Sign in today to find solutions:

Don't have an account? Sign up

 
eMachines E627
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to
http://csd.acer.com.tw
PRINTED IN TAIWAN
Next page ->

Summary of Contents

  • Page 1

    E627 Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.tw PRINTED IN TAIWAN...

  • Page 2

    Revision History Please refer to the table below for the updates made on eMachines E627 service guides. Date Chapter Updates...

  • Page 3: Table Of Contents

    Copyright Copyright © 2009 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.

  • Page 4

    Conventions The following conventions are used in this manual: Denotes actual messages that appear SCREEN MESSAGES on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions.

  • Page 5

    Preface Before using this information and the product it supports, please read the following general information. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.

  • Page 7: Table Of Contents

    E627 BIOS ........

  • Page 8: Table Of Contents

    Table of Contents Removing the Power Board ........65 Removing the Left Speaker Module .

  • Page 9: Table Of Contents

    E627 Exploded Diagrams ........146...

  • Page 10

    Table of Contents...

  • Page 11: Features

    Chapter 1 System Specifications Features Below is a brief summary of the computer’s many features: Operating System • Genuine Windows® Vista™ Platform • AMD Athlon™ 64 X2 dual-core processor • AMD Athlon™ 64 single-core processor • AMD M780G Chipset System Memory •...

  • Page 12

    • Headphone/Line out jack Dimensions and Weight • 372.3mm x 246.5mm x 26.8mm/40.6mm with ID • Weight < than 3100g (15.6" LCD/6-cell battery/super-multi ODD) Communication • Wireless • 802.11b/g/n WLAN/WiMax • Mini PCIE Wireless LAN module with with mini card slot •...

  • Page 13

    • Kensington Lock (7.5mm) Environment • Temperature: • Operating: 5 °C to 35 °C • Non-operating: -20 °C to 65 °C • Humidity (non-condensing): • Operating: 20% to 80% • Non-operating: 20% to 80% Chapter 1...

  • Page 14: System Block Diagram

    System Block Diagram Chapter 1...

  • Page 15: Your Acer Notebook Tour, Front View

    Your Acer Notebook tour After knowing your computer features, let us show you around your new computer. Front View Icon Item Description Integrated Web camera for video communication webcam (for selected models). Display screen Also called Liquid-Crystal Display (LCD), displays computer output. Touchpad toggle Turns the internal touchpad on and off.

  • Page 16: Closed Front View

    Icon Item Description Click buttons (left The left and right buttons function like the left and right) and right mouse buttons. Palmrest Comfortable support area for your hands when you use the computer. Indicates when the hard disk drive is active. Num Lock Lights up when Num Lock is activated.

  • Page 17: Rear View, Left View

    Rear View Icon Item Description Ventilation slots Enable the computer to stay cool, even after prolonged use. Left View Icon Item Description DC-in jack Connects to an AC adapter Ethernet (RJ-45) Connects to an Ethernet 10/100-based port network. External display Connects to a display device (VGA) port (e.g.

  • Page 18: Right View, Bottom View

    Right View 2 3 4 Item Description Optical drive Internal optical drive; accepts CDs or DVDs. Optical disk access Lights up when the optical drive is active. indicator Optical drive eject button Ejects the optical disk from the drive. Emergency eject hole Ejects the optical drive tray when the computer is turned off.

  • Page 19

    Icon Item Description Battery lock Locks the battery in position. Hard disk bay Houses the computer's hard disk (secured with screws). Memory Houses the computer's main memory. compartment Ventilation slots Enable the computer to stay cool, even after and cooling fan prolonged use.

  • Page 20: Indicators

    Indicators The computer has several easy-to-read status indicators. The front panel indicators are visible even when the computer cover is closed. Icon Function Description Power Indicates the computer's power status. Battery Indicates the computer's battery status. Indicates when the hard disk drive is active. Num Lock Lights up when Num Lock is activated.

  • Page 21: Touchpad Basics

    TouchPad Basics The following items show you how to use the TouchPad: • Move your finger across the TouchPad (1) to move the cursor. • Press the left (2) and right (3) buttons located beneath the TouchPad to perform selection and execution functions.

  • Page 22: Using The Keyboard, Lock Keys And Embedded Numeric Keypad

    Using the Keyboard The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function and special keys. Lock Keys and embedded numeric keypad The keyboard has three lock keys which you can toggle on and off. Lock key Description Caps Lock...

  • Page 23: Windows Keys

    Windows Keys The keyboard has two keys that perform Windows-specific functions. Description Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu. It can also be used with other keys to provide a variety of functions: <...

  • Page 24: Hot Keys

    Hot Keys The computer employs hotkeys or key combinations to access most of the computer’s controls like screen brightness, volume output and the BIOS utility. To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination. Hotkey Icon Function...

  • Page 25: Special Key

    Special Key You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your keyboard. The Euro symbol Open a text editor or word processor. Hold <Alt Gr> and then press the <5> key at the upper-center of the keyboard. NOTE: Note: Some fonts and software do not support the Euro symbol.

  • Page 26: Using The System Utilities, Acer Gridvista (dual-display Compatible)

    Using the System Utilities Acer GridVista (dual-display compatible) NOTE: This feature is only available on certain models. To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the display box and then click the check box Extend my windows desktop onto this monitor.

  • Page 27: Hardware Specifications And Configurations

    Hardware Specifications and Configurations Processor Item Specification • AMD Athlon64 Dual-Core Process, Cache 1MB, TK42 • AMD Athlon64 Process, 2.2GHz, Cache 256KB, TF38 • AMD Athlon64 Process, 2.0GHz, Cache 256KB, TF36 • AMD Athlon64 Process, 1.6GHz, Cache 512KB, TF20 Type AMD Athlon64 Dual-Core Mobile CPU Core Logic •...

  • Page 28

    Item Specification BIOS ROM type Flash Features • Flash ROM 1MB • Supports ISIPP • Supports Acer UI • Supports multi-boot • Suspend to RAM (S3)/Disk (S4) • Various hot-keys for system control • Supports SMBUS 2.0, PCI2.3 • ACPI 2.0 compliance with Intel Speed Step support C1, C2, C3, C4 and S3, S4 for mobile CPU •...

  • Page 29

    capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be reversed. LAN Interface Item Specification LAN Chipset Atheros AR8132L Package LAN connector type LAN connector location Feature Interface Wireless Module 802.11b/g/n Item Specification Manufacturer Foxconn...

  • Page 30

    Item Specification Performance Specifications Buffer size 8 MB 8 MB 8 MB 8 MB Interface SATA SATA SATA SATA Internal transfer 395~952 850 Mbits/s rate (Mbits/sec, (typical) maximum max) I/O data transfer 300 maximum rate (Mbytes/sec max) DC Power Requirements Voltage 5V ±5% 5V ±5%...

  • Page 31

    Item Specification Applicable disc formats DVD-ROM: DVD Read: • DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), 4.7GB (Single Layer) • DVD-Video, DVD-Audio, SACD (Hybrid), 8.5GB (Dual Layer) • UDF DVD, DVD-R, DVD-R DL, DVD-R 3.95 GB, DVD-R: • DVD-R Authoring, DVD-R Multi-Border, 3.95GB (Ver.

