Page 2
Barco nv Events Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.89.70 Fax: +32 56.36.88.24 E-mail: events@barco.com Visit us at the web: www.barco.com Printed in Belgium...
Page 3
Changes Barco provides this manual “as is” without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.
Definition Qualified service technicians or Qualified technicians : Persons having appropriate technical training and experience nec- essary to be aware of hazards to which they are exposed in performing a task and of measures to minimize the danger to themselves or other persons. R5976386 BARCOSLM G8 20/10/2004...
Page 10
1. Safety Instructions Extra Safety manual Read also safety instructions in separate manual (R5976125). R5976386 BARCOSLM G8 20/10/2004...
Lens Packaging • Projector Case 2.1 Box Content Content • 1 projector BARCO SLM G8 (weight ± 56 kg or 123.5 lbs) • 1 remote control unit RCU + 1 battery. • 1 European and 1 American power cable. •...
2. Packaging and Dimensions 2.4 Projector Case Dimensions The dimensions are given in mm 25.4mm = 1 inch FRONT VIEW IR-receiver AIR OUT AIR IN 64,5 520,5 Image 2-2 Front view dimensions Image 2-3 Side view dimensions R5976386 BARCOSLM G8 20/10/2004...
Page 13
2. Packaging and Dimensions Image 2-4 Top view dimensions R5976386 BARCOSLM G8 20/10/2004...
Page 14
2. Packaging and Dimensions R5976386 BARCOSLM G8 20/10/2004...
Digital MicroMirror Devices™ in which case there is a loss of warranty Which screen type ? There are two major categories of screens used for projection equipment. Those used for front projected images and those for rear projection applications. R5976386 BARCOSLM G8 20/10/2004...
Positioning the projector Table mounted, front projection Table/Top side facing ceiling SIDE VIEW Projector Screen Optical axis projection lens Floor CD = SH/2 + B - A Screen TOP VIEW Floor BACK VIEW Image 3-1 Table mounted configuration R5976386 BARCOSLM G8 20/10/2004...
Page 17
Table mounted configuration up side down Ceiling mounted, front projection Ceiling/Top side facing floor Ceiling Optical axis projection lens Projector CD = SH/2 + B - A Screen SIDE VIEW Screen CEILING VIEW Ceiling BACK VIEW Image 3-3 Ceiling mounted projector R5976386 BARCOSLM G8 20/10/2004...
Make sure the projector is located so that the air inlets and outlets for the cooling system are not obstructed. Leave a safety area A of about 1 meter on the left and the right side of the projector. R5976386 BARCOSLM G8 20/10/2004...
Page 19
3. Installation Guidelines Image 3-5 Safety area around the projector R5976386 BARCOSLM G8 20/10/2004...
Forwards and backwards tilting is allowed. 3.5 Mounting the projection lamp ARNING Unplug the power cord from the wall outlet before starting with the mounting procedure. ARNING Mounting the projection lamp should be done by qualified service technician. R5976386 BARCOSLM G8 20/10/2004...
Pull and remove the side cover 3.5.2 Installation of the new Lamp Unit. What has to be done First remove the lock nut on each spacer screw and next slide the lamp unit into the projector frame. R5976386 BARCOSLM G8 20/10/2004...
Page 22
2. Line up the lamp unit guides with the guides on the projector frame (B) and push the unit into the frame until it fits. (image 3-10) 3. Secure the position of the lamp unit with the 3 spacer screws. (image 3-11) Image 3-9 Lamp unit, removing the lock nuts R5976386 BARCOSLM G8 20/10/2004...
1. Move the cover guides under the back cover and push the front of the cover against the projector frame lining up the cover lock screw with the speed nut (A) on the frame. (image 3-12, image 3-13) 2. Turn with a screwdriver the side panel lock screw (B) a quarter turn clockwise to lock. (image 3-14) R5976386 BARCOSLM G8 20/10/2004...
A suggestion dialog box will be displayed when the projector is restarted after 100 hours and 250 hours. Once ENTER is pressed when that box is open, this box will not be displayed again till the next alert point is reached. R5976386 BARCOSLM G8 20/10/2004...
Page 25
Select with ↑ or ↓ Select with ↑ or ↓ then <ENTER> then <ENTER> <EXIT> to return. <EXIT> to return. then <ENTER> <EXIT> to return. Menu 3-2 Menu 3-3 Menu 3-4 Image 3-15 Lamp adjustment access R5976386 BARCOSLM G8 20/10/2004...
Do not use fabric softener when washing the cleaning cloth or softener sheets when drying the cloth. Do not use liquid cleaners on the cloth as doing so will contaminate the cloth. AUTION Other lenses can also be cleaned safely with this Toraysee cloth. R5976386 BARCOSLM G8 20/10/2004...
