Page 2
WARNING Some dust created by power sanding, sawing, grind- ing, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. •...
Page 5
14. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury. G1028Z/G1029 Dust Collector 15. DO NOT OVER-REACH. Keep proper 16. REDUCE THE RISK OF UNINTENTION- 17. MANY WOODWORKING TOOLS CAN...
Additional Safety Instructions For 1. THIS DUST COLLECTOR IS TO BE USED FOR WOOD DUST COLLECTION ONLY. Do not use this dust collector to pick up liq- uids and metal scrap including, but not lim- ited to, nails and filings. Metallic debris will contact the spinning impeller and could spark.
30 amp slow blow for 110V or 220V operation. Fuses rated higher will not adequately protect the circuit. G1028Z/G1029 Dust Collector G1029 Wiring The G1029 Dust Collector is pre-wired for 220V. A plug is not provided with the G1029. Refer to Figure 1 for recommended 220V receptacle.
If you are unsure about the correct installation or modification of electrical circuits, please consult the advice of a qualified electrician. Failure to do so could result in serious personal injury. G1028Z/G1029 Dust Collector...
SECTION 3: INTRODUCTION Commentary Grizzly Industrial, Inc. is proud to offer the Model G1028Z/G1029 Dust Collector. These dust col- lectors are a part of Grizzly’s growing family of fine machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satis-...
Unpacking The Model G1028Z/G1029 Dust Collector is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, please call Customer Service immediately for advice. Save the containers and all packing materials for possible inspection by the carrier or its agent.
Your Model G1028Z/G1029 represents a moder- ate weight load in an average footprint. Most com- mercial or home shop floors should be sufficient to carry the weight of the Model G1028Z/G1029. If you question the strength of your floor, you can opt to reinforce it.
Mount the casters to the base plate using sixteen (16) ⁄ adjust- loose clothing after they Base "-18 x ⁄ " hex bolts provided. See Figure 2. Figure 2. Mounting casters to base. G1028Z/G1029 Dust Collector...
(4) ⁄ provided. Figure 3. Mounting collector to base. G1028Z/G1029 Dust Collector The outlet can now be attached to the main col- lector body. Insert the rubber gasket between the collector and lower outlet flange and secure using eight (8) See Figure 4.
Secure with two (2) 18 x Collector ⁄ "-18 x ⁄ " hex bolts provided. ⁄ " bolts provided, as shown in Figure 6. Figure 6. Mounting collector to brackets. G1028Z/G1029 Dust Collector ⁄ "-...
Tighten each hose clamp until snug as shown in Figure 7. Figure 7. Attaching flex hose. G1028Z/G1029 Dust Collector Bags Hook the top loop of the filter bag over the support bracket as shown in Figure 8.
-14- Inlet Press the “Y” inlet onto the inlet cover flange as shown in Figure 11. The inlet is secured to the collector body by a press-on fit. Figure 11. Installing “Y” inlet. G1028Z/G1029 Dust Collector...
On the other hand, the stationary system is more versa- tile and convenient. The Model G1028Z/G1029 is designed to be a central dust collector system. Locate the dust col- lector in an out of the way location such as a cor- ner or separate room.
However, the cost of specifically designed flexible duct can vary greatly. Grizzly offers polyethylene hose which is well suited for the removal of particulate matter, especially saw- dust, since it is durable and completely flexible.
Page 19
Copper Ground Wire Figure 12. Ground jumper wire when using plastic blast gates and metal duct. G1028Z/G1029 Dust Collector We also recommend wrapping the outside of all plastic ducts with bare copper wire to ground the outside of the system against static electrical build up.
The location of the main line duct and each branch line. The location of any obtrusion such as a joist or heating duct, that will require special duct routing. Branch Line Main Line Figure 14. Bird’s eye planning view. G1028Z/G1029 Dust Collector Dust Collector...
Operating your Model G1028Z/G1029 is simple and straightforward. Blast gates located at each of the machines controls the air flow from the woodworking machine to the dust collector. If a...
Washington location using the address in the Introduction. The specifications, drawings, and photographs illustrated in this manual represent the Model G1028Z/G1029 as supplied when the manual was prepared. However, due to Grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly.
GREEN GROUND WIRE, ARE INTERCHANGEABLE, THEREFORE COLORS ARE NOT SPECIFIED. -22- WIRE DIAGRAM 110 VOLT MOTOR WIRES BLACK YELLOW WHITE 220VOLT MOTOR WIRES YELLOW BLACK GREEN (GROUND) TO 110 VOLT POWER SUPPLY WHITE GREEN (GROUND) TO 220 VOLT POWER SUPPLY G1028Z/G1029 Dust Collector...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Do you think your purchase represents good value? ___Yes Would you recommend Grizzly Industrial to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times. ___Yes Comments:_________________________________________________...
Page 30
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here...