Audyssey Settings - Denon AVR-1911 Owner's Manual

Setting items
Height Gain Low : Reduce the front height channel volume.
Control the front height Mid : Front height channel sound is output with standard sound volume.
channel volume. High : Increase the front height channel volume.
NOTE
"Height Gain" is displayed for the following settings.
• When "Amp Assign" (vpage 54) is set to "Front Height".
• When the "Speaker Config." – "Front Height" setting (vpage 55) is set
to other than "None".
• When surround mode is "PLgz" or the PLgz decoder is used.
Subwoofer ON : The subwoofer is used.
Turn subwoofer output on OFF : The subwoofer is not used.
and off.
NOTE
This can be set when the surround mode is "DIRECT" or "PURE DIRECT"
(vpage 72, 73), and the "Subwoofer Mode" (vpage 55) is "LFE+Main".
Default Yes : Reset to the defaults.
The "Surround Parameter" No : Do not reset to the defaults.
settings are returned to the
default settings.
Tone
Adjust the tonal quality of the sound.
Setting items
Tone Control ON : Allow tone adjustment (bass, treble).
Set the tone control function OFF : Playback without tone adjustment.
to ON and OFF.
"Tone Control" can be set when "Dynamic EQ" (vpage 52) is set to
"OFF".
NOTE
• "Tone Control" settings are not reflected to ZONE2.
• The tone cannot be adjusted in the direct mode.
Bass –6dB – +6dB (0dB)
Adjust low frequency range
"Bass" can be set when "Tone Control" is set to "ON".
(bass).
Treble –6dB – +6dB (0dB)
Adjust high frequency range
"Treble" can be set when "Tone Control" is set to "ON".
(treble).
Remote control operation
buttons
Setting details
Default settings are underlined.
Setting details
Move the cursor
(Up/Down/Left/Right)

Audyssey Settings

Set MultEQ ® , Dynamic EQ ® and Dynamic Volume™. These can be selected after Audyssey ® Auto Setup
has been performed. For additional information on Audyssey technology, please see page 76.
NOTE
If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,
you may not be able to select Dynamic EQ/Dynamic Volume, and "Run Audyssey" may be displayed.
In this case, either perform Audyssey Auto Setup over again or perform "Restore" (vpage 10) to return to
the settings after Audyssey Auto Setup was run.
Setting items
MultEQ Audyssey : Optimize the frequency response of all speakers.
Select one equalizer from Audyssey Byp.L/R : Optimize frequency response of speakers except
three modes. MultEQ front L and R speakers.
corrects both time and Audyssey Flat : Optimize frequency response of all speakers to flat
frequency response response.
problems in the listening Manual : Apply frequency response set with "Manual EQ" (vpage 53).
area based on Audyssey OFF : Turn "MultEQ" equalizer off.
Auto Setup calibration. We
recommend "Audyssey".
• "Audyssey",
MultEQ is the prerequisite
"Audyssey Flat" can be selected after Audyssey
function for Dynamic EQ
Auto Setup has been performed. "Audyssey" is
and Dynamic Volume.
automatically selected after performing Audyssey
Auto Setup. When "Audyssey", "Audyssey Byp.
L/R" or "Audyssey Flat" is selected,
illuminates.
• After running Audyssey Auto Setup, if the
Speaker Configuration, Distance, Channel
Level, and Crossover Frequency have changed
without increasing the number of speakers
measured, only
MULTEQ
• Pressing
or the main unit makes this setting.
NOTE
• "MultEQ" and "Manual" cannot be selected when "EQ Customize" is
set to "Not Used" (vpage 58).
• When using headphones, "MultEQ" is automatically set to "OFF".
Confirm the setting
Audio Adjust
Default settings are underlined.
Setting details
"Audyssey Byp. L/R" and
illuminates.
on the remote control unit
Return to previous menu
ENGLISH
51