Congratulations - Heat & Glo NORTHSTAR-BK Owner's Manual

Congratulations on selecting a Heat & Glo wood burning
fireplace. The Heat & Glo fireplace you have selected is
designed to provide the utmost in safety, reliability, and
efficiency.
As the owner of a new fireplace, you'll want to read and
carefully follow all of the instructions contained in this
Owner's Manual. Pay special attention to all Cautions and
Warnings.
Homeowner Reference Information
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number: __________________________________________ Location on appliance: ____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
Listing Label Information/Location
O-T L Portland
Tested and
Listed by Oregon USA
C US
OMNI-Test Laboratories, Inc.
OMNI-Test Laboratories, Inc.
Report #061-S-40-2
TESTED TO
UL 127, ULC-S610-M87
LISTED FIREPLACE, SOLID FUEL TYPE, ALSO SUITABLE FOR MANUFACTURED
HOME INSTALLATION. (UM) 84 HUD. "For Use with Solid
Install and use only in accordance with manufacturer's installation, venting and operating instructions.
Any area incorporating warm or cold air ducts shall be enclosed in accordance with the manufacturer's
installation instructions.
Contact Your Local Building Or Fire Officials Or Authority Having Jurisdiction About Restrictions,
Installation Inspection And Permits Required In Your Area.
WARNING - For Manufactured Homes: Do not install in a sleeping room. An outside combustion air
inlet must be provided and unrestricted while unit is in use. The structural integrity of the manufactured
home floor, ceiling and walls must be maintained. The fireplace needs to be properly grounded to the
frame of the manfactured home.
Components required for installation: HTI SLSeries Pipe, Termination Cap, Hearth Extension and required
accessory Chimney Air Kit Part CAK4A.
Do not connect this unit to a chimney serving another appliance.
DANGER: Risk of electrical shock. Disconnect power supply before servicing.
Electrical Rating: 115 VAC <3.0 AMPS 60 Hz
Do not use grate or elevate fire. Build wood fire directly on firebrick.
Do not overfire. If heater or chimney connector glows, you are overfiring.
Do not use a fireplace insert or other products not specified for use with this product.
WARNING - THIS FIREPLACE HAS NOT BEEN TESTED WITH AN UNVENTED GAS LOG SET OR ANY LOG SET.
TO REDUCE RISK OF FIRE OR INJURY, DO NOT INSTALL AN UNVENTED GAS LOG SET OR ANY LOG SET INTO
FIREPLACE.
Must provide a source of air to prevent air starvation from combustion which could result of high levels of
carbon monoxide.
Replace glass only with 5mm ceramic available from your dealer.
Optional Fire Screen Part Mesh-EPA, may be used ONLY in USA
U.S. ENVIRONMENTAL PROTECTION AGENCY - Certified to comply with July 1990 particulate emission standards.
Mfg by:
www.heatnglo.com
Page 2
Read this manual before installing or operating this appliance.
Please retain this owner's manual for future references.

Congratulations

A division of Hearth & Home Technologies Inc.
800 West Jefferson, Lake City, MN 55041
www.heatnglo.com
Wood Fuel Only."
2011 2012 2013 Jan Feb Mar Apr May June July Aug Sept Oct. Nov. Dec.
DO NOT REMOVE THIS LABEL
Heat & Glo • NorthStar EPA Fireplace • 480-1081E
This Owner's Manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
Your new Heat & Glo wood burning fireplace will give you
years of durable use and trouble-free enjoyment. Welcome
to the Heat & Glo family of fireplace products!
We recommend that you record the following pertinent
information about your appliance.
The model information regarding your specific appliance can
be found on the rating plate usually located in the control
area of the appliance.
Model:
NorthStar
E C F
PA ERTIFIED IREPLACE
Minimum Clearances To Combustible Material
Chimney sections at any level require a 2" (51mm) minimum
air space clearance between the framing and chimney section.
WITHIN ENCLOSURE AREA
Appliance to backwall
Appliance to sidewall
Duct boots to framing
Top standoffs to header
EXPOSED SURFACES
Faceplate to sidewall
Remote outlet air grills to ceiling
MANTEL
Mantel from base of fireplace
Maximum mantel depth
FLOOR PROTECTION
Combustible flooring 20" (508mm) in front of and 8" (203mm) to
either side of the fuel opening must be insulated with
non-combustible floor protection with a minimum thickness of 1"
(25mm) and ("k" value = 0.43).
In Canada: The hearth extension must be installed according to
the installation instructions.
Made in U.S.A
Serial No / Numéro De Série
009
1" (25mm)
1" (25mm)
0" (0mm)
0" (0mm")
16" (406mm)
12"(305mm)
60" (1524mm)
12" (305mm)
480-1110
4/20/11