We are proud to offer the model g1028z/g1029z dust Collector. this machine is part of a growing grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of grizzly’s com-...
Collector avOiDiNG fiRES. do not allow steel to strike against impeller—this may produce a spark. sparks can smolder in wood dust for a long time before fire or flame is detected.
Compliance MUST be verified by a qualified electrician! NOTICE The Model G1028Z is prewired for 110v. if you plan to operate the machine at 220v, the motor must be rewired (see page 31). full Load amperage Draw this machine draws the following amps under maximum load: amp draw at 110v (prewired) ...
Circuit size ... 15 amps g1028z/g1029z dust Collector power Connection Device the type of plug required to connect your machine to power depends on the type of service you cur- rently have or plan to install.
Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condi- tion of your shipment, inventory the contents. g1028z/g1029z dust Collector...
(4) ⁄ "-18 x ⁄ "-18 x ⁄ " figure 7. mounting support bracket to base. ⁄ " flange bolts, as shown in lower outlet Flange ⁄ " flange bolts, as shown in figure lower support Brackets g1028z/g1029z dust Collector...
Page 17
9. hose Clamp figure 9. attaching flex hose onto collector body outlet. g1028z/g1029z dust Collector hook the top loop of the upper filter bag " flange bolts. (fabric) over the support bracket, as shown in figure 10.
— strange or unusual noises should be inves- tigated and corrected before operating the machine further. always disconnect the machine from power when investigating or correcting potential problems. turn the machine OFF. g1028z/g1029z dust Collector...
Workshop Planner will allow you to quickly and easily draw and print a basic shop layout. don't worry, non-grizzly brand machines can be substituted with grizzly machines for layout pur- poses. Note: After you're finished, make sure to save your layout for later modification.
Page 22
20. dust port size and quantity per Write the required CFm for each machine on your sketch, as shown in figure 21. 1203 1570 1990 figure 21. CFm requirements labeled for each 2456 average Dust port Size average machine. machine. g1028z/g1029z dust Collector...
Write your determined branch line sizes on your drawing, as shown in figure 23. g1028z/g1029z dust Collector figure 23. Branch line sizes labeled on sketch. here are some frequently asked questions when determining branch line sizes:...
4) moving machine closer to dust collector to eliminate duct length, and 5) reducing 90˚ elbows or replacing them with 45˚ elbows. g1028z/g1029z dust Collector System Grounding since plastic hose is abundant, relatively inex- pensive, easily assembled and air tight, it is a very popular material for conveying dust from woodworking machines to the dust collector.
Page 26
29. ensure that each machine is continu- ously grounded to the grounding terminal in your electric service panel. ground screw g1028z/g1029z dust Collector...
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly industrial will not be held liable for accidents caused by lack of training. g1028z/g1029z dust Collector...
G6163—4" Clamp G7343—5" Clamp G7361—6" Clamp h5228—7" Clamp h5238—8" Clamp h5253—9" Clamp these clamps feature lever latches and foam seals, and secure around the rolled ends of fit- tings and pipe. figure 33. dust collection pipe clamps. g1028z/g1029z dust Collector...
Page 29
4" through 9". figure 37. metal reducers & adapters. Metal Elbows these industrial metal elbows are available from 4"–8" with 90˚, 60˚, 45˚, or 30˚ curves. Call (800) 523-4777 or visit www.grizzly.com for more information and pricing. 90° 30° 45°...
3. machine is incorrectly mounted or sits unevenly. 4. motor fan is rubbing on fan cover. 5. motor bearings are at fault. g1028z/g1029z dust Collector Troubleshooting possible solution 1. Correct short/replace fuse in control box. 2. ensure circuit size is suitable for this machine;...
10. install a larger dust collector to power your dust collection system. 1. re-secure ducts and dust collection bag, making sure duct and bag clamps are tight and completely over the ducts and bags. 2. retighten bag clamps. g1028z/g1029z dust Collector...
The motor wiring shown here is current at the time of printing, but it match Always use the wiring diagram inside the motor junction box. switch. View this page in color at www.grizzly.com. g1028z/g1029z dust Collector 6-15 Plug your machine.
P1028020 HOSE CLAMP P1028021 HOSE LOWER BAG V2.1.08 P1028023 COLLECTOR SUPPORT P1028024 COLLECTOR P1028025 PACKING (G1028Z) P1028026 UPPER BAG SUPPORT UPPER BAG V2. 1.08 P1028028 GASKET INLET CAP 6" 6"x4"x4" Y-INLET V2.10.01 PK32M KEY 6 X 6 X 28 PWRCRD220S POWER CORD PWRCRD220L MOTOR CORD CLAMP V2.