Using The Control - Samsung RF24FSEDBSR/AA User Manual

French
USING THE CONTROL PANEL
RF24FS**
iiiiiiii_ii_iiiiiiiiiiiii_i_!_i_!_i!i!_i!i!_!_ii!_i!i!i{_i_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_!
Tbuching this button turns Energy Saver
mode on and off. When you turn Energy
Saver on, the Energy Saver icon lights.
Turn Energy Saver off and the icon goes
off. The Energy Saver function's factory
setting is "ON". If condensation or water
drops appear on the doors, turn the
Energy Saver mode off.
®
The Freezer button serves two purposes:
To set the Freezer to your desired
temperature.
To turn the power freezer function on
and off.
) To set the Freezer temperature
Touch the Freezer button to set the
Freezer to your desired temperaiure. You
carl set the temperature between 5 °F
(-15 °C) and -8 °F (-23 °C).
2) Power Freezer function
Touch and hold this butters for 3 seconds
to decrease the time needed to freeze
products in the Freezer.
It carl be helpful if you need to quickly
freeze easily spoiled items or if the
temperature in the freezer has warmed
dramaiically (For example, if the door was
left open).
When you use this function the energy
consumption of the refrigerator will
increase. Remember to turn it off when
you don't need it and return the freezer
to your original temperature setting. If you
need to freeze large amount of food stuff,
activate Power Freeze function at least 24
hours before.
16 operat -_g
i!_!ii_i{,i_iiiiiiiii_i!i!i!ii{!iii!i{_iiii_t_i{{_i!{i!iiiiiiiiii{ii!!!!iiiii
,q.
The Alarm button serves two purposes:
To turn the door open alarm on and off
To reset the water filter life indicator.
Door Alarm Function
If the door alarm is set to On, an alarm
beeps if any refrigerator door is left open
for more than three minutes. The beeping
stops when you close the door. The door
alarm function is pre--set to On in the
factory. You carl turn it off by pressing and
then releasing the Alarm button. You carl
turn it back on in the same fashion. The
icon lights up when the function is ors.
When the Door Alarm function is on and
the alarm sound is triggered, the Door
Alarm Icon will blink while the alarm
sounds.
2) Water Filter Lif_ Indicator Function
After you replace the water filter, touch
and hold this button for 3 seconds to
reset the water filter life indicator. When
you reset the water filter life indicator, the
Filter icors ors the panel turns OFF.The
Filter icors will turn red to let you know it
is time to change the water filter after six
months (about 300 gallons). Seme areas
have large amounts of lime in their water,
which causes the water filter to clog more
quickly. If this is the case in your area,
you will have to change the filter more
frequently than every six months.
Lighting button serves two purposes:
To turn the dispenser light on and off
To switch the temperature units
between °C and °F
) Light Function
Tbucl'sing the Lighting button turns ors
the Dispenser LED lamp in continuous
mode so that it stays on continuously.
The butters also lights up. If you want the
Dispenser lamp to come ors only when
some one uses the dispenser, press the
Lighting button to turn the continuous
mode off.
2) To switch the temperature units
between °C and °F
touch and hold this button for 3 seconds
to select the temperature display you
want.
Each time you press and hold the button,
the °C and °F temperature modes
alternate and the °C or °F icors lights up,
indicating your selection.