Yamaha MOXF8 Reference Manual page 44

VOICE PERF
RandomPan
Determines the amount by which the sound of the selected Element is panned randomly left and right for each note you
press. The Pan setting (above) is used as the Center Pan position.
Settings:
0 – 127
ScalingPan
Determines the degree to which the notes (specifically, their position or octave range) affect the Pan position, left and
right, of the selected Element. At note C3, the main Pan setting (above) is used for the basic Pan position.
Settings:
-64 – +0 – +63
[SF2] VEL SENS (Velocity Sensitivity)
From this display you can determine how the Amplitude (volume) EG responds to velocity.
EGTime (EG Time Velocity Sensitivity)
Segment (EG Time Velocity Sensitivity Segment)
Determines the velocity sensitivity of the AEG's Time parameters. Select the "Segment," and then set its "EGTime"
parameter.
Settings:
Time: -64 – +0 – +63
Settings:
Segment: atk, atk+dcy, dcy, atk+rls, all
atk (attack)............................... EG Time parameter affects Attack time.
atk+dcy (attack + decay)........ EG Time Value affects Attack/Decay1 time.
dcy (decay) ............................. EG Time parameter affects Decay Time.
atk+rls (attack + release) ........ EG Time Value affects Attack/Release time.
all ............................................. EG Time affects all AEG Time parameters.
Level (Level Velocity Sensitivity)
Offset (Level Velocity Sensitivity Offset)
Curve (Level Velocity Sensitivity Curve)
Determines the velocity sensitivity of the Amplitude EG Level. The "Offset" parameter raises or lowers the level specified
at the "Level." The "Curve" parameter determines how velocity affects the Amplitude EG.
Settings:
Level: -64 – +0 – +63
Settings:
Offset: 0 – 127
Settings:
Curve: 0 – 4
[SF3] AEG (Amplitude EG)
This allows you to make all the time and level settings for the Amplitude EG, which determine how the volume of the
sound changes over time. Using the AEG, you can control the transition in volume from the moment the sound starts is
to the moment the sound stops. The full names of the available parameters are shown in the chart below, as they appear
in the display.
INT (Initial) ATK (Attack)
TIME --- Attack Time
LEVEL Initial Level Attack Level
Initial Level, Attack Time/Level, Decay 1 Time/Level, Decay 2 Time/Level, Release Time
Settings:
TIME: 0 – 127
LEVEL: -128 – +0 – +127
Half Damper Time
Determines how quickly the sound decays to silence after the key is released while holding down the Foot Controller
FC3 with the Half Damper Switch parameter turned on.
Settings:
0 – 127
Half Damper Switch
When the Half Damper Switch is set to on, you can produce a "half-pedal" effect just as on a real acoustic piano by
using the optional FC3 Foot Controller connected to the FOOT SWITCH [SUSTAIN] jack on the rear panel.
Settings:
off, on
NOTE
When you wish to recreate a half-damper effect using the optional FC3, set the "Sustain Pedal" (Foot Switch Sustain Pedal
Select) parameter to "FC3 (Half On)" in the CTL ASN display
necessary when controlling the half-damper by sending Control Change messages from an external MIDI device to the
instrument.
NOTE
For details on AEG, see the "Synthesizer Parameter Manual" PDF document.
MOXF6/MOXF8 Reference Manual
SONG PATTERN MIX
DCY1 (Decay 1)
Decay 1 Time
Decay 1 Level
(page
MASTER REMOTE
DCY2 (Decay 2) REL (Release)
Decay 2 Time Release Time
Decay 2 Level ---
145) of the Utility mode. Note that this setting is not
UTILITY QUICK SET FILE
Voice Mode
Voice Play
[F1] PLAY
[F3] PORTA
[F4] EG
[F5] ARP ED
[F6] EFFECT
Arpeggio Edit
[F2] TYPE
[F3] MAIN
[F4] LIMIT
[F5] PLAY FX
Normal Voice Edit
Common Edit
[F1] GENERAL
[F2] OUTPUT
[F3] EQ
[F4] CTL SET
[F5] LFO
[F6] EFFECT
Element Edit
[F1] OSC
[F2] PITCH
[F3] FILTER
[F4] AMP
[F5] LFO
[F6] EQ
Drum Voice Edit
Common Edit
[F1] GENERAL
[F2] OUTPUT
[F3] EQ
[F4] CTL SET
[F6] EFFECT
SUS (Sustain)
Key Edit
Half Damper Time
[F1] OSC
Half Damper Switch
[F2] PITCH
[F3] FILTER
[F4] AMP
[F6] EQ
Voice Job
[F1] INIT
[F2] RECALL
[F3] COPY
[F4] BULK
Supplementary Information
44