Electronic Clock; Por783 Programmable Controller - Westinghouse POR663 Owner's Manual

Models POR667, PORS668L/R, POR668,
PGR659, PXR698, PDR790, PDR794
touch control electronic clock
General features
Your touch control clock has the following features:
• T imer – allows you to set a countdown time that will beep
when the set time has elapsed�
• C ooking duration – You can set a cooking duration. A
timer will count down the preset cooking time, beep when
the time has elapsed and turn the oven off�
• E nd cooking time – you can set a cooking finish time. A
timer will count down the preset cooking time, beep when
the finish time has been reached and turn the oven off�
• D elayed start cooking time – You can combine the
cooking time and stop cooking time to switch the oven on
and off at a specific time during the day�
NoTe: Your touch control clock only operates with your
main oven.
Setting the time of day
You must set the time of day before you can operate your
appliance� When power is supplied to your oven "12�00"
will be displayed and the "clock" indicator will flash.
1. T o set the time of day in hours and minutes, press – or +.
5 seconds after the last change, the "clock" indicator
will disappear, confirming the time has been set�
NoTe: The clock has a 24-hour display.
Change the time of day (daylight saving)
1� Press "mode" until the "clock" indicator begins flashing.
2. P ress – or + to change the time. 5 seconds after the last
change, the "clock" indicator will disappear, confirming
the time has been set�
Setting the timer
1� Press "mode" until the "timer" indicator begins flashing.
2. S et the countdown time you want by using – and +. 5
seconds after the last change the "timer" indicator will
stop flashing, confirming the timer has been set.
3. To stop the beeper, press –, + or "mode".
Setting the cooking duration
1� Check the clock displays the correct time of day�
2� Select the desired oven function and temperature�
The oven indicator light will glow and the heating source
will come on�
3� Press "mode" until the "cook time" indicator
begins flashing.
ELECTRIC CLOCK
16
4. S et the cooking duration you want by using – or +. 5
seconds after the last change, the "cook time" indicator
will stop flashing, and the time of day will be displayed.
NoTe: Do not forget to add preheating time if necessary.
Setting the cooking end time
1� Check the clock displays the correct time of day�
2� Select the desired oven function and temperature� The
oven indicator light will glow and the heating source will
come on�
3� Press "mode" until the "end time" indicator begins
flashing.
4� Enter the time of day you want to finish cooking by
pressing – or +. 5 seconds after the last change, the "end
time" indicator will stop flashing and the current time of
day will be displayed�
Setting the delayed start cooking time
1� Program the "cook time" and "end time" as described
in the relevant sections� Once both the "cook time" and
"end time" have been set, the "cook time" and "end time"
indicators will stop flashing and the current time of day
will be displayed�
To check or cancel settings
1� To check your settings, press "mode" until the setting you
want is displayed. A red light will flash next to the mode
(cook time, end time etc) that is currently on display�
2. T o cancel "delayed start" press "mode" until a light flashes
next to "end time". Press and hold "–" until the clock no
longer reverses ("0:00" and you will hear a beep). If you
have left the temperature and function knobs at a setting
the oven will start once the "end time" light stops flashing.
3. T o cancel "auto shut off" press "mode" until a light flashes
next to "cook time". Press and hold "–" until the clock no
longer reverses ("0:00" and you will hear a beep)� This
automatically cancels "delayed start". If you have left the
temperature and function knobs at a setting, the oven will
start once the "cook time" light stops flashing. Because
you have cancelled "auto off" the oven will continue to
heat until you manually turn it off�
On completion of cooking
The oven will turn off, the timer will beep and the "end time"
and/or "cook time" indicators will flash.
