Sharp HT-SB20 Operation Manual

ENGLISH
MODEL
HT-SB20
HT-SB30
SOUND BAR HOME THEATER SYSTEM
OPERATION MANUAL
ON/
STAND-BY
MUTE
SOUND MODE NEWS
MUSIC
CINEMA
INPUT
SURROUN D
BYPASS
TV
CH
VOL
VOL
322AWSA
RRMCGA
(HT-SB30 only)
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by SHARP is under license. Other
trademarks and trade names are those of their respective owners.
Note: This product is recommended for fl at panel TV (LED, LCD and plasma).
Caution: Before operating this product, refer "IMPORTANT SAFEGUARDS AND
WARRANTY" at the reverse page of English operation manual.
*TINSZB425AWZZ2-*|
Printed in Malaysia
1
13A R AS
TINSZB425AWZZ
Placing the sound bar
Installation image: Notes:
● Remove the protective fi lm covering the sound
bar before turning on the system.
TV
The front panel of the sound bar is not
●
removable.
Place the
sound Caution:
bar as
● Do not change the installation direction when
shown.
the sound bar is turned on.
Do not stand or sit on the sound bar as you
●
may be injured.
VCR DVD player
Falling prevention
Safety wires (not supplied) are useful to prevent the sound bar from falling.
●
E-4
Remote control
Precautions for battery use:
■
Battery installation
Remove the battery if the sound bar will
This product contains a CR Coin not be used for a long period of time.
This will prevent potential damage due
Lithium Battery which contains Per-
chlorate Material – special handling to battery leakage.
may apply, California residents, see
Caution:
www.dtsc.ca.gov/hazardouswaste/per-
Do not use rechargeable battery
●
chlorate/
(nickel-cadmium battery, etc.).
Danger of explosion if battery is in-
●
1
While pushing the locking tab to- correctly replaced.
wards the center of the remote con-
● Replace only with the same or
trol, slide out the battery holder.
equivalent type.
Batteries (battery pack or batteries
●
Back of
installed) shall not be exposed to ex-
remote control
cessive heat such as sunshine, fi re
or the like.
● Installing the battery incorrectly may
cause the sound bar to malfunction.
Locking Notes concerning use:
tab Replace the battery if the operating
●
2 Remove the old battery from the distance is reduced or if the opera-
battery holder, insert the new bat- tion becomes erratic. Purchase "CR
tery and then slide the battery hold- 2025", coin lithium battery.
er back into the remote control. Periodically clean the transmitter on
●
the remote control and the sensor
Battery holder Positive (+)
on the sound bar with a soft cloth.
side up
Exposing the sensor on the sound
●
Polarity
bar to strong light may interfere with
(+) symbol
operation. Change the lighting or the
Battery type direction of the sound bar if this oc-
curs.
Locking tab
Keep the remote control away from
●
moisture, heat, shock, and vibra-
tions.
E-8
Listening to Bluetooth enabled devices (for HT-SB30) (continued)
■ Listening to the sound ■ To fi nish listening
Check that:
Perform any of the followings.
● The source device Bluetooth functionality is ON.
- Terminate the Bluetooth connection on the audio
Pairing of this sound bar and the source device
● source device.
is completed.
Refer the operating manual supplied with the
Any device connected to the AUDIO IN socket
● device.
is turned off.
- Turn off the Bluetooth stereo audio source
device.
1 Press the ON/STAND-BY button to turn the
- Turn off this sound bar.
power on.
2
Press the INPUT button to select Bluetooth
Note:
function.
The volume of this sound bar may not be controlled
3
Start the Bluetooth connection from the
as intended depending on the device.
Bluetooth stereo audio source device.
4 Start playing on the Bluetooth stereo audio
Bluetooth operation buttons
source device.
(remote control only)
Notes:
If the source device has an extra bass function Press the button to play or pause.
or equalizer function, set them to off. If these
functions are on, sound may be distorted.
Press the button to skip up.
Notes:
You need to make the Bluetooth connection Press the button to skip down.
●
again if:
- the sound bar is not turned on.
- the source device is not turned on, or its Blue-
tooth functionality is off or is in sleep mode.