5. Guide hook and cable around the carry handle and guide it around the carry handle of the upper projector. (image 3-24) 6. Hook it in the foreseen hole B in the base plate of the upper projector. (image 3-25) R5976386 BARCOSLM G8 20/10/2004...
Page 30
3. Installation Guidelines Image 3-21 Stacking two projectors Image 3-22 Closing the rigging sockets Image 3-23 Image 3-24 Mounting the security chain Mounting the security hook R5976386 BARCOSLM G8 20/10/2004...
Page 31
1. Push the ring (A) of the first projector downwards and hold it in that position. (image 3-26) 2. Turn the locked part (B) of the second projector a quarter counter clockwise and move it upwards. Image 3-26 Opening the rigging sockets R5976386 BARCOSLM G8 20/10/2004...
2. Slide the clamps holders (2 per profile) on its place in the U-profile according the measured distance and secure this position. (image 3-29) 3. Turn the overlockers in the holes of the clamp holder. The overlocker can turn around. Image 3-29 Mounting the clamp — detail R5976386 BARCOSLM G8 20/10/2004...
Page 33
2. Hook the clamp around the tube. The trigger automatically shuts the clamp. 3. Close the fixation handle and secure it by turning the hand screw. (image 3-31) Image 3-30 Opening the rigging clamp Image 3-31 Closing the rigging clamp R5976386 BARCOSLM G8 20/10/2004...
Press a digit button to select an input source. EXIT ENTER STBY PAUSE TEXT FREEZ HELP PHASE SHARPNESS TINT COLOR STANDBY EXIT BRIGHTNESS ENTER CONTRAST TEXT PAUSE SHARPN TINT BRIGHTN PHASE COLOR CONTRAST Image 4-1 Standby indication R5976386 BARCOSLM G8 20/10/2004...
Page 36
When ENTER is pressed to go on, the warning will be repeated every 30 min. The total lifetime of the lamp for a safe operation is 1000 hours max. Do not use it longer. Always replace with a same type of lamp. Call a BARCO authorized service technician for lamp replacement. AUTION Using a lamp for more than 1000 hours is dangerous as the lamp could explode.
Variable inputs Two digital inputs available. • SDI input (R9840110) • HD SDI Digital input (R9840450) Digital Video Decoder (R9841170) 4.5.2 Inputs via RCVDS05 Overview When using a RCVDS05, the input configuration must be as follows: R5976386 BARCOSLM G8 20/10/2004...
Hardwired COMM PORT 10/(100)BASE-T remote RS232/422 IN RS232/422 OUT CTRL 1 SDI DIGITAL INPUT HD SDI DIGITAL MODULE High Bandwidth 5 CABLE INPUT DVI INPUT High Bandwidth 5 CABLE INPUT DVI INPUT DVI OUTPUT Image 4-4 R5976386 BARCOSLM G8 20/10/2004...
1. Press ADJUST or ENTER key to start up the Adjustment mode. 2. Push the cursor key ↑ or ↓ to select Installation. (menu 4-4) 3. Press ENTER. 4. Press the cursor key ↑ or ↓ to select Input Slots. (menu 4-5) R5976386 BARCOSLM G8 20/10/2004...
1. Connect the output of your SDI source to the input BNC of the SDI input. (image 4-5) Note: The input is always 75 Ω terminated. 2. If loop through is needed, use the OUT to connect to the next device. R5976386 BARCOSLM G8 20/10/2004...
1. Connect the output of your HD SDI source to the input BNC of the HD SDI input. (image 4-6) Note: The input is always 75 Ω terminated. 2. If loop through is needed, use the OUT to connect to the next device. R5976386 BARCOSLM G8 20/10/2004...
Which signal can be connected to the Digital Video Decoder module? Connector name/ Y/Vid S-Video Input signal Component Video Composite Video Video S-Video S-Video How to connect? 1. Connect the output of your source to the corresponding inputs on the Digital Video Decoder module. (image 4-7) R5976386 BARCOSLM G8 20/10/2004...
Page 43
Select with ↑ or ↓ Select with ↑ or ↓ Select with ↑ or ↓ then <ENTER> then <ENTER> <EXIT> to return. then <ENTER> <EXIT> to return <EXIT> to return. Menu 4-7 Menu 4-9 Menu 4-8 R5976386 BARCOSLM G8 20/10/2004...
How to connect a COM800 Setup Always use the Barco COM 800 Splitter, R9827941 (240V) or R9827948 (110V), when using the COM 800 protocol. 1. Use a data cable with at least 9 cores and 2 DB9 female connectors, just cross the pin 2 and pin 3 connection to make a Custom Null Modem Cable.