  • Page 32

    Item Specification Dimensions Weight Nominal Impedance 4Ohm Power Rating Output Sound Pressure Level Frequency Range Distortion Microphone Item Specification Vendor and Model Directivity Current Consumption S/N Ratio Frequency Power and Keyboard Controller Item Specification Controller EM-7T Package Features • Touchpad pointing device Supply Current Total number of keypads 99-/100-/103-key keyboard...

  • Page 33

    Item Specification Contrast Ratio 500:1 Response Time (Optical Rise Time/Fall Time) msec Input Voltage Typical Power Consumption 5.75 (watt) Weight (with inverter) Physical Size (mm) 359.3 x 209.5 x 5.9 Electrical Interface LVDS Support Color 262K Viewing Angle (up/down/right/ 20/45/45/45° left) Temperature Range (°C) Operating...

  • Page 34

    Chapter 1...

  • Page 35: Bios Setup Utility, Navigating The Bios Utility

    Chapter 2 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup.

  • Page 36: Emachines E627 Bios, Information

    E627 BIOS Information The Information screen displays a summary of your computer hardware information. P h o e n i x B I O S S e t u p U t i l i t y Information M a i n...

  • Page 37: Main

    Main The Main screen allows the user to set the system time and date as well as enable and disable boot option and recovery. P h o e n i x B I O S S e t u p U t i l i t y Information M a i n Security...

  • Page 38: Security

    Security The Security screen contains parameters that help safeguard and protect your computer from unauthorized use. P h o e n i x B I O S S e t u p U t i l i t y Information M a i n Security B o o t...

  • Page 39

    Setting a Password Follow these steps as you set the user or the supervisor password: Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Supervisor Password box appears: S e t S u p e r v i s o r P a s s w o r d E n t e r N e w P a s s w o r d C o n f i r m N e w P a s s w o r d Type a password in the “Enter New Password”...

  • Page 40

    Changing a Password Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears. S e t S u p e r v i s o r P a s s w o r d E n t e r C u r r e n t P a s s w o r d E n t e r N e w P a s s w o r d C o n f i r m N e w P a s s w o r d...

  • Page 41: Boot

    Boot This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay. Select Boot Devices to select specific devices to support boot. P h o e n i x B I O S S e t u p U t i l i t y Information M a i n...

  • Page 42: Exit

    Exit The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility. P h o e n i x B I O S S e t u p U t i l i t y Information M a i n Security...

  • Page 43: Bios Flash Utilities

    BIOS Flash Utilities The BIOS flash memory update is required for the following conditions: • New versions of system programs • New features or options • Restore a BIOS when it becomes corrupted. Use the Phlash utility to update the system BIOS flash ROM. NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette before you use the Phlash utility.

  • Page 44: Dos Flash Utility

    DOS Flash Utility Perform the following steps to use the DOS Flash Utility: Press F2 during boot to enter the Setup Menu. Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move USB HDD to position 1.

  • Page 45: Winflash Utility

    In flash BIOS, the message Please do not remove AC Power Source displays. Plug in the AC power to continue. Flash is complete when the message Flash programming complete displays. WinFlash Utility Perform the following steps to use the WinFlash Utility: Double-click the WinFlash executable.

  • Page 46: Remove Hdd/bios Password Utilities

    Remove HDD/BIOS Password Utilities This section provides you with details about removing HDD/BIOS password: Remove HDD Password: If you key in the wrong HDD password three times, an error is generated. To reset the HDD password, perform the following steps: An error code is generated for unlocking the HDD.

  • Page 47

    Removing BIOS Passwords: To clear the User or Supervisor passwords through hardware, open the WLAN door and use a metal instrument to short the J1 jumper. Cleaning BIOS Passwords To clean the User or Supervisor passwords using software utilites, perform the following steps: From a DOS prompt, execute clnpwd.exe Press 1 or 2 to clean the desired password shown on the screen.

  • Page 48

    The onscreen message determines whether the function is successful or not. Using Boot Sequence Selector The Boot Sequence Selector allows the boot order to be changed without accessing the BIOS. To use Boot Sequence Selector, perform the following steps: Enter into DOS. Execute BS.exe to display the usage screen.

  • Page 49

    Using DMITools The DMI (Desktop Management Interface) Tool copies BIOS information to EEPROM to be used in the DMI pool for hardware management. When the BIOS displays Verifying DMI pool data it is checking that the table correlates with the hardware before sending to the operating system (Windows, etc.).

  • Page 50

    Using the LAN MAC EEPROM Utility You can use the MAC.BAT utility to write the MAC.CFG file to the EEPROM under DOS mode. Use a text editor (for example: Notepad) to open the MAC.CFG file. You can see the MAC.CFG contents as below: WriteData = ‘001122334455' MAC value...

  • Page 51: Disassembly Requirements

    Chapter 3 Machine Disassembly and Replacement IMPORTANT: The outside housing and color may vary from the mass produced model. This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting. Disassembly Requirements To disassemble the computer, you need the following tools: Wrist grounding strap and conductive mat for preventing electrostatic discharge •...

  • Page 52: Pre-disassembly Instructions, Disassembly Process

    Pre-disassembly Instructions Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system. 3.

  • Page 53: External Module Disassembly Process, External Modules Disassembly Flowchart

    External Module Disassembly Process IMPORTANT: The outside housing and color may vary from the mass produced model. External Modules Disassembly Flowchart The flowchart below gives you a graphic representation of the external module disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the keyboard, you must first remove the switch board.

  • Page 54: Removing The Battery Pack

    Removing the Battery Pack 1. Turn computer over. Slide the battery lock in the direction shown. 2. Slide and hold the battery release latch to the release position (1), then lift out the battery pack from the main unit (2). Chapter 3...

  • Page 55: Removing The Sd Dummy Card

    Removing the SD Dummy Card 1. Push the SD dummy card all the way in to eject it. 2. Pull it out from the slot. Chapter 3...

  • Page 56: Removing The Lower Covers

    Removing the Lower Covers 1. See “Removing the Battery Pack” on page 44. 2. Remove the three screws securing the Memory and HDD Covers. Memory Cover Cover Step Size Quantity Screw Type Lower Covers M2.5*8 3. Remove the HDD cover as shown. 4.

  • Page 57: Removing The Optical Drive Module

    Removing the Optical Drive Module 1. See “Removing the Battery Pack” on page 44. 2. Remove the screw securing the ODD module. Step Size Quantity Screw Type ODD Module M2.5*8 3. Insert a suitable tool into the access slot in the battery bay as shown. Gently lever the ODD module out of the chassis.

  • Page 58

    5. Remove the two screws securing the ODD bracket and remove the ODD bracket from the optical disk drive module. Step Size Quantity Screw Type ODD Bracket M2*3 6. Remove the ODD bezel by rotating the top edge downward and pulling it clear of the module. Chapter 3...

  • Page 59: Removing The Dimm Modules

    Removing the DIMM Modules 1. See “Removing the Lower Covers” on page 46. 2. Push out the release latches on both sides of the DIMM socket to release the DIMM module. 3. Remove the DIMM module. 4. Repeat steps for the second DIMM module if present. Chapter 3...