● If both the Bluetooth connected device and the
one connected to the AUDIO IN are played
simultaneously, only the Bluetooth sound can
be heard.
E-12
HT-SB30_EN_SPECIAL_NOTES_A2.indd1 1 HT-SB30_EN_SPECIAL_NOTES_A2.indd1 1
Accessories
The following accessories are included.
Remote control x 1 AC/DC adaptor x 1 AC power cord x 1
(RRMCGA326AWSA: HT-SB20) (RADPAA096AWZZ) (QACCDA005AWZZ)
(RRMCGA322AWSA: HT-SB30)
Audio cable x 1 Pattern paper x 1
(QCNWGA087AWPZ) (TCAUHA034AWZZ)
The illustrations printed in this manual are for the model HT-SB30.
Controls and indicators
■
Front Panel (HT-SB20)
1 2 3 4 5 6 7 8
1. On/Stand-by 7. Volume Up Button
Indicator 8. Remote Sensor
2. On/Stand-by 9. Left Channel
Button Speakers
3. Surround Button 10. Right Channel
SOUND BAR HOME THEATER SYSTEM HT-SB20 4. Surround Indicator Speakers
5. Volume Indicator
6. Volume Down
Button
SOUND BAR HOME THEATER SYSTEM HT-SB20
9 10
■ Front Panel (HT-SB30)
1 2 3 4 5 6 7 8 9 10
1. On/Stand-by 10. Remote Sensor
Indicator 11. Left Channel
2. On/Stand-by Speakers
Button 12. Right Channel
3. Input Button Speakers
SOUND BAR HOME THEATER SYSTEM HT-SB30
4. Pairing Button
5. Pairing Indicator
6. Surround Indicator
7. Surround Button
8. Volume Down
Button
SOUND BAR HOME THEATER SYSTEM HT-SB30
9. Volume Up Button
11 12
E-1
■ When mounting on the wall
Screw eye (not supplied)
Safety wires (not
supplied)
SOUND BAR HOME THEATER SYSTEM HT-SB30
Sound bar
Wall
■ When placing on the shelf/table
Sound bar
Screw eye
Safety
(not supplied)
Rack/
wires
table
(not
supplied)
Screw eye
(not supplied)
E-5
General control
■ ■
To turn the power on Sound Mode
Press the ON/STAND-BY button.
Remote control operation:
The STAND-BY indicator turns BLUE.
Press the desired sound mode button
Note: on the remote control.
If the power does not turn on, check whether
HT-SB20
the power cord is plugged in properly.
The VOLUME indicator: blinking
To set the sound bar to stand-by mode:
Press the ON/STAND-BY button again. The
HT-SB30
STAND-BY indicator turns RED.
The SURROUND indicator: blinking
■ Volume auto fade-in
CINEMA (for cinema sound effect)
If you turn off and on the sound bar again,
MUSIC (for standard sound effect)
volume will start at lower level and gradually
NEWS (for news)
increase to the last set level.
BYPASS (for fl at sound effect)
■ Volume control
■ Function
Sound bar operation:
Press volume up (VOLUME + ) to increase
HT-SB20
the volume and press volume down (VOL-
UME – ) to decrease the volume. When the sound bar is connected to the TV/
DVD, etc., the AUDIO IN function is ready
Remote control operation:
to be used.
Press the VOL + button to increase the
volume and the VOL – button to decrease
HT-SB30
the volume.
When the INPUT button is pressed, the input
Note:
source will change.
When volume is maximum or minimum:
1 Audio In Function - the pairing indicator turns
off.
HT-SB20
2 Bluetooth Function - the pairing indicator
The VOLUME indicator: blinking
turns blue.
Note:
HT-SB30
The backup function will protect the memorized
The SURROUND indicator: blinking
function mode for a few hours should there be
a power failure or the AC power cord becomes
■ disconnected.
Muting
Auto power on function:
The volume is muted temporarily when pressing
When stand-by indicator is VIOLET, the sound
●
the MUTE button on the remote control. Press
bar will automatically power ON if it detects
again to restore the volume.
audio signal from connected equipment,
unless it is turned off manually (STAND-BY
■
Surround
indicator turns red).