Page 45
4. Connections Female Connector Pin Number 4 5 6 7 8 9 Pin Number 1 2 3 4 5 6 7 8 9 Female Connector Image 4-8 Make a Custom Null Modem Cable R5976386 BARCOSLM G8 20/10/2004...
Page 46
Red Stand-by CTRL 3 CTRL 2 Hardwired Sync OK remote CTRL 1 RS 232/422 IN RS 232/422 OUT COMM PORT 10(/100)BASE-T Read instructionsbefore connecting periphals To next COMM 800 Splitter Image 4-9 Com 800 Connection R5976386 BARCOSLM G8 20/10/2004...
Once the web site is accessed, it is possible to check and manipulate all the projector settings. Remote diagnostics, control and monitoring of the projector can then become a daily and very simple operation. The network connectivity permits to detect potential errors and consequently improve the time to servicing. R5976386 BARCOSLM G8 20/10/2004...
HD SDI DIGITAL MODULE High Bandwidth 5 CABLE INPUT DVI INPUT High Bandwidth 5 CABLE INPUT DVI INPUT DVI OUTPUT Ethernet connection Image 4-10 Always use an Ethernet cable with ferrite core to connect the projector to the LAN. R5976386 BARCOSLM G8 20/10/2004...
The following table gives an overview of the different functionalities of the keys. EXIT ENTER TEXT FREEZ STBY PAUSE HELP PHASE SHARPNESS TINT COLOR STANDBY EXIT BRIGHTNESS ENTER CONTRAST TEXT PAUSE SHARPN TINT BRIGHTN PHASE COLOR CONTRAST Image 5-1 Local keypad & RCU R5976386 BARCOSLM G8 20/10/2004...
Starting image projection. 1. Press Stand by key once on the local keypad or on the remote control. The projector mode indication lamp will be green (image 5-2) Press a digit button to select an input source. R5976386 BARCOSLM G8 20/10/2004...
Automatic shutdown is activated.’. A ’-t’ appears on the LED display to indicate the user that the projector is switched to standby due to DMD temperature problems. Operating temperature range of the DMD : +10°C and +35°C. R5976386 BARCOSLM G8 20/10/2004...
Quick Lens Adjustment Quick zoom/focus adjustment 1. Press the Selection key *, Barco key. The zoom/focus menu will be displayed. (image 5-3) 2. Push the cursor key ↑ or ↓ to zoom and ← or → to focus the image.
Image 5-3 Press the selection key * to switch to another pattern. Different patterns are available. Quick shift adjustment 1. Press the Selection key *, Barco key. The zoom/focus menu will be displayed (image 5-3). 2. Press ENTER. The shift menu will be displayed. (image 5-4) 3.
1. Plug one end of the remote cable in the connector on the bottom of the RCU. 2. Plug the other end in the connector in the front panel of the projector labelled RC. (image 5-6) R5976386 BARCOSLM G8 20/10/2004...
Page 55
CTRL 1 SDI DIGITAL INPUT HD SDI DIGITAL MODULE High Bandwidth 5 CABLE INPUT DVI INPUT High Bandwidth 5 CABLE INPUT DVI INPUT DVI OUTPUT Pins XLR plug 1 Ground 2 Signal 3 Ground Image 5-7 R5976386 BARCOSLM G8 20/10/2004...
Every projector requires an individual address between 0 and 255 which can be set in the Service mode. When the address is set, the projector can be controlled now: • RCU for addresses between 0 and 9. • computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255. R5976386 BARCOSLM G8 20/10/2004...
When the Pause key is pressed, the image projection is stopped, a black screen will be displayed and the projector remains with full power for immediate restart. The sound is not interrupted. The display on front of the projector will show a "P". R5976386 BARCOSLM G8 20/10/2004...
Page 58
Select a source number. The Stand-by Key When the Stand-by key is pressed, the image projection is stopped and the projector goes to stand-by. This situation is used when a projection stop is planned for a longer period. R5976386 BARCOSLM G8 20/10/2004...
Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks to enter your password (Password protection is only available when the password strap on the controller module is ON, call an authorized service center to change the position of the password strap). R5976386 BARCOSLM G8 20/10/2004...
The menus will be displayed line by line in the same order as they were displayed on the projection screen. Adjustments can be done while the projector is running without projecting the disturbing menus on the screen. Use the cursor keys to scroll through the menus and press ENTER to activate the displayed menu. R5976386 BARCOSLM G8 20/10/2004...
RENAME FILE SERVICE COPY DELETE OPTIONS COLOR TEMPERATURE GAMMA DECODING RANDOM ACCES PICTURE TUNING ADJUSTMENT MODE DYNAMIC COLOR DEPTH NOISE REDUCTION INPUT BALANCE SHIFT SIZE SIDE KEYSTONE GEOMETRY BLANKING ASPECT RATIO SCENERGIX SAVE CHANGES Image 7-1 R5976386 BARCOSLM G8 20/10/2004...