  • Page 60: Removing The Wlan Module

    Removing the WLAN Module 1. See “Removing the Lower Covers” on page 46. 2. Remove the adhesive tape securing the Antenna cables in place. 3. Disconnect the antenna cables from the WLAN Board. NOTE: Cable placement is Black to the MAIN terminal (upper) and White to the AUX terminal (lower). Chapter 3...

  • Page 61

    4. Move the antenna away and remove the two screws to release the WLAN Board. Step Size Quantity Screw Type WLAN Module M2*3 5. Detach the WLAN Board from the WLAN socket. NOTE: When reattaching the antennas, ensure the cables are tucked into the chassis to prevent damage. Chapter 3...

  • Page 62: Removing The Hard Disk Drive Module

    Removing the Hard Disk Drive Module 1. See “Removing the Lower Covers” on page 46. 2. Using the pull-tab, slide the HDD Module in the direction of the arrow to disconnect the interface. 3. Lift the HDD Module clear of the HDD bay. NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.

  • Page 63

    4. Remove the four screws (two each side) securing the hard disk to the carrier. Step Size Quantity Screw Type HDD Carrier M3*3 5. Remove the HDD from the carrier. Chapter 3...

  • Page 64: Main Unit Disassembly Process, Main Unit Disassembly Flowchart

    Main Unit Disassembly Process Main Unit Disassembly Flowchart Remove External Remove Remove Modules before Switch Cover Keyboard proceeding Remove LCD Module Remove Upper Cover Upper Lower Cover Cover Remove Remove Remove Remove Left Speaker Right Speaker TouchPad Power Board Module Module Bracket Remove...

  • Page 65: Removing The Switch Cover

    Removing the Switch Cover CAUTION: Using metal tools to remove the Switch Cover may cause damage to the outer casing. The use of plastic tools or fingers is recommended to remove the Switch Cover. 1. See “Removing the Battery Pack” on page 44. 2.

  • Page 66: Removing The Keyboard

    Removing the Keyboard 1. See “Removing the Switch Cover” on page 55. 2. Pry up the centre of the Keyboard and rotate it upward away from the Upper Cover. 3. Turn the keyboard over on to the TouchPad area to expose the FFC connector. 4.

  • Page 67: Removing The Lcd Module

    Removing the LCD Module 1. See “Removing the Keyboard” on page 56. 2. Turn the computer over. Remove the two securing screws from the bottom of the chassis. Step Size Quantity Screw Type LCD Module M2.5*8 3. Remove the Antenna Cables from the cable channel as shown. Ensure that the cables are free from all cable clips.

  • Page 68

    4. Stand the computer on the LCD Panel and pull the Antenna cables completely through the chassis. 5. Disconnect the LCD cable from the Mainboard and remove the cable from the cable channel. 6. Remove the white Antenna cable from the cable channel. Ensure that the cable is completely free of the retaining clips all the way to the hinge well.

  • Page 69

    7. Remove the adhesive tape securing the Antenna cable to the Upper Cover. 8. Remove the black Antenna cable from the cable channel as shown. Ensure that the cable is completely free of the retaining clips all the way to the hinge well. 9.

  • Page 70

    12. Remove the four securing screws (two each side) from the LCD module. Step Size Quantity Screw Type LCD Module M2.5*8 13. Remove the left and right screw covers from on top of the hinges 14. Lift the LCD Module clear of the Upper Cover. Chapter 3...

  • Page 71: Removing The Upper Cover

    Removing the Upper Cover 1. See “Removing the LCD Module” on page 57. 2. Turn the computer over. Remove the eleven screws on the bottom panel. Step Size Quantity Screw Type Upper Cover M2.5*8 3. Turn the computer over. Remove the three screw caps at the rear of the Upper Cover as shown. Chapter 3...

  • Page 72

    4. Disconnect the following four cables from the Mainboard. Chapter 3...

  • Page 73

    5. Disconnect A as shown. 6. Disconnect C as shown. 7. Release the locking latch on B and remove the FFC cable as shown. 8. Release the locking latch on D and remove the FFC cable as shown. NOTE: Avoid pulling on cables directly to prevent damage to the connectors. NOTE: Use the pull-tabs on FFCs whenever available to prevent damage.

  • Page 74

    9. Remove the nine screws on the top panel. Step Size Quantity Screw Type Upper Cover M2.5*8 10. Starting at the rear left side of the cover, pry apart the Upper and Lower Covers as shown. Work along the back edge of the casing to the right as shown, then lift the Upper Cover clear of the Lower Cover.

  • Page 75: Removing The Power Board

    Removing the Power Board 1. See “Removing the Upper Cover” on page 61. 2. Locate the Power Board on the Upper Cover as shown. 3. Remove the two screws securing the Power Board to the Upper Cover. Step Size Quantity Screw Type Power Board M2*3...

  • Page 76: Removing The Left Speaker Module

    Removing the Left Speaker Module 1. See “Removing the Upper Cover” on page 61. 2. Locate the Left Speaker Module on the Upper Cover as shown. 3. Remove the adhesive tape from the Speaker cable. 4. Remove the Speaker cable from the cable channel. Ensure that the cable is free from all cable clips. Chapter 3...

  • Page 77

    5. Remove the single securing screw from the Left Speaker Module. Step Size Quantity Screw Type Left Speaker M2*3 Module 6. Lift the Speaker clear of the Upper Cover, left side first as shown. Chapter 3...

  • Page 78: Removing The Right Speaker Module

    Removing the Right Speaker Module 1. See “Removing the Upper Cover” on page 61. 2. Locate the Right Speaker Module on the Upper Cover as shown. 3. Turn the Upper Cover over and remove the Right Speaker Module cable from the cable channel. Ensure that the cable is free from all cable clips.

  • Page 79

    5. Remove the single securing screw from the Right Speaker Module. Step Size Quantity Screw Type Right Speaker M2*3 Module 6. Lift the Speaker clear of the Upper Cover, right side first as shown. Chapter 3...

  • Page 80: Removing The Touchpad Bracket

    Removing the TouchPad Bracket IMPORTANT: The TouchPad Board cannot be removed individually. To replace the TouchPad Board, replace the entire Upper Cover. 1. See “Removing the Upper Cover” on page 61. 2. Lift the FFC to detach the adhesive securing the cable to the Upper Cover. 3.

  • Page 81

    4. Remove the two screws from TouchPad bracket. Step Size Quantity Screw Type TouchPad Bracket M2*3 5. Lift the rear edge of the TouchPad bracket first to clear the securing clips and remove it as shown. Chapter 3...

  • Page 82: Removing The Mainboard

    Removing the Mainboard 1. See “Removing the Upper Cover” on page 61. 2. Remove the single securing screw from the Mainboard. Step Size Quantity Screw Type Mainboard M2.5*4 3. Lift the mainboard from the chassis, right edge first, and place it on a clean, dust-free surface. Chapter 3...

  • Page 83: Removing The Rtc Battery

    Removing the RTC Battery IMPORTANT:Follow local regulations for disposal of all batteries. The RTC Battery is soldered to the Mainboard. To replace the battery, solder the new battery to the connections shown. Chapter 3...

