Yamaha MOXF8 Reference Manual page 146

VOICE PERF
AF1 (Assign Function 1 Control Number)
AF2 (Assign Function 2 Control Number)
Determines the Control Change number generated when you use the ASSIGNABLE FUNCTION [1]/[2] buttons. Keep in
mind that if the same MIDI Control Change messages as set here are received from an external device, the internal tone
generator also responds to those messages as if the ASSIGNABLE FUNCTION [1]/[2] buttons of the instrument itself
was used.
Settings:
off, 1 – 95
[SF2] FT SW (Foot Switch)
From this display you can determine the Control Change number generated by using the Footswitch connected to the
FOOT SWITCH jack.
FS (Foot Switch Control Number)
From this display you can determine the Control Change number generated by using the Footswitch connected to the
FOOT SWITCH [ASSIGNABLE] jack. Keep in mind that if the same MIDI Control Change messages as set here are
received from an external device, the internal tone generator also responds to those messages as if the Footswitch of
the instrument itself was used.
Settings: off, 1 – 95, arp sw, play/stop, PC inc, PC dec, octave reset
SustainPedal (Foot Switch Sustain Pedal Select)
Determines which model of an optional Foot Switch connected to the FOOT SWITCH [SUSTAIN] jack is recognized.
When the FC3 is used:
When you connect an optional FC3 (equipped with the half-damper feature) for producing the special "half-
damper" effect (as on a real acoustic piano), set this parameter to "FC3 (Half on)." If you don't need the half-
damper feature or want to disable it while still using an FC3, set this parameter to "FC3 (Half off)."
When the FC4 or FC5 is used:
Select "FC4/5." The FC4 and FC5 are not equipped with the half-damper feature.
Settings:
FC3 (Half on), FC3 (Half off), FC4/5
NOTE
Note that this setting is not necessary when controlling the half-damper feature via Control Change messages from an external
MIDI device to the instrument.
[F5] USB I/O
Mode
Determines the audio input/output connections. The following three settings are available.
Settings:
VST, 2StereoRec, 1StereoRec
VST .................... The audio signal from A/D INPUT [L]/[R] jacks is output to the "USB 1/2" channels of the USB TO [HOST] jack.
Also, the audio signal from the tone generator is output to the "USB 3/4" channels of the USB TO [HOST] jack.
This mode is for using the 2 stereo channels (4 channels) as the output channels. When using the MOXF6/
MOXF8 Editor VST, set this parameter to "VST."
2StereoRec........ The audio signal from A/D INPUT [L]/[R] jacks is output to the "USB 1/2" channels of the USB TO [HOST] jack.
Also, the audio signal from the tone generator is output to the "USB 1/2" channels or the "USB 3/4" channels
of the USB TO [HOST] jack. The output channels for the audio signal from the A/D INPUT [L]/[R] is fixed, but
the output channels for audio signal from the tone generator can be selected for each part. The output
channel for each part is selected in "USB OUTPUT SELECT" of Performance Common Edit
Mixing Common Edit
NOTE
In the Voice mode, the output channel for audio signal from the tone generator is fixed to "USB 3/4."
MOXF6/MOXF8 Reference Manual
SONG PATTERN MIX
(page 116).
MASTER REMOTE UTILITY
(page
QUICK SET FILE
Utility Mode
[F1] GENERAL
[F2] VOICE
[F2] SEQ
[F3] VCE A/D
[F4] CTL ASN
[F5] USB I/O
[F6] MIDI
Utility Job
61) or
146