(see "File Options", page 66). Files with a ~ in front of the file name are temporary files. These files will be deleted when switching to another source. R5976386 BARCOSLM G8 20/10/2004...
[Fit] : only the best fitting files will be displayed (with a distinction of ± 2 lines and line duration of ± 300 ns, if nothing is found within this small area, the projector continues searching until it finds something). R5976386 BARCOSLM G8 20/10/2004...
Select with ↑ or ↓ Select with ↑ or ↓ , → OPTIONS then <ENTER> <ENTER> to accept ↑ , ↓ , ← , → <ENTER>, <EXIT> <EXIT> to return <EXIT> to return Menu 7-9 Menu 7-10 Menu 7-11 R5976386 BARCOSLM G8 20/10/2004...
Active Lines number of horizontal lines determining the height of the projected image. This value is normally given in the specification of the source. If not, adjust until full image height is displayed (no missing lines) R5976386 BARCOSLM G8 20/10/2004...
Page 66
The choice exists to project [both] fields on the screen or only the [even] or [odd] field. This can be useful for 3D projection. Use the ENTER key to toggle between [both], [even] and [odd]. R5976386 BARCOSLM G8 20/10/2004...
Page 67
Undesirable elements or defects in a video picture. These may occur naturally in the video process and must be eliminated in order to achieve a high-quality picture. Most common in analog are cross color and cross luminance. Most common in digital are macroblocks, which resemble pixelation of the video image. R5976386 BARCOSLM G8 20/10/2004...
No changes are made. RENAME FILE From file name : Video525.c01 To file name : demo.c10 Select with ← or → Reprogram with ↑ or ↓ or numeric keys <ENTER> to confirm <EXIT> to return Menu 7-16 R5976386 BARCOSLM G8 20/10/2004...
1. Push the cursor key ↑ or ↓ to highlight Delete. (menu 7-20) 2. Press ENTER. The delete selection menu will be displayed. (menu 7-21) 3. Push the cursor key ↑ or ↓ to select a file name. R5976386 BARCOSLM G8 20/10/2004...
[index] : the files in the list will be sorted on the file extension. File Load 1. Press ENTER to toggle between [automatic] and [manual]. [automatic] : correct file will be loaded automatically. [manual] : correct file has to be loaded manually. R5976386 BARCOSLM G8 20/10/2004...
COLOR TEMPERATURE GAMMA DECODING [EBU] DYNAMIC COLOR DEPTH NOISE REDUCTION INPUT BALANCE Select with ↑ or ↓ then <ENTER> <EXIT> to return. Menu 7-27 This CTI function applies to PAL and NTSC video or S-video inputs only. R5976386 BARCOSLM G8 20/10/2004...
(image 7-3) G A I N R ED 2. 5 Image 7-3 7.3.4 Gamma What can be adjusted ? With the gamma correction adjustment, it is possible to accurately set the gamma of the projector image. R5976386 BARCOSLM G8 20/10/2004...
GAMMA DECODING [EBU] DYNAMIC COLOR DEPTH NOISE REDUCTION INPUT BALANCE Select with ↑ or ↓ then <ENTER> <EXIT> to return. Menu 7-31 7.3.6 Dynamic Color Depth Purpose Increases color contrast for all video and data sources. R5976386 BARCOSLM G8 20/10/2004...
Input Balance for RGB input signals • Input Balance for YUV signals • Returning to the factory defaults There are 2 different adjustment procedures, one for RGB (included Video and S-Video) and one for YUV input signals. R5976386 BARCOSLM G8 20/10/2004...
5. Adjust with the cursor keys ↑ or ↓ or ← or → until the red respectively blue noise becomes visible in the white areas and return one step. INPUT BALANCE BLACK BALANCE WHITE BALANCE DEFAULT Select with ↑ or ↓ then <ENTER> <EXIT> to return. Adjust red with ↑ or ↓ blue with ← or → Menu 7-36 R5976386 BARCOSLM G8 20/10/2004...
The default settings will be loaded. INPUT BALANCE BLACK BALANCE WHITE BALANCE DEFAULT Select with ↑ or ↓ then <ENTER> <EXIT> to return. Adjust red with ↑ or ↓ blue with ← or → Menu 7-39 R5976386 BARCOSLM G8 20/10/2004...
Select with ↑ or ↓ then <ENTER> then <ENTER> <EXIT> to return. <EXIT> to return. Menu 7-40 Menu 7-41 7.4.3 Shift What can be done ? The image can be shifted in a horizontal or vertical direction. R5976386 BARCOSLM G8 20/10/2004...
