PIONEER Service Manual. A subscription to, or additional copies Also test with plug reversed of, PIONEER Ser vice Manual may be obtained at a (Using AC adapter Earth nominal charge from PIONEER. plug as required)
Page 3
WAVELENGTH : 650 nm FOR CD : MAXIMUM OUTPUT POWER : 5 mW WAVELENGTH : 780 nm LABEL CHECK (for DV-575A-S/WYXCN, WVXCN, DV-575A-K/WYXCN) Additional Laser Caution 1. Laser Interlock Mechanism • Loading switch (S101 on the LOAB Assy) is used for interlock mechanism of the laser.
Page 4
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. DV-575A-S...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING For DV-575A-S/WVXCN For DV-575A-S/WYXCN and DV-575A-K/WYXCN For DV-575A-S/KUXCN/CA, WVXCN and DV-578A-S/KUXCN/CA DV-575A-S/WVXCN only...
Page 9
See Contrast table(2) (English/Italian) Accessory Box See Contrast table(2) Operating Instructions See Contrast table(2) (French/German) (2) CONTRAST TABLE DV-575A-S/KUXCN/CA, WYXCN, WVXCN, DV-575A-K/WYXCN and DV-578A-S/KUXCN/CA are constructed the same except for the following: DV-575A-S/ DV-575A-S/ DV-575A-S/ DV-575A-K/ DV-578A-S/ Mark No. Symbol and Description...
2.2 EXTERIOR SECTION (for DV-575A-S and DV-575A-K) DV-575A-S/WYXCN, WVXCN NON-CONTACT and DV-575A-K/WYXCN only SIDE CONTACT SIDE Refer to "2.6 04 LOADER ASSY". DV-575A-S/KUXCN/CA only DV-575A-S/WYXCN, WVXCN and DV-575A-K/WYXCN only Refer to "2.4 FRONT PANEL SECTION". DV-575A-S...
Page 11
See Contrast table(2) DVD A/V Badge See Contrast table(2) NSP 13 Base Chassis See Contrast table(2) (2) CONTRAST TABLE DV-575A-S/KUXCN/CA, WYXCN, WVXCN and DV-575A-K/WYXCN are constructed the same except for the follow- ing: DV-575A-S/ DV-575A-S/ DV-575A-S/ DV-575A-K/ Mark No. Symbol and Description...
2.4 FRONT PANEL SECTION (for DV-575A-S and DV-575A-K) 8-1/4 8-2/4 8-4/4 8-3/4 NON-CONTACT SIDE CONTACT SIDE DV-575A-S...
Page 15
Rubber Foot VEB1349 FL Lens VNK5414 Screw PPZ30P080FNI Pioneer Name Plate See Contrast table(2) (2) CONTRAST TABLE DV-575A-S/KUXCN/CA, WYXCN, WVXCN and DV-575A-K/WYXCN are constructed the same except for the follow- ing: DV-575A-S/ DV-575A-S/ DV-575A-S/ DV-575A-K/ Mark No. Symbol and Description KUXCN/CA...
Page 19
Rear View Daifree Daifree No. 23 No. 23 GEM1036 GEM1036 Tray Tray Concave of unevenness Concave of unevenness Inner side of a ditch Daifree GEM1036 Top View Bottom View Side of the rib Concave of unevenness Daifree Daifree GEM1036 GEM1036 DV-575A-S...
CN601 CN103 CN602 LOAD- LOAD- LOAD+ LOAD+ – S101 TRIN IC203 IC202 LOADING K4S641632H-TC75-K V+3D V+3D MOTOR FLASH ROM 64M SDRAM ASSY TROUT ı1/3 ı1/3 LOAB ASSY POWER SUPPLY UNIT CN201 (15P) CN301 (13P) (13P) LIVE AC IN NEUTRAL DV-575A-S...
Page 21
AV CONNECTOR V OUT V IN G/Py (RGB)-TV/AV IC471 MM1505XN RECEIVER Y OUT Y IN R/C/Pr IC451 MM1566AJ VIDEO DRIVE AMP IC472 MM1507XN DV-575A-S/WYXCN, WVXCN, CN941 DV-575A-K/WYXCN ONLY S VIDEO CN452 CN911 DV-575A-S/KUXCN/CA, (5P) (5P) DV-578A-S/KUXCN/CA ONLY JCKB ASSY Remote Sensor...