When the SURROUND button is pressed, the Auto power off and auto detect signal:
The sound bar will automatically go to stand-
SURROUND sound is ON. (SURROUND indicator ●
turns ORANGE) by mode (STAND-BY indicator turns violet) if
no audio signal is detected within 20 minutes.
E-9
Troubleshooting chart
Many potential problems can be resolved by the
Bluetooth sound Is the sound bar
●
owner without calling a service technician.
is interrupted or too near to a device
If something is wrong with this product, check the
distorted. that generates
following before calling your authorized SHARP
(HT-SB30) electromagnetic
dealer or service center.
radiation?
Is there any obstacle
●
between the sound
■ General
bar and the Bluetooth
stereo audio source
Symptom Possible cause
device?
No sound is heard. Is the input signal
●
(selection) set
■ Remote control
properly?
Is the volume level set
●
to minimum?
Symptom Possible cause
Is muting activated?
●
The remote control ● Is the battery polarity
● Are the connections
does not operate correct?
made correctly?
properly. ● Is the battery dead?
Is the sound bar too
●
Is the distance or angle
●
far from the Bluetooth
incorrect?
stereo audio source
● Are there any
device? (HT-SB30)
obstructions in front of
● Is the sound bar paired
the sound bar?
with the Bluetooth
● Is there a strong light
stereo audio source
shining on the remote
device? (HT-SB30)
sensor?
Noise is heard ● Move the sound
● Is the remote control
during playback. bar away from any
for another equipment
computers or mobile used simultaneously?
phones.
The sound bar ● Is the AC power cord
When a button Set this sound bar to
● cannot be turned of the sound bar
is pressed, the the stand-by mode and
on with the remote plugged in?
sound bar does not then turn it back on.
control. ● Is the battery inserted?
respond. If the sound bar still
●
TV cannot be ● Depending on the
malfunctions, reset it.
operated with the model, some or all
(Refer to page 7.)
remote control. functions may not be
The power is not Is the sound bar
● operable using the
turned on. unplugged? (Refer to
remote control of this
page 10)
sound bar. In this case,
The protection circuit
● use the remote control
may be activated.
supplied with the TV.
Unplug and plug in the
power cord again after
5 minutes or more.
E-13
Controls and indicators (continued)
■ Rear Panel
1
1. DC In Jack
2. Audio In Jack
2
1 ■
Remote Control
ON/
MUTE STAND-BY
2 12 1. Remote Control Transmitter
SOUND MODE
2. Mute Button
CINEMA MUSIC NEWS
3 13
3. Cinema (Sound Mode) button
4
4. Music (Sound Mode) button
BYPASS SURROUND INPUT
5
14
5. Surround Button
6
TV 6. Bypass (Sound Mode) button
7. TV Operation Buttons
7 VOL CH 8. Bluetooth Pairing Button (HT-SB30 only)
9. Bluetooth Play/Pause Button (HT-SB30
only)
8
10. Bluetooth Skip Up Button (HT-SB30 only)
9
15
VOL 11. Bluetooth Skip Down Button (HT-SB30
10
only)
11
12. On/Stand-by Button
13. News (Sound Mode) button
14. Input Button (HT-SB30 only)
15. Volume Up/Down Buttons
RRMCGA322AWSA
Note:
Remote control Plastic shield
Before using remote control, please remove plastic
shield at battery holder.
Battery holder
TV Operation Buttons (Only SHARP TV):
On/Stand- Sets the TV power to Input Select Press the button to
by Button "ON" or "STAND-BY". Button (TV) switch the input source.
Volume Up Turn up/down the TV Channel Up and Switch up/down the TV
and Down volume. Down Buttons channels.
VOL CH
Buttons
Note: ● Some models of SHARP TV may not be operable.
● SHARP TV remote control will not work with HT-SB20/HT-SB30 system.
E-2
Sound bar connections to TVs
Caution:
Turn off all other equipment before making any connections.
Notes:
● To connect to TV, use Audio IN terminals located at the rear of the sound bar.