Enter the desired value with the numeric keys on the RCU. Always 3 digits should be entered. To toggle + to - or vice versa, use the up or down arrow key. 7.4.4 Size What can be done ? The size can be adjusted in a vertical or horizontal way. R5976386 BARCOSLM G8 20/10/2004...
7.4.5 Side Keystone What can be done? The side keystone adjustment is used to align the image if the projector is mounted at a non standard projection angle. R5976386 BARCOSLM G8 20/10/2004...
(or noise). A ’0’ on the bar scale indicates no blanking. Which blanking adjustments are available ? • top blanking • bottom blanking • left blanking • right blanking R5976386 BARCOSLM G8 20/10/2004...
Enter the desired value with the numeric keys on the RCU. Always 3 digits should be entered. To toggle + to - or vice versa, use the up or down arrow key. 7.4.7 Aspect Ratio Purpose To force the projector in a typical aspect ratio. E.g. projecting a 4:3 image in a 16:9 aspect ratio. R5976386 BARCOSLM G8 20/10/2004...
7.5 ScenergiX Overview • Order information • Introduction • Preparations • Scenergix • ScenergiX overlap zone (horizontal scenergix) • ScenergiX overlap zone (vertical scenergix) • ScenergiX size adjustment • Adjusting the black level of the images R5976386 BARCOSLM G8 20/10/2004...
Why ScenergiX ? When working in a multichannel setup the BARCO SLM G8 and its Soft Edge possibilities enable an image blending that gives the appearance of a single view, thus achieving realistic immersion for the majority of wide screen applications.
Overlap : number of pixels that overlap Horizontal resolution of 1 projector : 1024 for Graphics versions, 1280 for Reality versions, 1400 for SLM R12+. Total horizontal screen resolution : [(horizontal resolution of 1 projector) x 2] minus overlap. R5976386 BARCOSLM G8 20/10/2004...
1. Go to File –> Edit menu of first projector. 2. Enter value for vertical act (= Lact) as follows : Lact = [(vert.. resolution of 1 projector)/(Total Vert. screen resolution)] x (Verti. resolution source) 3. Vertical start (= Lstart) remains the same. R5976386 BARCOSLM G8 20/10/2004...
Set first the width of the first projector and repeat for the second one. (image 7-13, image 7-14) SCENERGIX STATUS [ON] - size - BOTTOM LEFT RIGHT - black level - LEVEL Select with ↑ or ↓ then <ENTER> <EXIT> to return. Menu 7-52 R5976386 BARCOSLM G8 20/10/2004...
Page 87
7. Random Access Adjustment Mode Image 7-12 Width selections Image 7-13 Width set up for projector 1 R5976386 BARCOSLM G8 20/10/2004...
3. Adjust the black level of area A until the black level of area A, B and C are equal. (image 7-15) SCENERGIX STATUS [ON] - size - BOTTOM LEFT RIGHT - black level - LEVEL Select with ↑ or ↓ then <ENTER> <EXIT> to return. Menu 7-53 Image 1 Image 2 Image 7-15 Black level adjustment R5976386 BARCOSLM G8 20/10/2004...
The input section of the SLM projector allows a combinations of different input signals which may be projected in the 2 windows of the PiP screen. The PiP window can be placed in one of the four corners of the main window. Image 7-16 Possible position for PiP R5976386 BARCOSLM G8 20/10/2004...
Select with ↑ or ↓ then <ENTER> <EXIT> to return. Menu 7-56 7.6.4 Position of Picture in Picture window What can be done? The PiP window can be placed in on of the four corners of the main window. R5976386 BARCOSLM G8 20/10/2004...
A message will be displayed to wait a few second while the system is saving the data. (menu 7-60) RANDOM ACCESS Message ADJUSTMENT MODE Saving data FILE SERVICE please wait PICTURE TUNING GEOMETRY SCENERGIX SAVE CHANGES Select with ↑ or ↓ then <ENTER> <EXIT> to return. Menu 7-59 Menu 7-60 R5976386 BARCOSLM G8 20/10/2004...
<ENTER> <EXIT> to return. then <ENTER> <EXIT> to return. Menu 8-1 Menu 8-2 8.2 Input Slots What can be done ? The input configuration of the variable inputs is shown in the Input slots menu. R5976386 BARCOSLM G8 20/10/2004...
If no 800 peripheral indication is made on the menu, there are still two possibilities, no RCVDS or VS05 connected or RCVDS is switched off. When a 800 peripheral is connected to the projector, the input slots are not accessible with the cursor key to toggle their function. R5976386 BARCOSLM G8 20/10/2004...