Page 23
L OUT V+5V ı2/3 R OUT V+5V AV CONNECTOR 1,5, 14,16 (RGB)-TV/AV IC471 MM1505XN RECEIVER IC451 MM1566AJ VIDEO DRIVE AMP IC472 MM1507XN DV-575A-S/WYXCN, WVXCN, CN941 DV-575A-K/WYXCN ONLY S VIDEO CN452 CN911 DV-575A-S/KUXCN/CA, (5P) (5P) DV-578A-S/KUXCN/CA ONLY JCKB ASSY V+3E CN101 (15P)
3.4 DVDM ASSY (1/3) DVDM ASSY (DV-575A-S/KUXCN/CA, DV-578A-S/KUXCN/CA : VWS1582) (DV-575A-S/WYXCN, WVXCN, DV-575A-K/WYXCN : VWS1583) (RF) (RF) (RF) (RF) LD Driver for CD (RF) (RF) (RF) (RF) (RF) (RF) (RF) LD Driver for DVD (RF) Focus, Tracking, Stepping, Spindle and Loading Driver...
Page 29
: VIDEO SIGNAL ROUTE (G/Y) (B/CB) : VIDEO SIGNAL ROUTE (B/CB) (SY) : S VIDEO SIGNAL ROUTE (Y) (SC) : S VIDEO SIGNAL ROUTE (C) : VIDEO SIGNAL ROUTE (V) : AUDIO SIGNAL ROUTE (DIGITAL ch) CN101 (AD) : AUDIO DATA SIGNAL ROUTE DV-575A-S...
3.5 DVDM ASSY (2/3) DVDM ASSY (DV-575A-S/KUXCN/CA, DV-578A-S/KUXCN/CA : VWS1582) (DV-575A-S/WYXCN, WVXCN, DV-575A-K/WYXCN : VWS1583) 5V Regulator DVD IC BA00BC0WT 1.8V Regulator DVD IC 3V Regulator (B/CB) (G/Y) (R/CR) (SC) (SY) (G/Y) (B/CB) (R/CR) DV-575A-S/WYXCN, WVXCN, DV-575A-K/WYXCN ONLY DV-575A-S...
Page 31
: VIDEO SIGNAL ROUTE (G/Y) (B/CB) : VIDEO SIGNAL ROUTE (B/CB) (SY) : S VIDEO SIGNAL ROUTE (Y) (SC) : S VIDEO SIGNAL ROUTE (C) : VIDEO SIGNAL ROUTE (V) DV-575A-S/WYXCN, WVXCN, DV-575A-K/WYXCN ONLY Video Driver Amp. (FL) (B/CB) (B/CB) (G/Y) (G/Y) (SC)
3.6 DVDM ASSY (3/3) DVDM ASSY (DV-575A-S/KUXCN/CA, DV-578A-S/KUXCN/CA : VWS1582) (DV-575A-S/WYXCN, WVXCN, DV-575A-K/WYXCN : VWS1583) (SW) COAXIAL DIGITAL (AD) AUDIO OUT OPTICAL (SL) (AD) (FL) 11 14 (AD) : AUDIO DATA SIGNAL ROUTE (AD) : AUDIO SIGNAL ROUTE (DIGITAL ch)
Page 33
SW for Mute Control CENTER (SW) WOOFER (SW) (SW) Mute SW SW for Mute Control (SL) (SL) (SL) SURROUND Mute SW SW for Mute Control DV-575A-S/WYXCN, WVXCN, DV-575A-K/WYXCN ONLY (FL) (FL) Mute FRONT (FL) (FL) Mute (FL) Mute L AUDIO Mute (2 ch) Reference Voltage Gen.