  • Page 84: Removing The Thermal Module

    Removing the Thermal Module 1. See “Removing the Lower Covers” on page 46. 2. Turn the Mainboard over to access the Thermal Module. 3. Remove the four securing screws (in reverse numerical order from screw 4 to screw 1) from the Thermal Module.

  • Page 85

    4. Using both hands, lift the Thermal Module clear of the Mainboard. Chapter 3...

  • Page 86: Removing The Cpu Fan

    Removing the CPU Fan 1. See “Removing the Thermal Module” on page 74. 2. Disconnect the Fan cable from the Mainboard as shown. 3. Remove the three securing screws from the Fan Module. Step Size Quantity Screw Type CPU Fan M2*3 Chapter 3...

  • Page 87

    4. Lift the CPU Fan clear of the Mainboard as shown. Chapter 3...

  • Page 88: Removing The Cpu

    Removing the CPU IMPORTANT: The pins on the underside of the CPU are very delicate. If they are damaged, the CPU may malfunction. Place the CPU on a clean, dry surface when it is not installed. 1. See “Removing the Thermal Module” on page 74. 2.

  • Page 89: Lcd Module Disassembly Process, Lcd Module Disassembly Flowchart

    LCD Module Disassembly Process LCD Module Disassembly Flowchart Remove LCD Panel from Main Unit before proceeding Remove LCD Bezel Remove Remove LCD Panel Camera Module Remove Remove Remove LCD Brackets LCD FPC Cable Antennas Screw List Step Screw Quantity Part No. LCD Bezel M2.5*6 86.N2802.002...

  • Page 90: Removing The Lcd Bezel

    Removing the LCD Bezel 1. See “Removing the LCD Module” on page 57. 2. Remove the two upper and two lower bezel screw caps and screws. Step Size Quantity Screw Type LCD Bezel M2.5*6 3. Starting from the bottom edge of the bezel, pry the bezel upwards and away from the panel. Work along the right side toward the top of the bezel, prying the covers apart.

  • Page 91: Removing The Camera Module

    Removing the Camera Module 1. See “Removing the LCD Bezel” on page 80. 2. Locate the Camera Module at the top of the LCD Module and disconnect the camera cable. 3. Remove the Camera from the module. Chapter 3...

  • Page 92: Removing The Lcd Panel

    Removing the LCD Panel 1. See “Removing the Camera Module” on page 81. 2. Remove the two securing screws from the LCD Panel. Step Size Quantity Screw Type LCD Panel M2.5*6 3. Remove the adhesive strip holding the cables in place. 4.

  • Page 93

    5. Lift the LCD Panel clear of the module. Chapter 3...

  • Page 94: Removing The Lcd Brackets And Fpc Cable

    Removing the LCD Brackets and FPC Cable 1. See “Removing the LCD Panel” on page 82. 2. Remove the six securing screws (three on each side) from the LCD Panel brackets. Step Size Quantity Screw Type LCD Brackets M2*3 3. Remove the LCD brackets by pulling away from the LCD Panel. Chapter 3...

  • Page 95

    4. Turn the LCD panel over to expose the rear. Lift the adhesive protector and disconnect the cable from the LCD Panel. 5. Lift the cable as shown to disengage the adhesive strip securing it in place. 6. Lift the FPC cable to disengage the remaining adhesive and remove the cable from the panel. Chapter 3...

  • Page 96: Removing The Antennas

    Removing the Antennas 1. See “Removing the LCD Panel” on page 82. 2. Remove the adhesive strips holding the left antenna cable in place. Ensure the cable is free from obstructions. 3. Remove the cable from the cable channel. Ensure that the cable is free from all cable clips and adhesive strips. 4.

  • Page 97

    5. Lift the left Antenna clear of the cover. 6. Remove the adhesive strips holding the right antenna cable in place. Ensure the cable is free from obstructions. 7. Remove the cable from the cable channel. Ensure that the cable is free from all cable clips and adhesive strips. Chapter 3...

  • Page 98

    8. Remove the adhesive tape securing the right Antenna to the LCD Module. 9. Lift the right Antenna clear of the cover. Chapter 3...

  • Page 99: Lcd Module Reassembly Procedure, Replacing The Antennas

    LCD Module Reassembly Procedure Replacing the Antennas 1. Replace the right Antenna as shown. Ensure that the locating pins on the Antenna are correctly seated. Locating Pin Locating Pin 2. Replace the adhesive strip to secure the Antenna 3. Run the cable down the side of the LCD Module in place.

  • Page 100

    5. Replace the left Antenna as shown. Ensure that the locating pins on the Antenna are correctly seated. Locating Pin Locating Pin 6. Replace the adhesive strip to secure the Antenna 7. Run the cable down the side of the LCD Module in place.

  • Page 101

    9. The Antennas and cables appear as shown when correctly installed. Chapter 3...

  • Page 102: Replacing The Lcd Panel

    Replacing the LCD Panel 1. Connect the LCD cable to the panel connector as 2. Press down the adhesive strip to secure the cable shown. in place. 3. Run the cable along the back of the panel and 4. Run the cable across the back of the panel as press down as indicated to secure the cable in shown and press down as indicated to secure the place.

  • Page 103

    5. Align the LCD brackets with the screw holes on the panel. Replace the six screws (three on each side) in the brackets as shown. 6. Place the LCD Panel in the LCD Module, top edge first, and secure the LCD cable with adhesive tape. IMPORTANT: Ensure that the LCD power cable passes through the hinge well and is not trapped under the panel.

  • Page 104: Replacing The Camera Module

    7. Replace the Camera cable cluster in the LCD 8. Secure the LCD module with the two securing Module. screws. Replacing the Camera Module 1. Place the camera in the LCD Module. 2. Connect the cable to the camera module. Chapter 3...

  • Page 105: Replacing The Lcd Bezel

    Replacing the LCD Bezel 1. Replace the bezel and press down until there are no gaps between the bezel and the LCD Module. IMPORTANT: Ensure that the LCD cables pass through the hinge wells and are not trapped by the bezel. Chapter 3...

  • Page 106

    2. Replace the four screws and screw caps provided. Chapter 3...

  • Page 107: Main Module Reassembly Procedure, Replacing The Cpu

    Main Module Reassembly Procedure Replacing the CPU IMPORTANT: The CPU has a Pin1 locator that must be positioned corresponding to the marker on the CPU socket. 1. Place the CPU into the CPU socket as shown, taking note of the Pin1 locator. Socket Pin1 Locator Pin1 Locator...

  • Page 108: Replacing The Cpu Fan, Replacing The Thermal Module

    Replacing the CPU Fan 1. Align the screw holes on the CPU Fan and 2. Replace the three screws to secure the Fan to the Mainboard and replace the Fan. Mainboard. 3. Connect the Fan power cable to the Mainboard connector. Replacing the Thermal Module IMPORTANT: Apply a suitable thermal grease and ensure all heat pads are in place before replacing the Thermal Module.