NO SIGNAL CONTRAST ENHANCEMENT CONVERGENCE CONFIGURATION LENS QUICK ACCESS KEYS INTERNAL PATTERNS Select with ↑ or ↓ Select with ↑ or ↓ then <ENTER> then <ENTER> <EXIT> to return. <EXIT> to return. Menu 8-8 Menu 8-7 R5976386 BARCOSLM G8 20/10/2004...
EFFECT [NO TRANSITION] SOURCE SWITCHING NO SIGNAL CONTRAST ENHANCEMENT CONVERGENCE CONFIGURATION LENS QUICK ACCESS KEYS INTERNAL PATTERNS Select with ↑ or ↓ <ENTER> to toggle then <ENTER> <EXIT> to return. <EXIT> to return. Menu 8-11 Menu 8-10 R5976386 BARCOSLM G8 20/10/2004...
5 min CONTRAST ENHANCEMENT CONVERGENCE CONFIGURATION LENS QUICK ACCESS KEYS INTERNAL PATTERNS Select with ↑ or ↓ Select with ↑ or ↓ then <ENTER> then <ENTER> <EXIT> to return. <EXIT> to return. Menu 8-13 Menu 8-12 R5976386 BARCOSLM G8 20/10/2004...
<ENTER> then <ENTER> <EXIT> to return. <EXIT> to return. Menu 8-17 Menu 8-16 8.6 Contrast Enhancement Purpose Increases contrast for all video and data sources. Contrast enhancement will reduce the light output of the projector. R5976386 BARCOSLM G8 20/10/2004...
Menu 8-21 8.8 Configuration What can be done? The way of physical installation of the projector can be defined to the projector. The following installation configurations are possible: • front/table • front/ceiling • rear/table • rear/table R5976386 BARCOSLM G8 20/10/2004...
NO SIGNAL CONTRAST ENHANCEMENT CONVERGENCE CONFIGURATION LENS QUICK ACCESS KEYS INTERNAL PATTERNS Select with ↑ or ↓ Select with ↑ or ↓ then <ENTER> then <ENTER> <EXIT> to return. <EXIT> to return. Menu 8-25 Menu 8-24 R5976386 BARCOSLM G8 20/10/2004...
4. When finished, press EXIT to go to the lens adjustment menu or press ENTER to go to the zoom/focus function. LENS ADJUSTMENT ZOOM/FOCUS SHIFT OPTIONS Select with ↑ or ↓ then <ENTER> <EXIT> to return. Menu 8-27 Press the selection key * to switch to another pattern. Different patterns are available. R5976386 BARCOSLM G8 20/10/2004...
LENS CLEAR ALL QUICK ACCESS KEYS INTERNAL PATTERNS Select with ↑ or ↓ Select with ↑ or ↓ then <ENTER> then <ENTER> <EXIT> to return. <EXIT> to return. Menu 8-31 Menu 8-30 No functions are preprogrammed. R5976386 BARCOSLM G8 20/10/2004...
<EXIT> to return. <EXIT> to return. Menu 8-35 Menu 8-34 8.12 Internal Patterns What can be done with these internal patterns? The projector is equipped with different internal patterns which can be used for measurement purposes. R5976386 BARCOSLM G8 20/10/2004...
PURITY CONFIGURATION PAGE CHAR LENS ALPHA_NUMERIC CHARS QUICK ACCESS KEYS INTERNAL PATTERNS Select with ↑ or ↓ Select with ↑ or ↓ then <ENTER> then <ENTER> <EXIT> to return. <EXIT> to return. Menu 8-37 Menu 8-36 R5976386 BARCOSLM G8 20/10/2004...
9.3 Identification What can be seen on the identification screen? The identification screen shows the general information of the projector. The following items will be displayed: • Type of projector: BARCO SLM G8 • Software version • Network module: yes •...
This item is password protected when the password strap is installed. The password function is enabled when the password strap, second switch of S2 on the controller module is installed. Consult an authorized Barco service technician to change the strap position. About password types.
<EXIT> to return. <EXIT> to return Menu 9-6 Menu 9-7 9.4.2 Access Control List What is possible? In the access control list the owner can set up the access possibilities for the user and the guest. R5976386 BARCOSLM G8 20/10/2004...
An access level can be added to the following items: • Adjustment mode • Barco logo • Change projector address • File delete • File delete all • Input balance • Installation • Random access • Serial communication • Service R5976386 BARCOSLM G8 20/10/2004...
1. Push the cursor key ↑ or ↓ to highlight Change Proj Address. (menu 9-15) 2. Press ENTER. The Change Projector Address menu will be displayed and the actual address will be filled in. (menu 9-16) 3. Push the cursor key ↑ or ↓ to highlight Common address. R5976386 BARCOSLM G8 20/10/2004...
