SOUND BAR HOME THEATER SYSTEM OPERATION MANUAL Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. HT-SB603 Sound Bar Home Theater system consisting of HT-SB603 (sound bar system) and CP-SW603 (active subwoofer system).
® trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SHARP is under license. Other trademarks and trade names are those of their respective owners. The N Mark is a trademark or registered trademark of NFC Forum, Inc.
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer.
4" (10 cm) This unit should only be used within the range of 41°F - 95°F (5°C - 35°C). SHARP is not responsible for damage due to improper use. Refer all servicing to a SHARP authorised service center. 4" (10 cm)
Page 6
Controls and indicators (continued) Sound Bar Rear Panel 1. IR OUT Terminal 2. HDMI OUT (TV ARC) Jack 3. USB terminal 4. HDMI IN 1 Jack 5. HDMI IN 2 Jack 6. Optical IN Jack 7. Audio IN Terminal 8. AC Power Cord Subwoofer Front view Rear view...
5 6 7 8 9 Remote Control Display remote control 1. TV Operation Button HT-SB603 comes with a wireless display remote control 2. Bluetooth Pairing Button which uses Bluetooth to communicate instead of infra red 3. Display which requires direct line of sight. You can control the 4.
Driving screws Installing the sound bar SHARP designed the sound bar so you may hang them on the wall. Use proper screws (not supplied). See below Align the wall mount slot at the sound bar to the for size and type.
Falling prevention Safety wires (not supplied) are useful to prevent the sound bar from falling off. 2 persons are required to perform this procedure. When mounting on the wall Loop the safety wires (not supplied) into each Align and fix the sound bar to wall mount angle. hole of the wall mount angle as shown.
Do not stand or sit on the sound bar and subwoofer as you may be injured. SOUND BAR HOME THEATER SYSTEM HT-SB603 Sound Bar Do not allow any objects to fall into or to be placed in the bass reflex duct.
Rear view TV remote sensor Double sided tape (Peel off the double sided Infrared emitter tape separator before fixing) SOUND BAR HOME THEATER SYSTEM HT-SB603 remote control HDMI Connection Caution: Turn off all other equipment before making this connection. The illustration below shows the flows of the signals.
For details, refer to the operation manual of the TV. If you are unable to select external speaker setting from the TV menu (E.g. For SHARP LCD TV, it is named as AQUOS AUDIO SP), turn the CEC OFF and ON again.
Audio connections to TVs, DVD players, VCRs, etc. (continued) Connecting a TV, or DVD player, etc. Connect to the TV using an optical digital cable or an audio cable. To audio output terminals HEADPHONE terminal Blu-Ray/ To optical DVD player/Digital digital audio Tuner output...
This is normal. “AQUOS speaker is enabled” message will be displayed if SHARP LCD TV does not detect HT-SB603 during power on. However the message “AQUOS audio with AQUOS LINK is enabled” will be displayed soon as HT-SB603 is detected.
Page 15
General control (continued) Connecting the wireless Subwoofer Menu/ Level/Mode Function The sound bar and subwoofer will link automatically 3D AUDIO 3D AUDIO 1 (wirelessly) when turned on as it is already pre-linked at AV SYNC AV SYNC 0 the factory. If the link cannot be established, please set the connection by the following method.
Page 16
General control (continued) Treble Control 1. Select APC from the remote control menu to adjust 1. Press the BASS/TREBLE button repeatedly to select the time. treble. 2. The sound bar will enter the power standby mode 2. Within 5 seconds, press the VOL (+ or –) button to automatically if no signal is detected after the preset adjust the treble.
Page 17
Rear view of the NFC tag NFC tag provided has unique ID for each sound bar. SHARP will not be held liable for the damages caused by rewriting the tags. Keep all small parts away from children as they may be accidentally swallowed.
Press to skip up. Press to fast forward. Press to skip down. Press to fast reverse. SOUND BAR HOME THEATER SYSTEM HT-SB603 Notes: To disconnect, simply touch your device to the NFC detection area on the subwoofer or NFC tag again.
Make the Bluetooth connection again if the source device is not turned on, or its Bluetooth functionality is off or is Select “HT-SB603 SHARP” from the source device in sleep mode. list. If Passcode* is required, enter “0000”.
● Unplug USB memory device from the USB terminal. Notes: SHARP will not be held liable for the loss of data while the ● USB memory device is connected to the audio system. Files compressed in MP3 and/or WMA format can be played back when connected to the USB terminal.
Wireless Make sure there is no obstacles If something is wrong with this product, check the following connection cannot (especially metal) blocking before calling your authorized SHARP dealer or service center. be established. between the sound bar and subwoofer. General Manually re-link the sound bar and subwoofer (refer page 13).
Troubleshooting chart (continued) Maintenance Condensation Sudden temperature changes, storage or operation in an Cleaning the cabinet extremely humid environment may cause condensation Periodically wipe the cabinet with a soft cloth. inside the cabinet or on the transmitter on the remote Caution: control.
Specifications As part of our policy of continuous improvement, SHARP USB (MP3 / WMA) reserves the right to make design and specification changes for product improvement without prior notice. USB host Complies with USB 1.1 (Full The performance specification figures indicated are interface Speed)/2.0 Mass Storage Class.