Page 35
: VIDEO SIGNAL ROUTE (G/Y) (B/CB) : VIDEO SIGNAL ROUTE (B/CB) (SY) : S VIDEO SIGNAL ROUTE (Y) (SC) : S VIDEO SIGNAL ROUTE (C) : VIDEO SIGNAL ROUTE (V) DV-575A-S/WYXCN, WVXCN, DV-575A-K/WYXCN ONLY (FL) (FL) (B/CB) (B/CB) AV CONNECTOR (RGB) (G/Y)
4.3 FLKY and PWSB ASSYS (for DV-575A-S and DV-575A-K) SIDE A PWSB ASSY (VNP1956-B) CN102 IC104 D102 S103 FL DIM V101 SIDE B CMKD-P3X R138 PWSB ASSY CN103 (VNP1956-B) DV-575A-S...
Page 47
VWG2487- VWG2484- VWG2488- S119 V+3E VWG2485- PLAY VWG2486- IC104 V+3E V+3E VNP1956-B S105 S106 S107 S108 S117 EJECT << >> STOP PAUSE DC FC CONTACT SIDE C181 C101 L101 CN101 CN104 CN101 CN201 SIDE B CN101 FLKY ASSY (VNP1956-B) DV-575A-S...
4.4 FLKY and PWSB ASSYS (for DV-578A-S) SIDE A FLKY ASSY (VNP1907-A) CN102 D102 D101 PYKC F4X S102 FL DIM D104 S104 >> S103 FL101 << PWSB ASSY (VNP1907-A) SIDE B PWSB ASSY (VNP1907-A) C154 R138 PWSB CN103 FLKY ASSY (VNP1907-A) DV-575A-S...
Page 49
LEFT ENTER S112 TOP MENU S108 EJECT IR101 /STOP /PLAY S110 S117 S118 S119 DC FC PLAY/>> PAUSE/<< DOWN RETURN S107 S106 C101 HOME MENU/PAUSE STOP/EJECT CN101 CN104 S105 CN101 CN201 SIDE B CN101 C N 1 0 1 DV-575A-S...
[Electrical Part] screw screw Electrical adjustments are not required. 6.2 JIGS AND MEASURING INSTRUMENTS Test mode remote control Screwdriver (large) Screwdriver (medium) TV monitor unit (GGF1381) Screw tight (GYL1001) DVD test disc Precise screwdriver Soldering iron (GGV1025) DV-575A-S...
Mechanical ~, Ÿ Exchange the 03 SD Pickup Assy-S point with the Screw tight. Electric point Mechanical Exchange the Traverse Mecha. point Assy-S Electric point Exchange PCB Assy Mechanical Exchange PC Board point LOAB and DVDM ASSYS Electric point DV-575A-S...
• After going into test mode, if you play back the disc, "DISC-NON" is displayed. • The video signal and the audio signal are outputted during the test mode. • The SKIP key and the SCAN key are effective during the test mode. TEST MODE: OFF POWER GGF1381 Test mode remote control unit DV-575A-S...
(Refer to "6.1 ADJUSTMENT ITEMS AND LOCATION".) Joint 7.5mm Mechanism base • Attach the Traverse Mecha. Assy-S to the 04 LOADER Assy. • Turn it over and attach the joint and the joint spring. • Arrange the flexible cables. (Refer to "7.1.10 DISASSEMBLY".) DV-575A-S...
Page 63
90 degrees step till BER becomes CHP/TIM over "1E-3" again . • Record the number of rotation (N1). • Fasten the tangential adjustment screw till the number of rotation becomes Service mode end harf of N1. DV-575A-S...
3 LD ON DVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650n). : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n). DV-575A-S...
: [NTSC] PAL system : [PAL] Automatic setting : [AUTO] Scart terminal output [SK – ∗ ∗] (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] DV-575A-S...
• Region confirmation mode (ESC + AUDIO [Test mode remote control unit] + "1"-"8" [Test mode remote control unit] keys) After you press the AUDIO key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. DV-575A-S...
Display it according to model information set from the FL controller. 2 Region No. 3 Part number 4 ROM version 5 Flash size 6 FL controller version 7 CHIP VERSION 9 Remote control code 0 Key code of Main unit DV-575A-S...