CHANGE PROJ. ADDRESS RS422 TERMINATION [ON] SERIAL COMMUNICATION NETWORK LAMP DIMMING MORE... Select with ↑ or ↓ Select with ↑ or ↓ then <ENTER> then <ENTER> <EXIT> to return. <EXIT> to return. Menu 9-17 Menu 9-18 R5976386 BARCOSLM G8 20/10/2004...
2. Press ENTER to toggle between RS232 and RS422. Default : RS232 SERIAL COMMUNICATION PROJECTOR ADDRESS 001 BAUDRATE [115200] INTERFACE STANDARD [RS232] RS422 TERMINATION [ON] Select with ↑ or ↓ then <ENTER> <EXIT> to return. Menu 9-20 R5976386 BARCOSLM G8 20/10/2004...
Select with ↑ or ↓ <ENTER> to edit Select with ↑ or ↓ Reprogram with ↑ or ↓ then <ENTER> or numeric keys <EXIT> to return. APPLY to confirm <EXIT> to return Menu 9-22 Menu 9-23 R5976386 BARCOSLM G8 20/10/2004...
(number of lumens) (full line) is reached. As long as this power is below the maximum power of the lamp, the projector will gives a constant light output. Once the maximum power is reached, the projector will follow again the normal lamp life cycle curve. R5976386 BARCOSLM G8 20/10/2004...
Page 114
All projectors must have a different projector address between 1 and 12. All must have the same baud rate and RS mode. The constant light output setting of one projector must be in the master position. All others must be in the slave position. R5976386 BARCOSLM G8 20/10/2004...
Page 115
Using the lamp longer than the maximum run time may damage the projector. number of strikes Total times the lamp is started up. Z-AXIS indication to adjust the Z-AXIS of the lamp (see Re-adjustment of the lamp position in chapter Installation Guidelines). R5976386 BARCOSLM G8 20/10/2004...
(+ less noise) 9.10 Dimming What is possible The lamp can be dimmed in small steps only when the lamp is used in Normal mode. The dimming can be done between normal mode and economic mode. R5976386 BARCOSLM G8 20/10/2004...
OFF: no key on the RCU is used to display the BARCO logo. TEXT: the TEXT key on the RCU is used to display or to remove the BARCO logo with one single push on this key (only in operational mode).
<ENTER> <ENTER> to confirm <EXIT> to return. <EXIT> to return. <EXIT> to return. Menu 9-31 Menu 9-32 Menu 9-33 9.13 Preset Input Balance AUTION Changing these settings may seriously affect the performance of the projector. R5976386 BARCOSLM G8 20/10/2004...
BARCO LOGO MINIMUM DELAY [ON] ADD INS PRESET INPUT BALANCE ADVANCED PROCESSING DIAGNOSIS FACTORY DEFAULTS MORE... Select with ↑ or ↓ then <ENTER> <ENTER> to toggle <EXIT> to return. <EXIT> to return Menu 9-36 Menu 9-37 R5976386 BARCOSLM G8 20/10/2004...
INPUT SELECTOR 72H ### INPUT SELECTOR 98H ### INPUT SELECTOR 9AH ### LAMP MODULE A0H ### Select with ↑ or ↓ Select with ↑ or ↓ then <ENTER> <EXIT> to return. <EXIT> to return. Menu 9-40 Menu 9-41 R5976386 BARCOSLM G8 20/10/2004...
LPS1 Rectifier T. 037(105)C LPS2 Heats. PFC T. 029(100)C LPS3 Heats. LPS T. 028(100)C VOLTAGES Trafo T. 032(105)C FANSPEED Select with ↑ or ↓ then <ENTER> <EXIT> to return. <EXIT> to return. Menu 9-46 Menu 9-47 R5976386 BARCOSLM G8 20/10/2004...
<ENTER> <EXIT> to return. <EXIT> to return. Menu 9-50 Menu 9-51 Menu 9-52 Restoring the factory defaults can take a while. When finished, the projector will automatically reboot and those factory settings will be loaded. R5976386 BARCOSLM G8 20/10/2004...
A confirmation menu will be displayed : " <F1> will be used to quickly access this menu". (menu 10-1) CONFIRM QUICK ACCESS <F1> will be used to quickly access this menu. <ENTER> to confirm <EXIT> to cancel Menu 10-1 R5976386 BARCOSLM G8 20/10/2004...
Page 124
10. Programmable Function Keys R5976386 BARCOSLM G8 20/10/2004...
5. Fpix MHz: pixel frequency 6. Ftot : total pixels on one horizontal line. 7. Pact: active pixels on one horizontal line. 8. Ltot: total lines in one field 9. Lact: active lines in one field. R5976386 BARCOSLM G8 20/10/2004...