● Refer the operation manual of the equipment to be connected.
● Fully insert the plugs to avoid fuzzy pictures or noises.
● In some cases, a small background noise could emit from the sound bar, when you
use the RCA audio output terminal connection from a TV-Set/DVD/Blu-ray Disc
Player. In such case, please change the connection to the headphone terminal
connection. This effect depends on the used TV/DVD/Blu-ray Disc Player-Brand,
model and age, and it is not a quality matter from the sound bar.
● If the TV volume is continuously at low level, the sound bar will automatically
power off. Increase the TV output volume to enjoy the sound from the speaker.
■ Connecting a TV, or DVD player, etc.
If the TV/monitor has an audio output, connect it to the Audio IN jack on the rear
of the sound bar.
HT-SB30
To select AUDIO IN function:
Press INPUT button repeatedly.
To select Bluetooth function:
Press INPUT button repeatedly. (PAIRING indicator turns blue.)
TV
To audio output terminals
or
To HEADPHONE
terminal
Blu-Ray/DVD player/
Digital Tuner
Audio cable
Audio cable
(not supplied)
To AUDIO
IN jack
Sound bar
E-6
Listening to Bluetooth enabled devices (for HT-SB30)
■ Audio stream
About Bluetooth technology
ON/STAND-BY SOURCE PAIRING SURROUND VOLUME - +
SOUND BAR HOME THEATER SYSTEM HT-SB30
Bluetooth wireless technology is a short-range radio
technology that enables wireless communication
Bluetooth mobile phone or other
between various types of digital devices, such Bluetooth Stereo audio source device
as mobile phone or computer. It operates within
a range of about 10 meters (30 feet) without the
■ Pairing Bluetooth devices
hassle of having to use cables to connect these
Bluetooth devices need to be initially paired fi rst
devices. Since the Bluetooth technology does not
require line of sight between the communicating before they can exchange data. Once paired, it is
not necessary to pair them again unless:
devices, it is not necessary to line up the transmit-
ting device and the receiver, as in the case of infra ● pairing is made with more than 8 devices.
Pairing can only be made one device at
red technology.
a time. This sound bar can be paired to a
Communication System and Bluetooth Profi le
maximum of 8 devices. If subsequent device
of this sound bar
is paired, the oldest device paired, will be de-
There are many available Bluetooth Profiles
leted and replaced with the new one.
describing the basic communication methods,
this sound bar is reset. All pairing information
●
specifi c functions and uses, to enable communica-
is deleted when sound bar is reset.
tion between devices.
● pairing information is deleted while repairing, etc.
This sound bar supports the following:
On indicators
Communication System: Bluetooth Specifi cation
Status PAIRING indicator (blue)
version 2.1 Bluetooth + Enhanced Data Rate
(EDR) Profi le : A2DP (Advanced Audio Distribu-
Unconnected Blinks
tion Profi le)
Pairing mode Blinks quickly
A2DP enables audio streaming from an A2DP
Connected Lights up
equipped Bluetooth stereo audio source device
(eg mobile phone) to this sound bar. By convert-
ing wireless stereo audio signal to analogue audio
signal, you can enjoy listening to the sound through
this speaker system.
AVRCP (Audio/Video Remote Control Profi le) is a
technology that allows a single remote control to
control all Bluetooth enabled Audio Video equip-
ment to which a user has access.
Notes when using unit with a mobile phone
● This unit cannot be used to talk over the tele-
phone even when there is a Bluetooth con-
nection made to a mobile phone.
● Please refer to the operating manual supplied
with the mobile phone for details on operation
of your mobile phone while transmitting the
sound using a Bluetooth connection.
E-10
Troubleshooting chart
■ Error indicators and
Condensation
warnings
Sudden temperature changes, storage or operation
in an extremely humid environment may cause con-
When you fail to perform operations properly, the fol-
densation inside the cabinet or on the transmitter
lowing messages are displayed on the sound bar.
on the remote control.
Condensation can cause the sound bar to malfunc-
Display Meaning
tion. If this happens, leave the power on until normal
operation is possible (about 1 hour). Wipe off any When the protection circuit
●
condensation on the transmitter with a soft cloth is activated.