%%e -2 : NG 7.0e -4 : NG 3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors) Note: ∗ Error of AV1 is not supported in this player. Indication plan contents Character in bold : Item name : Information display DV-575A-S...
Measure the voltage between the two ends of R21 or R26 on the DVDM Assy. If the voltage is 0.4 V or higher, the 780-nm LD is degraded. 03 SD PICKUP ASSY-S DVDM ASSY CN101 Front side SIDE A DV-575A-S...
DVDM Assy displayed on the monitor Check the video signal path between DVD IC (DVDM Assy IC201) and Video circuit after DVD IC (The FL display lights. The video-out terminal (see the block diagram) (IC201) mechanism does not work.) DV-575A-S...
Page 71
Is signal output from audio DAC IC on the DVDM Assy ? DVDM Assy (Picture is normal) Main CH : IC501-pin 7, pin 8 Audio Dac IC (IC501) Multi CH : IC601-pin 7, pin 8, IC701-pin 7, pin 8 Audio Dac IC (IC601, IC701) DV-575A-S...
Page 72
Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be (DVDM Assy : IC201) generated, because the DVD processing is performed by a single chip. 64M SDRAM No power. (DVDM Assy : IC202) Block noise is generated during playback. DV-575A-S...
ID number. 0 0 0 0 0 0 0 0 1 Note: If you press the PLAY button before inputting a 9-digit ID <PLAY> Enter number, the unit returns to Step 2 without doing anything else. Input ID Number ! DV-575A-S...
Page 74
(The STOP key is not accepted after all 9 digits have been entered.) [Player's ID Number Setting] ID Number ? 0 0 0 0 0 0 0 0 1 Compare 0 0 0 0 0 0 0 0 1 <PLAY> Enter <STOP> Memory Clear Input ID Number ! DV-575A-S...
Page 75
Insert The ID Data Disc ! If no ID data are set after the ID number is changed, the message "NO ID DATA" flashes on the screen and FL display for a few seconds after the power is turned on or during Stop mode. DV-575A-S...
The picture appears [FL controller] Request communication to DVD IC (FP_XRDY) [DVD IC] Outputs the communicable signal to FL controller (FP_ACK) DVD IC – FL controller communication [DVD IC] Accesses 64M SDRAM (part) The opening picture appears (Pioneer Logo) DV-575A-S...
Assy in the direction of the arrow, as indicated in the photo. If the tray pops out a little, fully pull it out by a hand. Screwdriver (small) Projection Slit Drive cam Tray open 04 LOADER Assy Screwdriver (small) DV-575A-S...
Page 78
Front panel section Remove the six hooks. Remove the front panel section. DVDM Assy Remove the four screws. Remove the three screws. ×3 DVDM Assy DVDM Assy Remove the DVDM Assy and stand it against the other parts. Diagnosis DV-575A-S...
Page 79
Short-circuit two points of C and D by soldering. Rear view Note: After replacement, connect the flexible cable, then remove the soldered joint (open). Disconnect the four connectors. Remove the four screws. Remove the 04 LOADER Assy. 04 LOADER Assy DV-575A-S...
Page 80
Hook Bridge Tray Drive cam Note when reinserting the Tray When reinserting the tray, first align the triangle printed on the loading base and the pin of the drive cam, then insert the tray. Front Side Loading base Triangle DV-575A-S...
Page 81
Flexible cable Dislodge the flexible cables from their packaged for the spindle motor Front Side placement. Flexible cable for the pickup Bottom View Traverse Mecha. Assy-S × 2 Remove the four hooks. Remove the Traverse Mecha. Assy-S. × 2 DV-575A-S...
Page 82
Bottom View Adjustment Adjustment screw screw (Skew screw) (Skew screw) Remove the two adjustment screws. 03 SD Pickup Assy-S Remove the 03 SD Pickup Assy-S. Note: Be careful not to lose the spring for the skew screw. Skew screw Spring DV-575A-S...
Page 83
Note: The screw is secured with the silicone adhesive. Make sure to apply the silicone adhesive after reattaching the screw. Silicone Adhesive GEM1037 Arrangement of the flexible cable for the spindle motor : Conductive surface Hook Hook Bottom View DV-575A-S...