The Barco Control Manager has been successfully tested on Microsoft Windows platform (98/NT 4.0/Windows 2000) with Internet Explorer 4.0. On other platforms and with other browsers, it should run fine when the browser supports Java Applets and supports the Java Swing library.
Information on the Start Up page. The nick name of the projector is shown in the middle of the screen. E.g. default indicated as ’Barco - projector’. Below the loca- tion of the projector, default indicated as ’Location’. This name and location can be replaced by any other name or location, see Configuration window / Settings.
To select an item, click on it in the menu bar and select the desired item in the drop down menu. B.4 Control Overview • Start up • General Control • Source • Image Settings • Image Enhancement • Lens adjustment • Geometry adjustment • Blanking adjustment R5976386 BARCOSLM G8 20/10/2004...
How to select 1. Click on one of the buttons on the content pane. (image B-6) The indicated function can be switched on or off. When the green light in the button lights up, the function is on. R5976386 BARCOSLM G8 20/10/2004...
(image B-8) A value indication for the setting will be given just below the slide bar of the adjustment. Changing a setting will have immediate influence on the displayed image. R5976386 BARCOSLM G8 20/10/2004...
The possibility is offered to decode the NTSC video signals via the default American IRE standard or via the European EBU standard. Decoding a NTSC signal using the European EBU standard may result in a greenish tint. R5976386 BARCOSLM G8 20/10/2004...
B.4.7 Geometry adjustment What can be adjusted Shift, Size and Keystone can be adjusted. Image B-11 Geometry adjustment R5976386 BARCOSLM G8 20/10/2004...
Blanking adjustments affect only the edges of the projected image and are used to frame the projected image on to the screen and to hide or black out unwanted information (or noise). The blanking values are given in a text box below the image. A ’0’ value in the text box indicates no blanking. R5976386 BARCOSLM G8 20/10/2004...
Mail Set up • Security • Data & Time • Settings B.5.1 Start up Start up To start up the configuration window : 1. Click on configuration. A drop down menu will be displayed. (image B-13) R5976386 BARCOSLM G8 20/10/2004...
Weekly : fill out the exact hour in the ’at’ area and select a day (or days) out of the list. Monthly : fill out the exact hour in the ’at’ area and select the day of the month in the ’every monthly’ area. R5976386 BARCOSLM G8 20/10/2004...
Set up of the advanced user password. Handle as follow : 1. Enter the new password. Only x’s will be displayed on the screen while typing in the new password. 2. Click on apply to activate the password. R5976386 BARCOSLM G8 20/10/2004...
3. When summer time is active in your region and the time setting set up via the network time, check ’Daylight saving time’ to obtain the correct time setting during the summer. 4. Click on Apply to activate. The current time on projector will be adapted. R5976386 BARCOSLM G8 20/10/2004...
Projector name set up 1. Click in the projector name text field. 2. Fill out the projector nick name. Use the format : name@domain 3. Click on apply to add the projector name to the general start up screen. R5976386 BARCOSLM G8 20/10/2004...
To start up the control window: 1. Click on Diagnostics. A drop down menu will be displayed. (image B-18) Image B-18 Diagnostics start up page Available items • General Status • Job Log • Advanced Diagnostics R5976386 BARCOSLM G8 20/10/2004...
The job log screen gives an overview of the last 30 logs stored in the projector. Image B-19 Job log screen B.6.4 Advanced Diagnostics Overview The advanced diagnostics screen gives an overview of errors and warnings on motors, devices, I²C busses, drivers, etc. R5976386 BARCOSLM G8 20/10/2004...
Page 145
When a warning or error occured, one of the lights in the buttons will be red and the error list for that button will be expand on the right side of the advanced diagnostic screen. The occured error should be indicated by a red light. R5976386 BARCOSLM G8 20/10/2004...
Page 146
B. Barco Control Manager R5976386 BARCOSLM G8 20/10/2004...
Battery Installation image control Condition Check start up Configuration start page Environment Control Manager 125, 127 General Control Lamp mounting Lamp positioning Laser Beams Lenses Diagnosis 117–118 Mounting lamp Projector tilting SMPS Rigging accessories Voltages Rigging points R5976386 BARCOSLM G8 20/10/2004...
Page 148
Input Balance Dimming Black Balance Factory defaults Start up Identification 86–87 Lamp Quick selection Language Source Changing Window position Network Configuration Password 102–103 Activation Access Control List Projector 7, 52 Preset Input Balance Address Projector Address R5976386 BARCOSLM G8 20/10/2004...
Page 149
33, 47 Serial Communication 106–108 Switching on Baud rate Switching to standby 33, 47 Interface standard RS422 termination Start up Start up Temperature Side panel Ambient Installation source files standard Stacking Projectors Z-axis adjustment Standard source files R5976386 BARCOSLM G8 20/10/2004...