Page 2
To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to fil- ter out microscopic particles. G1032 Dust Collector...
TEST RUN...11 SET UP ...11 MOBILE ...12 STATIONARY ...12 SYSTEM GROUNDING ...13 MAINTENANCE ...14 GENERAL ...14 LUBRICATION ...14 CLOSURE...15 PARTS BREAKDOWN AND PARTS LISTS ...16 MACHINE DATA ...17 WARRANTY AND RETURNS...18 WARRANTY CARD...19 G1032 Dust Collector Table Of Contents PAGE...
11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. 16 A.W.G. 50ft 16 A.W.G. 100ft 14 A.W.G. 200ft 12 A.W.G. 300ft G1032 Dust Collector...
Additional Safety Instructions For Dust Collectors 1. This dust collector is to be used for wood dust collection only. DO NOT use this dust collec- tor to pick up liquids and metal scrap including nails and filings.
Otherwise, consider a dedicated circuit for your machine. A 110V plug is provided with the G1032. In the case of 220V operation, please call the service department for further information. Grounding...
The time you invest before you begin to use your Model G1032 will be time well spent. DO NOT operate this machine until you are com- pletely familiar with the contents of this manual.
Unpacking The Model G1032 Dust Collector is shipped from the manufacturer in a carefully packed carton. If you discover the machine is damaged after you’ve signed for delivery, please call Customer Service immediately for advice. Save the containers and all packing materials for possible inspection by the carrier or its agent.
Site Considerations When placing the G1032 Dust Collector in your shop, three major considerations should be addressed: working clearances, lighting and elec- trical, and circuit loading. Working Clearances: Be sure to allow your- self sufficient room to safely operate your machines in any foreseeable operation.
SECTION 4: ASSEMBLY Beginning Assembly Assembly of the G1032 is straightforward. We have organized the assembly process into steps. Please follow them in sequence. Caution: All die-cut metal parts have a sharp edge (called “flashing”) on them after they are formed.
" - 18 x ⁄ " hex bolts provided. Figure 3. Figure 3. G1032 Dust Collector Fan / Motor The collector body includes the fan assembly, switch, and motor which are preassembled at the factory. Set the collector body on top of the upper column plate so the intake portion faces the long portion of the base.
Slip the collection bag over the bottom edge of the collector and pull the strap tight to secure. slip the filter bag over the top edge of the collector and pull the strap tight to secure. Figure 6. Figure 6. G1032 Dust Collector...
G1032 Dust Collector Set Up The G1032 dust collectors can be either operat- ed as mobile or stationary units. There are advan- tages and disadvantages to both systems. The primary advantage of a mobile system is low expense of ducts and fittings.
-12- Stationary The G1032 can be set up as a stationary unit with the addition of a fixed duct system to service more than one machine at a time. The primary advantage of a stationary system is it eliminates...
If you connect the dust collector to more than one machine by way of a non-conducting branching duct system and blast gates, the system must still be grounded as mentioned above.
SECTION 7: MAINTENANCE General Periodic maintenance will ensure safe operation, long dust collector life, and low overall cost of operation. Routinely check the condition of the following items and repair or replace as necessary: Loose mounting bolts, collector body, outlet, and support bracket mounting bolts.
WARNING! As with all power tools, there is danger associat- ed with the Model G1032 Dust Collector. Use the tool with respect and caution to lessen the possi- bility of mechanical damage or operator injury. If...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Do you think your purchase represents good value? ___Yes Would you recommend Grizzly Industrial to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times. ___Yes Comments:_________________________________________________...
Page 22
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...