Beep Function - Kenwood TS-2000 Instruction Manual

15 OPERATOR CONVENIENCES
1 Press and hold [USB/ LSB/ AUTO]+[
(POWER) to turn the transceiver ON.
2 Press [+] or [–] to select the band to add the
frequency points.
3 Select a memory channel number by turning the
MULTI/ CH control.
4 Turn the Tuning control to select a desired
frequency point to change the operating mode.
Or, press [ENT] to enter the desired frequency
point {page 37} using the numeric keys.
5 Press one of the mode keys to select the desired
operating mode.
• The selected mode appears on the main dot-
matrix display.
6 Repeat steps 4 and 5 until you have added all the
data.
7 Press [CLR] to store the data.
The table below shows the default Auto Mode
frequency points for the HF/ 50 MHz band. When
you activate the Auto Mode selection by pressing
[FUNC], [LSB/ USB/ AUTO], the transceiver
automatically selects the mode; LSB for frequencies
below 9.5 MHz and USB for frequencies greater than
or equal to 9.5 MHz.
C a h n n l e N . o
9
0
9
1
9
2
9
3
•
•
9
2 8
The table below is an example of how to add the
frequency point of 1.62 MHz/ AM into memory. With
this set up, the transceiver selects AM mode below
1.62 MHz, LSB mode from 1.62 MHz to 9.5 MHz and
USB mode from 9.5 MHz to 60.0 MHz.
C a h n n l e N . o
1
0
9
1
9
2
9
3
•
•
9
2 8
74
]
D a a t O e p a r i t g n
5 . M H z
L S B
5 . M H z
0 0 . 3 M
L S B
L S B
5 . M H z
9 5 . M H
L S B
5 . M H z
9 5 . M H
L S B
U S B
•
6 0 0 . M
•
5 . M H z
L S B
D a a t O e p a r i t g n
6 . 2 M H z
0 0 . 3 M
A M
A M
5 . M H z
1 6 . 2 M
L S B
5 . M H z
1 6 . 2 M
L S B
L S B
5 . M H z
9 5 . M H
L S B
•
9 5 . M H
•
U S B
5 . M H z
6 0 0 . M
L S B
The next table is an example of adding 4 frequency
points into memory. With this setup, the transceiver
selects AM mode below 1.62 MHz, CW mode from
1.62 MHz to 2.0 MHz, LSB mode from 2.0 MHz to
9.5 MHz, FM mode from 9.5 MHz to 53.0 MHz and
USB mode from 53.0 MHz to 60.0 MHz. If multiple
data contains the same frequency but a different
mode is entered into memory, the lowest numbered
memory channel is reflected as the Auto Mode.
C a h n n l e
0
1
2
3
•
•
2 8
m o e d
To activate the AUTO MODE function, press [FUNC],
[LSB/ USB/ AUTO].
H z
<

BEEP FUNCTION

z
The Beep function provides you confirmation of entry,
z
error status, and malfunctions of the transceiver.
Although you can turn the beep function OFF by
H z
accessing Menu No. 12, we recommend you leave it
ON in order to detect unexpected errors and
malfunctions.
You can also change the output level of the beeps by
accessing Menu No. 12 and selecting 1 to 9.
The transceiver generates Morse code to tell you
which mode is selected when you change operating
modes.
When you change operating Modes, the following
m o e d
Morse code sounds:
M o
H z
<
L S
H z
U S
H z
C W
<
z C W
F S
z
F S - K
H z
A M / A
F M / F
N . o D a a t
1 6 . 2 M H z
A M
2 0 . M H z
C W
7 0 . M H z
L S B
9 5 . M H z
L S B
•
•
5 3 0 . M H z
F M
e d M r o e s
B · – · ·
B · · –
– · – ·
- R – · – · · – ·
K · – ·
R · – · · – ·
M N · –
M N · · – ·
O e p a r i t g n m o e d
0 0 . 3 M H z
A M <
1 6 . 2 M H z
1 6 . 2 M H z
C W <
2 0 . M H z
2 0 . M H z
L S B <
9 5 . M H z
9 5 . M H z
F M <
5 3 0 . M H z
5 3 0 . M H z
U S B
6 0 0 . M H z
C o e d O u p t t u
( ) L
( U )
( C )
( C R )
( R )
( R R )
( ) A
( ) F