Power indica-
before operating the sound bar.
tor (blinks red)
■ Factory reset, clearing all
(*): Should the same message appear even if
setting
the sound bar is unplugged and plugged in
or is set to the stand-by mode and on again,
Make sure to disconnect all audio input cables
contact your local dealer where you purchased
attached to the sound bar before performing the
the sound bar.
factory reset.
1. Unplug the AC power cord.
2. HT-SB20
Press and hold ON/STAND-BY button
and the SURROUND button and plug the
AC power cord.
HT-SB30
Press and hold ON/STAND-BY button
and the PAIRING button and plug the AC
power cord.
3. Press the ON/STAND-BY button
Caution:
This operation will erase all data stored in
memory.
■ If problem occurs during
operation
When this product is subject to strong external
interference (mechanical shock, excessive static
electricity, abnormal supply voltage due to light-
ning, etc.) or if it is operated incorrectly, it may
malfunction.
If such a problem occurs, do the following:
1
Set the sound bar to the stand-by mode and
turn the power on again.
2 If the sound bar is not restored in the previous
operation, unplug and plug in the sound bar,
and then turn the power on.
E-14
System preparation
To mount the sound bar on the wall 2
Make a hole on the wall following the screw
point marks on the pattern paper by using
Caution:
a drill.
Be very careful to prevent the sound bar [5.07 lbs.
●
(2.3 kg)] from falling when mounting on the wall. 1-1/4" (32 mm)
● Before mounting, check the wall strength. (Do not
put on the veneer plaster or whitewashed wall. The
3/8" (8-9 mm)
sound bar may fall.) If unsure, consult a qualifi ed
service technician.
Mounting screws are not supplied. Use appropri- Wall surface
●
ate ones.
3
Fix a wall mount plug into the hole using
Check all wall mount angle screws for looseness.
●
a hammer, until it is fl ush with the wall
Select a good location. If not, accidents may occur
●
surface.
or the sound bar may get damaged.
SHARP is not responsible for accidents result- 1-1/4" (32 mm)
●
ing from improper installation.
3/8" (8-9 mm)
■ Driving screws
SHARP designed the sound bar so you may hang
Wall surface
it on the wall. Use proper screws (not supplied).
4
See below for size and type. Fasten the screws to the wall as shown below.
(Total screw is 2 pieces)
1/8" (3.2 mm)
Screw using
3/16"
(5 mm)
3/8" (9 mm)
Screwdriver
Wall surface
Min. 7/8" (22 mm)
4.5mm - 5mm
■
Installing the sound bar
Gap from
Wall surface
wall surface
1 Fix the pattern paper to the wall in hori-
zontal position as below.
5
Hang the sound bar onto the screws.
Wall
509 mm
548 mm
surface
44 mm
Pattern paper
(supplied)
E-3
AC power connection
After checking all the connections have
Make sure to unplug the AC power
been made correctly, connect the AC
cord before making any connections.
power cord to the AC power input jack,
then to the AC outlet.
AC/DC Adaptor
■
Using with the AC/DC adaptor
2
Cable
1 Plug the AC power cord into the AC/
DC IN jack
DC adaptor.
(DC 17V)
2 Plug the AC/DC adaptor cable into
the DC INPUT jack on the sound
bar.
AC power cord
3 Plug the AC power cord into an AC
1
AC outlet
outlet.
AC/DC Adaptor
Notes: (AC 100 - 240 V ~ 50/60 Hz)
During power standby, the stand-by
●
indicator turns RED. If ON-STANDBY
button is pressed, the STAND-BY
indicator turns BLUE.
● Unplug the AC/DC adaptor from the
AC outlet if the sound bar will not be
used for a prolonged period of time.
Use only the supplied AC/DC adaptor.
●
Using other AC/DC adaptor may
cause an electric shock or fi re.
E-7
Listening to Bluetooth enabled devices (for HT-SB30) (continued)
ON/STAND-BY PAIRING 5
Select "SHARP HT-SB30" from the source
list. If Passcode* is required, enter "0000".