  • Page 109: Replacing The Mainboard

    3. Align the screw holes on the Thermal Module and 4. Replace the four securing screws (in numerical Mainboard then replace the module. Keep the order from screw 1 to screw 4) to secure the module as level as possible to spread the thermal Thermal Module in place.

  • Page 110: Replacing The Touchpad Bracket

    Replacing the TouchPad Bracket 1. Replace the TouchPad bracket top edge first to 2. Press the bracket down to engage the securing engage the securing clips. clips. 3. Replace the two screws to secure the TouchPad Bracket to the Upper Cover. 4.

  • Page 111

    5. Replace the FFC and press down as indicated to secure it to the Upper Cover. Chapter 3...

  • Page 112: Replacing The Right Speaker Module

    Replacing the Right Speaker Module 1. Place the module left side first on the Upper Cover 2. Replace the single screw to secure the module in as shown. Ensure that the left side of the module is place. seated correctly in the securing clip. 3.

  • Page 113: Replacing The Left Speaker Module

    Replacing the Left Speaker Module 1. Place the module right side first on the Upper 2. Replace the single screw to secure the module in Cover as shown. Ensure that the right side of the place. module is seated correctly in the securing clip. 3.

  • Page 114: Replacing The Power Board, Replacing The Upper Cover

    Replacing the Power Board 1. Slide the Power Board in to the Upper Cover front edge first to engage the securing clip. 2. Press the board down to locate the securing pin. 3. Replace the two screws to secure the board to the Upper Cover.

  • Page 115

    2. Press down around the edges to secure it in place. 3. Replace the nine screws in the Upper Cover as shown. Chapter 3...

  • Page 116

    4. Replace the three screw caps as shown. 5. Connect the following cables to the Mainboard. Chapter 3...

  • Page 117

    6. Connect A as shown. 7. Connect C as shown. 8. Connect B and close the locking latch to secure the cable in place. 9. Connect D and close the locking latch to secure the cable in place. Chapter 3...

  • Page 118: Replacing The Lcd Module

    10. Turn the computer over and replace the eleven screws as shown. Replacing the LCD Module 1. Align the screw holes on the LCD Module and 2. The left and right screw covers are shaped Upper Cover and replace the LCD Module. differently.

  • Page 119

    4. Replace the right screw cover as shown. Ensure that the securing tab on the rear of the cover is seated correctly in the Upper Cover. 5. Replace the four screws securing the LCD Module to the Upper Cover. 6. Ensure that the Hinge Covers are replaced 7.

  • Page 120

    9. Run the black Antenna cable along the cable 10. Replace the adhesive strip to secure the cable in channel as shown using all available retaining place. clips. 11. Run the white Antenna cable along the cable channel as shown using all available retaining clips. 12.

  • Page 121

    14. Stand the computer on the LCD Panel and pass the Antenna cables through the chassis. 15. The Upper Cover appears as shown when the Antenna and LCD cables are correctly installed. 16. Turn the computer over. Run the Antenna cables along the cable channel as shown, using all available cable clips.

  • Page 122

    17. Replace the two screws securing the LCD Module to the Lower Cover. Chapter 3...

  • Page 123: Replacing The Keyboard

    Replacing the Keyboard 1. Connect the Keyboard FFC to the Mainboard and close the locking latch to secure the cable in place. 2. Turn the Keyboard over and insert it front edge first 3. Press down as indicated to secure the Keyboard in into the chassis.

  • Page 124: Replacing The Switch Cover, Replacing The Hard Disk Drive Module

    Replacing the Switch Cover 1. Place the Switch Cover left side first on to the Upper Cover. 2. Press down as indicated to snap the Switch Cover into place. Replacing the Hard Disk Drive Module 1. Place the HDD in the HDD carrier. 2.

  • Page 125

    3. Insert the HDD, as indicated and lower it into 4. Slide the HDD in the direction of the arrow to place. connect the interface. Chapter 3...

  • Page 126: Replacing The Wlan Module, Replacing The Dimm Modules

    Replacing the WLAN Module 1. Insert the WLAN Module into the WLAN socket. 2. Replace the two screws to secure the module. 3. Connect the two Antenna cables to the module. 4. After connecting the cables to the terminals, secure the cables in place with adhesive tape to NOTE: The black cable connects to the upper avoid trapping.

  • Page 127: Replacing The Odd Module, Replacing The Lower Covers

    Replacing the ODD Module 1. Press the bezel into the tray, bottom edge first, to 2. Secure the ODD bracket with the two screws. secure it to the ODD Module. 3. Push the ODD Module into the ODD bay until it is 4.

  • Page 128: Replacing The Sd Dummy Card

    3. Replace the three screws to secure the covers in place. Memory Cover Cover Replacing the SD Dummy Card 1. Insert the SD Dummy Card into the slot as shown. 2. Push until the card clicks into place and is flush with the casing.

  • Page 129: Replacing The Battery

    Replacing the Battery 1. Slide and hold the battery release latch to the 2. Slide the battery lock in the direction shown to release position (1), insert the battery pack and secure the battery in place. press down (2). Chapter 3...

  • Page 130

    Chapter 3...

  • Page 131: Common Problems

    Chapter 4 Troubleshooting Common Problems Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. Obtain the failing symptoms in as much detail as possible.

  • Page 132: Power On Issue

    Power On Issue If the system doesn’t power on, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Computer Shutsdown Intermittently If the system powers off at intervals, perform the following actions one at a time to correct the problem. Check the power cable is properly connected to the computer and the electrical outlet.

  • Page 133: No Display Issue

    No Display Issue If the Display doesn’t work, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: No POST or Video If the POST or video doesn’t display, perform the following actions one at a time to correct the problem. Make sure that the internal display is selected.

  • Page 134: Random Loss Of Bios Settings

    Abnormal Video Display If video displays abnormally, perform the following actions one at a time to correct the problem. Reboot the computer. If permanent vertical/horizontal lines or dark spots display in the same location, the LCD is faulty and should be replaced. See “Disassembly Process” on page 42. If extensive pixel damage is present (different colored spots in the same locations on the screen), the LCD is faulty and should be replaced.

  • Page 135: Lcd Failure, Built-in Keyboard Failure

    LCD Failure If the LCD fails, perform the following actions one at a time to correct the problem. Do not replace a non- defective FRUs: Built-In Keyboard Failure If the built-in Keyboard fails, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Chapter 4...

  • Page 136: Touchpad Failure, Internal Speaker Failure

    TouchPad Failure If the TouchPad doesn’t work, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Internal Speaker Failure If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Chapter 4...

  • Page 137

    Sound Problems If sound problems are experienced, perform the following actions one at a time to correct the problem. Reboot the computer. Navigate to Start Control Panel System and Maintenance System Device Manager. Check the Device Manager to determine that: •...

  • Page 138: Hdd Not Operating Correctly

    HDD Not Operating Correctly If the HDD does not operate correctly, perform the following actions one at a time to correct the problem. Disconnect all external devices. Run a complete virus scan using up-to-date software to ensure the computer is virus free. Run the Windows Vista Startup Repair Utility: insert the Windows Vista Operating System DVD in the ODD and restart the computer.

