Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Planet VIP-158
Summary of Contents for Planet VIP-158
- Page 1 VoIP Analog Telephone Adapter VIP-158 User’s manual Version 1.00 - 1 -...
-
Page 2: Ce Mark Warning
Copyright Copyright (C) 2007 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLANET Technology, This User’s Manual contains proprietary information protected by copyright, and this User’s Manual and all accompanying hardware, software, and documentation are copyrighted. - Page 3 Revision User’s Manual for PLANET VoIP Analog Telephone Adapter: Model: ATA Rev: 1.00 (2007, October) Part No. EM-VIP_158 - 3 -...
-
Page 4: Table Of Contents
Administrator Setting ......................... 17 Making the setting effective ....................... 18 Appendix A Voice communication samples....................19 Peer to peer (P2P) mode ........................19 SIP Proxy mode..........................20 Appendix B Frequently Asked Questions List..................21 Appendix C VIP-158 Specifications ......................22 - 4 -... -
Page 5: Chapter 1
Internet or corporation network with very low cost. With the VIP-158, SOHO users are able to save the installation cost and extend their past investments of telephones, conference and speakerphones. The VIP-158 can be the bridge between traditional analog systems and IP network with an extremely affordable investment. -
Page 6: Package Content
RJ-11 cable x 1 Physical Details The following figure illustrates the each panel of SIP ATA. VIP-158: SIP Analog Telephone Adapter (1 x RJ-45, 1 x RJ-11) Front Panel of VIP-158 Left / Right Panel of VIP-158 Top Panel of VIP-158... -
Page 7: Physical Interface & Button
Physical Interface & Button RESET Reset to the factory default setting 5V DC 5V DC Power input outlet RJ-45 connector, for Internet access, connected directly to Switch/Hub through straight CAT-5 cable. Phone RJ-11 connector, connected directly to the analog phone. Machine default IP is http://192.168.0.1. -
Page 8: Chapter 2 Preparations & Installation
Chapter 2 Preparations & Installation Physical Installation Requirement This chapter illustrates basic installation of ATA analog Phone Adapter (“ATA” in the following term) • Network cables. Use standard 10/100Base-TX network (UTP) cables with RJ45 connectors. • TCP/IP protocol must be installed on all PCs. For Internet Access, an Internet Access account with an ISP, and either of a DSL or Cable modem Administration Interface PLANET ATA provides GUI (Web based, Graphical User Interface) and utility for machine management... - Page 9 Web configuration access To start ATA web configuration, you must have one of these web browsers installed on computer for management • Microsoft Internet Explorer 6.00 or higher with Java support Default IP address of ATA is 192.168.0.1. You may now open your web browser, and insert http://192.168.0.1 in the address bar of web browser to logon ATA web configuration page.
-
Page 10: Chapter 3 Network Service Configurations
After TCP/IP configurations on your PC, you may now open your web browser, and input http://192.168.0.1 to logon Phone Adapter web configuration page. Enter the IP address of the VIP-158 which by default is 192.168.0.1 Phone Adapter will prompt for logon username/password: root / null (no password) - Page 11 Parameter Description IP Address LAN IP Address of the ATA Default : 192.168.0.1 Subnet Mask LAN mask of the ATA Default : 255.255.255.0 Default Gateway Gateway of the ATA Default : 192.168.0.254 DNS server of the ATA Default : Null PPPoE Username PPPoE user name of the ISP provider Default : Null...
- Page 12 Please be noticed that the Utility Tool is only designed Note for the LAN environment settgin. If the “Connect Type” is “PPPoE”, the Utility Tool can NOT find the device. - 12 -...
-
Page 13: Chapter 4 Voip Telephone Adapter Configurations
Chapter 4 VoIP Telephone Adapter Configurations SIP Account Settings In SIP you need to input the account and the related informations in this page, please refer to your ISP provider. You can register three SIP account in the ATA. You can dial the VoIP phone to your friends via first enable SIP account and receive the phone from these three SIP accounts. -
Page 14: Call Control Settings
SIP Proxy Server IP address or Domain Name Default : Null Server Port Port number of SIP register Server Default : 5060 SIP Port Port number of VIP-158 Default : 5060 SIP Name This SIP account Default : Null Username... - Page 15 Parameter Description RTP Port Initial port number for sending RTP packets. Default : 4100 RTP TOS (0 - 255) Type of Service value for Quality of Service. Default : 160 Default Codec Set the default voice codec to be “G.711 u-law”, “G.711 a-law” or “G.729A”.
-
Page 16: Provision Settings
Provision Settings The provision feature is for user to easily use ATA by plug & play without the complicated setting procedures. (Auto provisioning system is an advanced feature of SIP ATA. For further information on using this function, please contact your ISP.) If the ISP supports the auto-provisioning system, please select the “TFTP Provision”... -
Page 17: Administrator Setting
Parameter Descriptio TFTP Provision Set the auto-provisioning functionality. Default : Disable TFTP Server IP Shows the IP address of the TFTP server. Default : 0.0.0.0 Firmware Shows the filename of the firmware. Default : Null Firmware Upgrade Button for processing the functionality of “Function Upgrade” Administrator Setting User can change the “Username”... -
Page 18: Making The Setting Effective
Making the setting effective Aftersetting the above all, user should select “SUMBIT” button to deliver the new setting. From previous step, if users do not want to deliver the new setting values to the device, user can select “RESET” button to return the original settings. After step 1, select “REBOOT”... -
Page 19: Appendix A Voice Communication Samples
There are several ways to make calls to desired destination in ATA. In this section, we’ll lead you step by step to establish your first voice communication via keypad and web browsers operations. Peer to peer (P2P) mode Assuming there are two VIP-158 in the network the IP address are 192.168.0.1 and 192.168.0.2 VIP-158-A... -
Page 20: Sip Proxy Mode
200 / 123 (for VIP-158-B) for the voice calls. STEP 2: Please log in VIP-158-A via web browser, find to the SIP item. In the setting page, please insert the account/password information obtained from your service provider (in this sample, we’re using PLANET IPX-2000 as the IP PBX server for SIP account, call authentications),... -
Page 21: Appendix B Frequently Asked Questions List
I forget my ATA login username and / or password 1.) Restore VIP-158 to its factory default settings by pressing the “Reset” button which is at the back panel of the device for 5 seconds or more. -
Page 22: Appendix C Vip-158 Specifications
Appendix C VIP-158 Specifications Product SIP Telephone Adapter Model VIP-158 Hardware 1 x 10/100Mbps RJ-45 port 1 x RJ-11 connection Protocols and Standard Standard SIP 2.0 (RFC3261), STUN (RFC 3489), UPnP, MD5 for SIP authentication (RFC 2069 / RFC 2617) Voice codec G.729a, G.711...