1� Turn the function and temperature controls to the off
position�
2. Press "+" or "–" or "mode" to stop the timer from beeping.
Switching the clock display ON and Off
1. P ress together "+" and "–" for 2 seconds to switch 'off'
the display�
2. P ress together "+" and "–" for 2 seconds to switch the
clock display 'on' again�
NoTe: If a timer mode is set, then it is not possible to switch
the display off.
touch control
Setting the time of day
After the appliance has been electrically connected the "set
clock" symbol and "timer arrow will flash on the clock
display�
1. T o set the time of day in hours and minutes press the – or
+. 5 seconds after the last change the "timer arrow"
will disappear, confirming the time has been set�
NoTe: The clock has a 24-hour display.
Change the time of day (daylight saving)
1� Switch off the appliance by pressing "On / Off"�
2� Press "Timer" as many times as necessary until the "set
clock" symbol and "timer arrow" flash on the clock
display�
3. P ress "+" or "–" to change the time. 5 seconds after the
last change the "set clock" symbol and "timer arrow"
will disappear, confirming the time has been set�
Setting the oven function
1� Switch on the appliance by pressing the "On / Off"� The
oven lights will light�
2� Press the "Function" as many times as necessary until
the desired function appears� The suggested cooking
temperature appears in the display and the degrees
symbol "°" flashes. If the suggested temperature is not
changed within approximately 5 seconds the degrees
symbol "°" stops flashing and the oven begins to heat.
The suggested temperature display is replaced with the
oven centre temperature and a thermometer icon� The
thermometer icon rises slowly, indicating the degree to
which the oven is currently being heated�
Changing the oven temperature
1. P ress the – or +, to decrease or increase the temperature.
N oTe: The temperature can only be adjusted when the
degrees symbol "°" is flashing. The temperature setting
changes in increments of 5°C. To change the temperature
after the degrees symbol "°" stops flashing, press the
"Function" and then press the – or + to change the
temperature.
Setting the cooking time
1� Select the desired oven function and cooking temperature�
2� Press the "Timer" as often as necessary, until the "cook
time" symbol appears�
3. S et the desired cooking time by using the – or +, whilst
the "timer arrow" is flashing. After 5 seconds from the
last time adjustment the "timer arrow" will disappear
and your appliance is now programmed�
4� When the set time has elapsed, a signal will sound� To
stop the signal, press "+" or "–".
Setting the stop time
1� Select the desired oven function and cooking temperature�
2� Press the "Timer" as often as necessary, until the "end
time" symbol appears flashing.
3. S et the desired switch-off time using the – or + whilst the
"timer arrow" is flashing. After 5 seconds from the last
time adjustment the "timer arrow" will disappear and
your appliance is now programmed�
4� When the set time has elapsed, a signal will sound� To
stop the signal, press "+" or "–".
Setting the delayed start cooking time
The "cook time" and "stop time" functions can be combined
to switch the oven on and off at a
specific time during the day�
1� Select the desired oven function and cooking temperature�
2� Press "Timer" as often as necessary, until the "cook time"
symbol appears�
3. S et the desired cooking time by using – or + , whilst the
"timer arrow" is flashing.
4� Press "Timer" as often as necessary, until the "end time"
symbol appears flashing
5. S et the desired switch-off time using the – or + whilst the
"timer arrow" is flashing. The "cook time" and "end
time" arrows are lit to confirm that the oven has been
programmed�
On completion of cooking
When the set time has elapsed, a signal will sound for
1 minute, the oven will switch off and the remaining time
indication "0�00" will appear on the display�
1. To stop the signal, press "+" or "–".
Setting the minute minder
For setting a countdown period� When the period of time has
elapsed, an audible signal is sounded�
NoTe: This feature has no effect on the oven operation.
1� Press "Timer" as often as necessary, until the "minute
minder" symbol appears flashing. Set the desired
length of time using – or + whilst the "timer arrow"
flashing. After 5 seconds from the last time adjustment the
"timer arrow" will disappear and the minute minder
has been set� Once the set time has elapsed, a signal
will sound for 1 minute� The time indication "0�00" and
a flashing "minute minder" symbol will appear on the
display�
2. To stop the signal, press "+" or "–".
17
is
POR783
PROGRAMMABLE
CONTROLLER