System can recognize up
to 150 tracks (for a disc) or 999 tracks (for a USB device/
built-in memory) per group and up to 99 groups in a disc/
USB device/built-in memory.
– If there are any unplayable tracks in a group, those tracks
are also counted in the total track number.
• For playback of files in the USB device...
– When connecting a USB device, refer also to its manual.
– Connect one USB device to the System at a time. Do not
use a USB hub.
– You can charge the USB device through the
Memory) jack of this System.
– While playing back/recording/editing tracks or groups in
a USB device, do not disconnect the device. It may cause
malfunction on both the System and the device.
– JVC bears no responsibility for any loss of data in the
USB device while using this System.
– This System is compatible with USB 2.0 Full Speed.
– You can play back MP3/WMA/WAV files in a USB
device (maximum data transfer rate: 2 Mbps):
– You cannot play back a file larger than 2 GB.
– This System cannot recognize a USB device whose
rating is other than 5 V and does not exceed 500 mA.
– This System may not play back some USB devices.
– This System may not play back some files even though
their formats are listed above.
– It will take some time to start up a USB device larger than
1 GB.
37

Additional Information

(see pages 6 to 11)
(USB
• For MP3/WMA/WAV playback...
– MP3/WMA/WAV discs require a longer readout time
than regular CDs. (It depends on the complexity of the
group/file configuration.)
– Some MP3/WMA/WAV files cannot be played back and
will be skipped. This results from their recording
processes and conditions.
– This System can play only a disc of ISO 9660 Level 1 or
Level 2.
– This System can play back MP3/WMA/WAV files with
the extension code <.mp3>, <.wma>, or <.wav>
(regardless of the letter case—upper/lower).
– It is recommended to make each MP3/WMA file at a
sampling rate of 44.1 kHz and at a bit rate of 128 kbps.
– It is recommended to make each WAV file at a sampling
rate of 44.1kHz and quantization bit rate of 16 bit.
Playing Back an other equipment:
• When QP Link fails due to a weak sound signal from the
AUX jack, Auto Standby may turn the System off even if
you can hear the sound from the speakers.
In such cases, adjust the volume level of the component
louder so that the System can detect the sound signal
properly.
• Changing from AUX to another source while QP Link is
working deactivates QP Link temporarily.
In this case, the following reactivate QP Link:
– Pressing QP LINK on the remote control twice.
– Unplug the component from the AUX jack, then plug it
in again.
• If you press (Standby/on) to turn the System off or if
preset Timer turns the System off while QP Link is
working, the System deactivates QP Link temporarily.
In such cases, the followings reactivate QP Link:
– When the sound signal from the AUX jack stops or is too
weak for about 30 seconds after the System is turned off.
– When you turn on the power again.
• QP Link may start working when you just plug in the
component to the AUX jack or unplug it. This is not
malfunction.
• In the following cases QP Link does not work:
– While recording.
– While recording using Recording Timer.
– While the System is turned off and display brightness is
changed to "DIMMER OFF" (see page 13).