ON/STAND-BY SOURCE PAIRING SURROUND - VOLUME +
Pairing indicator (blue) on the sound bar will
SOUND BAR HOME THEATER SYSTEM HT-SB30
stop blinking once the sound bar is success-
fully paired with the source device. Pairing
■ Pairing with other Bluetooth
information is now memorized in the sound
source device
bar.
* Passcode may be called PIN Code, Passkey,
1
Press the ON/STAND-BY button to turn the
PIN number or Password.
power on.
6 Start the Bluetooth connection from the
2
Press the INPUT button to select Bluetooth
source device.
function. (PAIRING indicator blinks.)
Some audio source devices may connect with
3
Press and hold the PAIRING button for 1
the sound bar automatically, otherwise follow
second or more.
the instructions in the source device operating
PAIRING indicator blinks quickly. The sound
manual to start connection.
bar is now in pairing mode and is ready to be
paired with other Bluetooth source device.
Notes:
If this sound bar or the source device is turned
Note: ●
Pairing indicator (blue) will stop blinking once off before Bluetooth connection is completed,
pairing will not be completed and the pairing
the sound bar is successfully paired with the
source device. information will not be memorized. Repeat
step 1 onwards to start pairing again.
4 Perform pairing procedure on the source
● To pair with other devices, repeat steps 1 - 5
device to detect this sound bar. (Refer
for each device.
the source device operating manual for
This sound bar can be paired to a maximum
details).
of 8 devices. If subsequent device is paired,
"SHARP HT-SB30" will appear in the detected
the oldest device paired, will be deleted and
devices list (if available) in the source device.
replaced with the new one.
Notes:
● Once a device is ousted or deleted from
Place the devices to be paired within 1 me-
●
the pairing list, the pairing information for
ter (3 feet) of each other when pairing.
the device is also deleted. To listen to the
Some source devices are unable to display
●
sound from the device again, it needs to be
lists of detected devices. To pair this sound
re-paired. Perform steps 1 - 5 to pair the de-
bar with the source device, refer to the
vice again.
source device operating manual for details.
Passcode of this sound bar is fi xed to "0000"
●
and can only be paired with Bluetooth source
device whose passcode is also "0000".
E-11
Maintenance Specifi cations
■ Cleaning the cabinet
As part of our policy of continuous improvement,
SHARP reserves the right to make design and
Periodically wipe the cabinet with a soft cloth.
specification changes for product improve-
Caution: ment without prior notice. The performance
Do not use chemicals for cleaning (petrol, paint specification figures indicated are nominal
●
values of production unit. There may be some
thinner, etc.). It may damage the cabinet fi nish.
deviations from these values in individual unit.
Do not apply oil to the inside of each component.
It may cause malfunctions.
■ General
Power source DC IN 17V 2.8A: AC/DC
adaptor
(AC 100 - 240V ~ 50/60Hz)
ON/STAND-BY SOURCE PAIRING SURROUND - VOLUME +
Power 10W
SOUND BAR HOME THEATER SYSTEM HT-SB30
consumption
Maximum RMS: Total 40 Watts
output power 20 Watts per channel into
6 ohms at 1 kHz, 10% total
harmonic distortion
FTC: Minimum 14 watts
per channel into 3 ohms at
100 Hz to
20 kHz, 1% total harmonic
distortion
Speaker 2-way Speaker System
2-1/4" (5.7cm) Woofer
1" (2.5cm) Soft Dome
Input Analog input (AUDIO IN):
terminals Stereo mini jack Ø 3.5mm
500mV / 47kohms
Frequency 2.4 GHz band (2,400GHz
Band - 2,480GHz)
(HT-SB30)
Compatible A2DP (Advanced Audio
Bluetooth Distribution Profi le), AVRCP
Profi le (Audio/Video Remote Control
(HT-SB30) Profi le)
Bluetooth 2.1 +EDR
Dimensions Width: 37" (940mm)
Height: 2-7/8" (73mm)
Depth: 3-1/4" (83mm)
Weight 5.07lbs. (2.3kg)
E-15
2013-01-07 06:55:01 2013-01-07 06:55:01