Battery Replacement; Specifications - Tripp Lite SmartPro 2U Rackmount SMART1400RM2U Owner's Manual

Smartpro 2u rackmount 120v input/output ups systems

Hide thumbs Also See for SmartPro 2U Rackmount SMART1400RM2U:

Owner's manual (36 pages)

Table of Contents

Available languages

200212046 93-2107 SmartPro 2U Owner's Manual.qxd

Battery Replacement

Under normal conditions, the original batteries in your UPS will

last many years. Battery replacement should be performed

only by qualified service personnel. When replacing the

batteries, qualified service personnel should refer to

"Battery Warnings" in the Safety section and use the following

procedure. The batteries are designed for hot-swap replacement,

but some users may wish to put the UPS in the OFF mode

and disconnect equipment before proceeding. Note:

Batteries cartridges are heavy. Replacement may require an

assistant.

1. Unscrew the six screws on the front face of the unit and remove the front panel. Allow it to dan-

gle by the ribbon cable connecting the LED panel to the UPS.

2. Slide the internal battery cartridges partially out of the UPS towards the front until their electri-

cal connection (A) may be disconnected.

3. Remove batteries from the UPS completely and dispose of them properly.

4. Examine the detailed connection diagram on the inside surface of the UPS system's front panel.

5. Connect replacement batteries exactly according to the diagram, making sure that the input and

output cables (A) are connected as before, black to black and red to red. Reassemble the UPS by

reversing the steps above. Note: your new batteries should be allowed to charge for 2-4 hours

before they support a load.

Specifications

Model:

Series:

Output Capacity (VA/Watts):

Battery Runtime in Minutes

(Half Load/Full Load):

Battery Recharge Time:

Approvals:

Model:

Series:

Output Capacity (VA/Watts):

Battery Runtime in Minutes

(Half Load/Full Load):

Battery Recharge Time:

Approvals:

*Battery Runtime for these models can be increased with the addition of optional external battery packs. Adding external battery packs will also increase recharge time.

All Models: Input Voltage (120V); Input Frequency (60 Hz); Voltage-Regulated Output Voltage Range (120V ±9%); On-Battery Output Voltage Range (120V ± 5%);

Output Waveform Line Mode (filtered sinewave); Output Waveform Battery Mode (PWM sine wave); AC Surge Suppression (exceeds IEEE 587 Cat. A & B stan-

dards); AC Noise Attenuation (>40 dB); AC TVSS Protection Modes (H to N, H to G, N to G); Compatible Battery Packs (BP48V242U and BP48V603U).

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the inter-

ference at his own expense.

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

SMART1400RM2U

SMART1500RMXL2U

AGSM1400Y2U29

1400/940

30+/12+*

2-4 hrs.*

UL, cUL, NOM

SMART2200RMXL2U

SMART2600RM2U

AGSM2200Y2U29