Adjusting Audio And Video Settings; Using The Setup Screen Menus - Pioneer DV-535 Operating Instructions Manual

Adjusting Audio
and Video
Settings
Using the Setup Screen
Menus
The procedure on this page describes how to operate the
menus on the Setup screen. These menus are used to
set and adjust a number of system settings. The various
functions that can be adjusted are covered throughout
this manual. The procedure on this page provides a basic
outline for using the Setup screen menus.
When setting up for the first time
It is recommended to set up player using the Setup
Navigator (page 16). If you selected [Auto Start Off]
when the Setup Navigator appeared, you may still set up
the player using the Setup Navigator in the General menu
screen.
If you choose not to use the Setup Navigator, be sure to
make the necessary settings in the Setup screen
Audio 1, Audio 2, Video, and Language menus as
described on the following pages.
Some DVDs start playing automatically when loaded in
the player. If a DVD has been loaded, be sure to press
STOP 7 before proceeding.
1
2
3, 4, 5, 6
1
DVD PLAYER
STANDBY/ON
OPEN/
LAST CONDITION CLOSE
MEMORY MEMORY
REPEAT
AUDIO SUB TITLE ANGLE
REPEAT
A-B
SETUP MENU TOP MENU
RETURN
DISPLAY
5 5 ¶
¶
3
2
NEXT
PREV
¢
4
5
∞ ¶
¶
3 8
7
STOP PLAY PAUSE
¶
1 ¡
e E
REV FWD
STEP/SLOW
2 3
1 CLEAR
+10
5 6
4
¶
8 9 0
7
RANDOM PROGRAM SEARCH MODE
Î
0 4 1 ¡ ¢ 7 8 3
Î A
1
Press STANDBY/ON on the front panel
( on the remote control)
2
Press SETUP.
The Setup screen appears.
(Example)
Audio1 Audio2 Video
Dolby Digital Out – Dolby Digital
DTS Out – Off
96kHz PCM Out – 96kHz 3 48kHz
MPEG Out – MPEG 3 PCM
Setup audio
Digital output format/tone adjust
Move
3
Use the cursor buttons (2/3) to select the
menu you want.
As each menu is selected with the cursor, the
settings appear below the menu heading.
4
Press the cursor buttons (∞) to enter the
menu.
The top item within the menu becomes highlighted.
(Example)
Audio1 Audio2 Video
Dolby Digital Out
DTS Out -
96kHz PCM Out – 96kHz 3 48kHz
MPEG Out – MPEG 3 PCM
Change Dolby Digital output mode
Move
5
Use the cursor buttons (5/∞) to select the
setting you want to change.
The options available for each setting appear to the
right when the setting is selected. The current
setting appears with the setting indicator lit.
6
Press the cursor buttons (3) to enter the
setting options.
(Example)
Audio1 Audio2 Video
Dolby Digital Out
DTS Out -
96kHz PCM Out – 96kHz 3 48kHz
MPEG Out – MPEG 3 PCM
Output Dolby Digital
Move
• Not all menu options can be changed while a disc
is playing. In these cases, the options appear
grayed out on the screen and cannot be adjusted.
To change these settings, press STOP 7 first
before pressing SETUP.
• Operating the menu after pressing STOP 7 may
cancel the resume function.
• Some menu options are not immediately
effective if set while a disc is playing. To make
these settings effective, stop playback and then
start again, or change the settings while the disc
is stopped.
Language General
SETUP Exit
Language General
Dolby Digital
Dolby Digital 3 PCM
Exit
SETUP
Language General
Dolby Digital
Dolby Digital 3 PCM
ENTER Select SETUP Exit
continued
23
En