  • Page 139: Odd Failure

    ODD Failure If the ODD fails, perform the following actions one at a time to correct the problem. Do not replace a non- defective FRUs: ODD Not Operating Correctly If the ODD exhibits any of the following symptoms it may be faulty: •...

  • Page 140

    Double-click lDE ATA/ATAPI controllers. If a device displays a down arrow, right-click on the device and click Enable. Double-click DVD/CD-ROM drives. If the device displays a down arrow, right-click on the device and click Enable. Check that there are no yellow exclamation marks against the items in lDE ATA/ATAPI controllers. If a device has an exclamation mark, right-click on the device and uninstall and reinstall the driver.

  • Page 141

    Double-click IDE ATA/ATAPI controllers, then right-click ATA Device 0. Click Properties and select the Advanced Settings tab. Ensure that the Enable DMA box is checked and click OK. Repeat for the other ATA Devices shown if applicable. Drive Not Detected If Windows cannot detect the drive, perform the following actions one at a time to correct the problem.

  • Page 142: Wireless Function Failure, Thermal Unit Failure

    Wireless Function Failure If the WLAN fails, perform the following actions one at a time to correct the problem. Do not replace a non- defective FRUs: Thermal Unit Failure If the Thermal Unit fails, perform the following actions one at a time to correct the problem. Do not replace a non-defective FRUs: Chapter 4...

  • Page 143: External Mouse Failure, Other Failures

    External Mouse Failure If an external Mouse fails, perform the following actions one at a time to correct the problem. Try an alternative mouse. If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See the mouse user manual.

  • Page 144: Intermittent Problems, Undetermined Problems

    Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: Run the advanced diagnostic test for the system board in loop mode at least 10 times.

  • Page 145: Post Codes

    Post Codes These tables describe the POST codes and descriptions during the POST. Code Beeps POST Routine Description Verify Real Mode Disable Non-Maskable Interrupt (NMI) Get CPU type Initialize system hardware Initialize chipset with initial POST values Set IN POST flag Initialize CPU registers Enable CPU cache Initialize caches to initial POST values...

  • Page 146

    Code Beeps POST Routine Description POST device initialization 2-1-2-3 Check ROM copyright notice Check video configuration against CMOS Initialize PCI bus and devices Initialize all video adapters in system QuietBoot start (optional) Shadow video BIOS ROM Display BIOS copyright notice Display CPU type and speed Initialize EISA board Test keyboard...

  • Page 147

    Code Beeps POST Routine Description Initialize Extended BIOS Data Area Test and initialize PS/2 mouse Initialize floppy controller Determine number of ATA drives (optional) Initialize hard-disk controllers Initialize local-bus hard-disk controllers Jump to UserPatch2 Build MPTABLE for multi-processor boards Install CD ROM for boot Clear huge ES segment register Fixup Multi Processor table Search for option ROMs.

  • Page 148

    Code Beeps POST Routine Description PnPnd dual CMOS (optional) Initialize notebook docking (optional) Initialize notebook docking late Force check (optional) Extended checksum (optional) Unknown interrupt Code Beeps For Boot Block in Flash ROM Initialize the chipset Initialize the bridge Initialize the CPU Initialize system timer Initialize system I/O Check force recovery boot...

  • Page 149: Jumper And Connector Locations, Top View

    Chapter 5 Jumper and Connector Locations Top View Item Description JLVDS1 LCD Connector JP14 Power/B Connector JSPK1 Speaker(Left) Connector JSPK2 Speaker(Right) Connector JKB1 Internal Keyboard Connector JTP1 Touch Pad Connector South Bridge Touch pad (Left) Button Touch pad (Right) Button Chapter 5...

  • Page 150: Bottom View

    Bottom View ITEM DESCRIPTION PJP1 AC-IN Connector JRJ1 RJ45 Connector JCRT1 CRT Connector JP12 Fan Connector JUSB1 USB Connector JUSB2 USB Connector JMIC1 MIC-In Jack JHP1 Head-Phone Jack JSATA2 HDD Connector North Bridge JCPU1 CPU Socket JREAD1 Card Reader Socket PJP2 Battery Connector JDIMM2...

  • Page 151: Power Board

    Power Board ITEM DESCRIPTION Lid Switch TP Lock Button ON/OFF Button Wireless Button LED1 ON/OFF LED LED3 Media LED LED4 Num LED LED5 Wireless LED LED6 Caps LED LED7 TP Lock LED Chapter 5...

  • Page 152: Clearing Password Check And Bios Recovery, Clearing Password Check, Clear Cmos Jumper

    Clearing Password Check and BIOS Recovery This section provides you with the standard operating procedures of clearing password and BIOS recovery for eMachines E627. The machine provides one Hardware Open Gap on main board for clearing password check, and one Hotkey for enabling BIOS Recovery.

  • Page 153: Bios Recovery By Crisis Disk

    BIOS Recovery by Crisis Disk BIOS Recovery Boot Block: BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous BIOS flashing process failed.

  • Page 154

    Chapter 5...

  • Page 155: Fru (field Replaceable Unit) List

    Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of eMachines E627. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel.

  • Page 156: Emachines E627 Exploded Diagrams, Main Assembly

    E627 Exploded Diagrams Main Assembly Chapter 6...

  • Page 157

    Description Acer P/N Middle Cover 60.N2802.003 Assy Hinge Cap 42.N2802.001 Assy Upper Case 60.N2802.001 Assy Mainboard MB.N6502.001 Lower Case 60.N2802.002 Chapter 6...

  • Page 158: Base Assembly

    Base Assembly Description Acer P/N 23.N2802.001 Thermal Module 60.N6502.001 Mainboard MB.N6502.001 Chapter 6...

  • Page 159: Rear Assembly

    Rear Assembly Description Acer P/N RAM Door 42.N2802.004 HDD Door 42.N2802.005 Lower Case 60.N2802.002 Chapter 6...

  • Page 160: Emachines E627 Fru List

    E627 FRU List CATEGORY Description AcerPN Board POWER BOARD 55.N2802.001 WLAN CARD-XB63 NI.23600.007 WLAN CARD-BCM4312 NI.23600.029 Cable TP FFC 50.N2802.001 POWER CORD US 3 PIN 27.TAVV5.001 POWER CORD EU 3 PIN 27.TAVV5.002 POWER CORD AUS 3 PIN 27.TAVV5.003 POWER CORD UK 3 PIN 27.TAVV5.004...

  • Page 161

    CATEGORY Description AcerPN LOWER CASE 60.N2802.002 TP BRACKET 33.N2802.001 MIDDLE COVER ASSY 60.N2802.003 HINGE CAP ASSY 42.N2802.001 UP CAP R 42.N2802.002 UP CAP L 42.N2802.003 RAM DOOR ASSY 42.N2802.004 HDD DOOR ASSY 42.N2802.005 Chapter 6...

  • Page 162

    CATEGORY Description AcerPN HDD SEAGATE 2.5" 5400rpm 160GB ST9160310AS KH.16001.034 Crockett SATA LF F/W:0303 HDD TOSHIBA 2.5" 5400rpm 160GB MK1655GSX Libra KH.16004.006 SATA LF F/W: FG011J HDD HGST 2.5" 5400rpm 160GB HTS543216L9A300 KH.16007.019 Falcon-B SATA LF F/W:C40C HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO KH.16008.022 ML160 SATA LF F/W:11.01A11 HDD SEAGATE 2.5"...