Page 84
Attach the flexible cable of the pickup to the connector. Fold the flexible cable along the hook. Pass the flexible cable through the hook. Hook Backing Bottom View Front Side Hook Pass the flexible cable through the hook. Hook Hook Make sure that the cable is loose DV-575A-S...
Page 86
Drive Deinterlacer Processor Spindle Control MPEG-1/2 Flash ROM MPEG-4 Audio JPEG Memory Video Decoder Controller Video CCIR601/65 SACD Input DRAM Processor PCM / DSD Audio System Controller Parser Audio Output CPPM/CPRM SPDIF System GPIO Audio 30-bit Input RISC IR/VFD DV-575A-S...
Page 87
Analog Inout SACD- TOP Reference 243 S_VREFN Analog Inout SACD- Bottom Reference Reference Voltage (3) Name Alt. Function 28 V2REFO Analog output Reference voltage 2.8V 29 V20 Analog output Reference voltage 2.0V 30 VREFO Analog output Reference voltage 1.4V DV-575A-S...
Page 88
42 FOO Analog Output Focus servo output. PDM output of focus servo compensator LVTTL 3.3V Input, Schmitt Input, 47 FG (Digital pin) V_ADIN8 pull-up , with Motor Hall sensor input, or Version AD input 8 analog input path for V_ADIN8 DV-575A-S...
Page 89
Flash address 19 / IO 76 IOA20 Inout, 2-16MA, SR, SMT Flash address 20 / IO Flash address 21 / IO Inout, 2-16MA, While External FLASH size <= 2MB: 89 IOA21 V_ADIN0 SR, SMT Version AD input port 0, or GPIO DV-575A-S...
Page 90
C clock pin Microcontroller port 3-5 107 UP3_5 Inout, 4MA, SR, PU, SMT Hardwired RD232 TXD C data pin 111 IR Input, SMT IR control signal input Inout, 2-16MA, 112 INT0# Microcontroller external interrupt 0, active low SR, PU, SMT DV-575A-S...
Page 91
0 : normal operation While only 2 channels output: Microcontroller external interrupt 1 GPIO Microphone serial input While not support Microphone: 224 MC_DATA INT2# Inout Microcontroller external interrupt 2 GPIO Output, 2-16MA, 225 SPDIF SPDIF output SR : ON/OFF DV-575A-S...
Page 92
46 USB_VDD3 USB Power USB Power pin 3.3V 110 PRST# Input PU, SMT Power on reset input, active low 109 ICE Input PD, SMT Microcontroller ICE mode enable 228 XTALO Output 27M crystal out 229 XTALI Input 27M crystal in DV-575A-S...
Page 93
Digital Video output Y bit 0 GPIO DRAM data 25 While using 16-bits wide DRAM: SDO1 Inout Serial interface port 1 data-out 176 RD25 MS_SDIO Non-pull MS Card SDIO pin part II SMPTE_Y[1] Digital Video output Y bit 1 GPIO DV-575A-S...
Page 94
DRAM address 3 150 RA2 Inout DRAM address 2 149 RA1 Inout DRAM address 1 147 RA0 Inout DRAM address 0 146 RA10 Inout DRAM address 10 145 BA1 Inout DRAM bank address 1 143 BA0 Inout DRAM bank address 0 DV-575A-S...
Page 95
Version AD input port 6 SDCLK Security Disk Clock part I GPIO JTAG data out While not using Boundary Scan: SDCS3 Serial interface port 3 chip-select 51 TDO V_ADIN7 Inout Version AD input port 7 MSCLK Memory Stick Clock part I GPIO DV-575A-S...
7.4 CLEANING Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Cleaning tools Pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DV-575A-S...
• GGV1175 is to be released in May, 2004. Use only GGV1175 after GGV1175 was released because GGV1175 includes all the data of GGV1171. DVD Test Disc (DVD-Video) GGV1025 Check of DVD-Video CD Test Disc STD-905 Check of CD DVD Test Disc (DVD-Audio) GGV1070 Check of DVD-Audio DV-575A-S...