The Information Mode/Demo Mode - ProForm 615 User Manual

Follow your progress with the LED track and
8
the four displays.
See step 5 on page 10.
Measure your pulse, if desired.
9
See step 6 on page 11.
When the program is finished, remove the
10
key.
Step onto the foot rails and remove the key from
the console. Keep the key in a secure place.
Note: If the displays and various indicators
on the console remain lit after the key is re-
moved, the console is in the ÒdemoÓ mode.
Refer to the instructions at the right and turn
off the demo mode.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position.

THE INFORMATION MODE/DEMO MODE

The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also
allows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
To select the information mode, hold down the STOP
button while inserting the key into the console. When
the information mode is selected, the following informa-
tion will be shown:
The DISTANCE/LAPS
display will show the total
number of miles that the
walking belt has moved.
The TIME/INCLINE/SEG
TIME display will show the
total number of hours the
treadmill has been used.
An ÒE,Ó for english miles, or an
ÒM,Ó for metric kilometers, will
appear in the SPEED/ MIN-
MILE display. Press the
SPEED button to change
the unit of measurement.
18
IMPORTANT: The
CALS/FAT CALS/PULSE
display should be blank. If
a ÒdÓ appears in the display,
the console is in the ÒdemoÓ
mode. This mode is intended
to be used only when a tread-
mill is displayed in a store.
When the console is in the
demo mode, the power cord
can be plugged in, the key
can be removed from the
console, and the displays and
indicators on the console will
automatically light in a preset sequence, although the
buttons on the console will not operate. If a ÒdÓ appears
in the CALS/FAT CALS/PULSE display when the in-
formation mode is selected, press the SPEED
button so the CALS/FAT CALS/PULSE display is
blank.
To exit the information mode, remove the key from the
console.
OPTIONAL HAND WEIGHTS
Optional hand weights let
you include upper-body ex-
ercise in your workouts.
The hand weights fit into
convenience holders in the
console. To purchase the
optional hand weights,
call the Customer Service
Department (see the back
cover of this manual).
OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor adds even more
features to the console. The chest pulse sensor offers
hands-free operation and continuously monitors your
heart rate during your workouts. To purchase the
optional chest pulse sensor, call our Customer
Service Department (see the back cover of this
manual).
3. Locate the plastic tie in the post on the left Upright (82).
Hold a Handrail Extension (85) in the position shown.
Insert the plastic tie into the Handrail Extension as you
insert the Handrail Extension into the post. Attach the
Handrail Extension with three Screws (76). Note: The
plastic tie is tied to the Hand Pulse Wire (124). Be
careful to avoid damaging the Hand Pulse Wire. The
Hand Pulse Wire is used with the optional chest pulse
sensor (see page 18).
Slide a Handrail Foam Grip (110) onto the Handrail
Extension (85). (If it is difficult to slide on the Foam Grip,
place a small amount of warm water and dish soap in the
Foam Grip.) There are one or two holes in the bottom of
the Foam Grip. Press a Plastic Fastener (47) into each
hole.
Attach the other Handrail Extension and Handrail Foam
Grip to the right Upright (not shown). Note: There is not a
wire harness in the right Upright.
4. Make sure that the Lock Knob Sleeve (111) is fully in-
serted into the left Upright (82).
Remove the Lock Knob (102) from the Lock Pin (115).
Make sure that the Lock Pin Collar (113) and the Spring
(112) are on the Lock Pin. Insert the Lock Pin into the
left Upright (82) and tighten the Lock Knob onto it.
5. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a
secure place. The allen wrench is used to adjust the walking belt (see page 21). To protect the floor or carpet
from damage, place a mat under the treadmill.
3
76 Post
124
Plastic Tie
110
76
85
82
47
4
82
112
102
113
115
111
7