  • Page 163

    CATEGORY Description AcerPN ODD BEZEL-SUPER MULTI 42.N2802.006 ODD BRACKET 33.N2802.003 Keyboard Keyboard EM-7T HM50/70 Internal 17 Standard 99KS KB.I1700.438 Black US International Keyboard EM-7T HM50/70 Internal 17 Standard 99KS KB.I1700.423 Black Greek Keyboard EM-7T HM50/70 Internal 17 Standard 99KS KB.I1700.414 Black Arabic Keyboard EM-7T HM50/70 Internal 17 Standard 99KS KB.I1700.430...

  • Page 164

    CATEGORY Description AcerPN ASSY LCD MODULE 15.6 IN. WXGA GLARE W/ 6M.N2802.001 ANTENNA*2, CCD 0.3M LCD AUO 15.6" WXGA Glare B156XW01-V0 LF 220nit LK.15605.001 CCFL LCD AUO 15.6"W WXGA Glare B156XW01 V0 1A LK.15605.002 LF 220nit 8ms 500:1 CCFL LCD SAMSUNG 15.6"W WXGA Glare LK.15606.001 LTN156AT01-A01 LF 220nit 8ms 600:1 CCFL LCD LPL 15.6"...

  • Page 165

    CATEGORY Description AcerPN ASSY LCD MODULE 15.6 IN. WXGA GLARE W/O CCD 6M.N3202.001 LCD AUO 15.6" WXGA Glare B156XW01-V0 LF 220nit LK.15605.001 CCFL LCD AUO 15.6"W WXGA Glare B156XW01 V0 1A LK.15605.002 LF 220nit 8ms 500:1 CCFL LCD SAMSUNG 15.6"W WXGA Glare LK.15606.001 LTN156AT01-A01 LF 220nit 8ms 600:1 CCFL LCD LPL 15.6"...

  • Page 166

    CATEGORY Description AcerPN ASSY LCD MODULE 15.6 IN. WXGA GLARE W/ 6M.N3202.001 ANTENNA*2, W/O CCD LCD AUO 15.6" WXGA Glare B156XW01-V0 LF 220nit LK.15605.001 CCFL LCD AUO 15.6"W WXGA Glare B156XW01 V0 1A LK.15605.002 LF 220nit 8ms 500:1 CCFL LCD SAMSUNG 15.6"W WXGA Glare LK.15606.001 LTN156AT01-A01 LF 220nit 8ms 600:1 CCFL LCD LPL 15.6"...

  • Page 167

    60.N2802.004 ANTENNA-AUX 50.N2802.002 ANTENNA-MAIN 50.N2802.003 ANTENNA-MAIN+MIMO 50.N2802.004 LCD BEZEL FOR W/O CCD F 60.N3202.001 LED CABLE FOR W/O CCD F 50.N3202.002 LCD BRACKET R&L FOR LCD 33.N2802.005 Mainboard Mainboard E627 ATI RS780 SB710 8132 V1.0 LF MB.N6502.001 Memory Chapter 6...

  • Page 168

    CATEGORY Description AcerPN Memory NANYA SO-DIMM DDRII 667 1GB KN.1GB03.026 NT1GT64UH8D0FN-3C LF 64*16 0.07um Memory MICRON SO-DIMM DDRII 667 1GB KN.1GB04.010 MT8HTF12864HDY-667G1 LF 64*16 0.065um Memory ELPIDA SO-DIMM DDRII 667 1GB KN.1GB09.008 EBE11UE6ACUA-6E-E LF 64*16 0.065um Memory SAMSUNG SO-DIMM DDRII 667 1GB KN.1GB0B.027 M470T2864EH3-CE6 LF 64*16 0.055um Memory HYNIX SO-DIMM DDRII 667 1GB...

  • Page 169

    Chapter 6...

  • Page 170: Model Definition And Configuration

    Appendix A Model Definition and Configuration Model Country Acer Part No Description eME627- Spain LX.N6502.041 eME627-204G50Mi W7HP64EeTES1 AATF20 204G50Mi UMACkk 2*2G/500_L/6L2.2/5R/ CB_bg_0.3D_N_HG_ES51 eME627- Holland LX.N6502.039 eME627-203G25Mi W7HP64EeTNL1 AATF20 203G25Mi UMACkk 2G+1G/250/6L2.2/5R/ CB_bg_0.3D_HG_NL11 eME627- Norway LX.N6502.040 eME627-203G25Mi W7HP64EeTNO1 AATF20 203G25Mi UMACkk 2G+1G/250/6L2.2/5R/ CB_bg_0.3D_HG_NO11 eME627- Denmark...

  • Page 171

    Model Country Acer Part No Description eME627- Luxembourg LX.N6502.035 eME627-203G25Mi W7HP64EeTLU3 AATF20 203G25Mi UMACkk 2G+1G/250/6L2.2/5R/ CB_bg_0.3D_HG_IT41 eME627- Switzerland LX.N6502.018 eME627-203G25Mi W7HP64EeTCH1 AATF20 203G25Mi UMACkk 2G+1G/250/6L2.2/5R/ CB_bg_0.3D_HG_IT41 eME627- Algeria LX.N6502.008 eME627-203G25Mi EM AATF20 203G25Mi W7HP64EMeTDZ1 UMACkk 2G+1G/ 250/6L2.2/5R/CB_bg_0.3D_HG_ES81 eME627- Middle East LX.N6502.009 eME627-203G25Mi EM AATF20...

  • Page 172

    Model Country Acer Part No Description eME627- South Africa LX.N6502.007 eME627-203G25Mi EM AATF20 203G25Mi W7HP64EMeTZA2 UMACkk 2G+1G/ 250/6L2.2/5R/CB_bg_0.3D_HG_ES61 eME627- Middle East LX.N6502.010 eME627-203G25Mi EM AATF20 203G25Mi W7HP64EMeTME6 UMACkk 2G+1G/ 250/6L2.2/5R/CB_bg_0.3D_HG_ES61 eME627- Eastern LX.N6502.022 eME627-203G25Mi W7HP64EeTEU5 AATF20 203G25Mi Europe UMACkk 2G+1G/250/6L2.2/5R/ CB_bg_0.3D_HG_RO11 eME627- Eastern...

  • Page 173

    Model Country Acer Part No Description eME627- Australia/ LX.N650X.004 eME627-6C2G32Mi VHP32eTAU1 AATK42 6C2G32Mi UMACkk 1*2G/320/6L2.2/5R/ Zealand CB_bg_0.3D_HG_EN13 eME627- Australia/ LX.N650X.006 eME627-202G25Mi VHP32eTAU1 AATF20 202G25Mi UMACkk 1*2G/250/6L2.2/5R/ Zealand CB_bg_0.3D_HG_EN13 eME627- Australia/ LX.N650X.002 eME627-204G16Mi VHP32eTAU1 AATF20 204G16Mi UMACkk 2*2G/160/6L2.2/5R/ Zealand CB_bg_0.3D_HG_EN13 eME627- Australia/ LX.N650X.001 eME627-204G25Mi VHP32eTAU1...

  • Page 174

    Model Country Acer Part No Description eME627- Canada LX.N6402.005 eME627-312G25Mi W7HP64eTCA2 AAL310 312G25Mi UMAkk 2*1G/250/6L2.2/5R/ CB_bg_HG_FR81 eME627- Canada LX.N6402.007 eME627-312G16Mi W7HP64eTCA2 AAL310 312G16Mi UMAkk 2*1G/160/6L2.2/5R/ CB_bg_HG_FR81 eME627- Canada LX.N6402.001 eME627-202G16Mi W7HP64eTCA2 AATF20 202G16Mi UMAkk 2*1G/160/6L2.2/5R/ CB_bg_HG_FR81 eME627- Canada LX.N6402.003 eME627-313G16Mi W7HP64eTCA2 AAL310 313G16Mi UMAkk 2G+1G/160/6L2.2/5R/...

  • Page 175

    Model VGA Chip VRAM 1 Memory 1 Memory 2 eME627-203G25Mi N15.6WXGAG SO2GBII6 SO1GBII6 eME627-203G25Mi N15.6WXGAG SO2GBII6 SO1GBII6 eME627-203G25Mi N15.6WXGAG SO2GBII6 SO1GBII6 eME627-203G25Mi N15.6WXGAG SO2GBII6 SO1GBII6 eME627-203G25Mi N15.6WXGAG SO2GBII6 SO1GBII6 eME627-203G25Mi N15.6WXGAG SO2GBII6 SO1GBII6 eME627-203G25Mi N15.6WXGAG SO2GBII6 SO1GBII6 eME627-203G25Mi N15.6WXGAG SO2GBII6 SO1GBII6 eME627-203G25Mi N15.6WXGAG...

  • Page 176

    Model VGA Chip VRAM 1 Memory 1 Memory 2 eME627-312G16Mi N15.6WXGAG SO1GBII6 SO1GBII6 eME627-312G25Mi N15.6WXGAG SO1GBII6 SO1GBII6 eME627-312G16Mi N15.6WXGAG SO1GBII6 SO1GBII6 eME627-202G16Mi N15.6WXGAG SO1GBII6 SO1GBII6 eME627-312G25Mi N15.6WXGAG SO1GBII6 SO1GBII6 eME627-312G16Mi N15.6WXGAG SO1GBII6 SO1GBII6 eME627-202G16Mi N15.6WXGAG SO1GBII6 SO1GBII6 eME627-313G16Mi N15.6WXGAG SO2GBII6 SO1GBII6 eME627-313G16Mi N15.6WXGAG...

  • Page 177

    Media Extra Model Card Reader 1(GB) 2(GB) Processor eME627-203G25Mi N250GB NSM8XS 5 in 1-Build in 5.4KS eME627-203G25Mi N250GB NSM8XS 5 in 1-Build in 5.4KS eME627-203G25Mi N250GB NSM8XS 5 in 1-Build in 5.4KS eME627-203G25Mi N250GB NSM8XS 5 in 1-Build in 5.4KS eME627-203G25Mi N250GB NSM8XS...

  • Page 178

    Media Extra Model Card Reader 1(GB) 2(GB) Processor eME627-203G25Mi N250GB NSM8XS 5 in 1-Build in 5.4KS eME627-202G25Mi N250GB NSM8XS 5 in 1-Build in 5.4KS eME627-202G16Mi N160GB NSM8XS 5 in 1-Build in 5.4KS eME627-202G16Mi N160GB NSM8XS 5 in 1-Build in 5.4KS eME627-202G25Mi N250GB NSM8XS...

  • Page 179

    Media Extra Model Card Reader 1(GB) 2(GB) Processor eME627-312G25Mi N250GB NSM8XS 5 in 1-Build in 5.4KS eME627-312G16Mi N160GB NSM8XS 5 in 1-Build in 5.4KS eME627-202G16Mi N160GB NSM8XS 5 in 1-Build in 5.4KS eME627-312G25Mi N250GB NSM8XS 5 in 1-Build in 5.4KS eME627-312G16Mi N160GB NSM8XS...

  • Page 180

    Wireless Wireless Model Bluetooth LAN1 eME627-203G25Mi 3rd WiFi BG 3rd WiFi BG eME627-203G25Mi 3rd WiFi BG 3rd WiFi BG eME627-203G25Mi 3rd WiFi BG 3rd WiFi BG eME627-203G25Mi 3rd WiFi BG 3rd WiFi BG eME627-203G25Mi 3rd WiFi BG 3rd WiFi BG eME627-203G25Mi 3rd WiFi BG 3rd WiFi BG...

  • Page 181

    Wireless Wireless Model Bluetooth LAN1 eME627-312G16Mi 3rd WiFi BG 3rd WiFi BG eME627-312G25Mi 3rd WiFi BG 3rd WiFi BG eME627-312G16Mi 3rd WiFi BG 3rd WiFi BG eME627-202G16Mi 3rd WiFi BG 3rd WiFi BG eME627-312G25Mi 3rd WiFi BG 3rd WiFi BG eME627-312G16Mi 3rd WiFi BG 3rd WiFi BG...

  • Page 182

    Appendix A...

  • Page 183: Test Compatible Components

    XP Pro environment. Refer to the following lists for components, adapter cards, and peripherals which have passed these tests. Regarding configuration, combination and test procedures, please refer to the eMachines E627 Compatibility Test Report released by the Acer Mobile System Testing Department.

  • Page 184

    Microsoft Windows Vista Environment Test ® ® Vendor Type Description Adapter DELTA Adapter DELTA 65W 19V 1.7x5.5x11 Yellow ADP-65JH DB A, LV5 LED LF LITE-ON Adapter LITE-ON 65W 19V 1.7x5.5x11 Yellow PA-1650- 22AC LV5 LED LF HIPRO Adapter HIPRO 65W 19V 1.7x5.5x11 Yellow HP-A0652R3B 1LF, LV5 LED LF Battery SANYO...

  • Page 185

    Vendor Type Description HGST N320GB5.4KS HDD HGST 2.5" 5400rpm 320GB HTS545032B9A300 Panther B SATA LF F/W: C60F N320GB5.4KS HDD WD 2.5" 5400rpm 320GB WD3200BEVT-22ZCT0 ML160 SATA LF F/W:11.01A11 SEAGATE N500GB5.4KS HDD SEAGATE 2.5" 5400rpm 500GB ST9500325AS Wyatt SATA LF F/W:0001SDM1 HGST N500GB5.4KS HDD HGST 2.5"...

  • Page 186

    VGA Chip None UMA (AMD) NB Chipset AMDRS780MN AMDRS780MN SB Chipset AMDSB710 AMDSB710 Keyboard eMACHINES EM-7T Keyboard eMACHINES EM-7T HM50/70 Internal 17 Standard Black Atheros AR8132L Atheros AR8132L WiFi Antenna PIFA PIFA Audio Codec Realtek ALC272X Realtek Audio Codec ALC272X...

  • Page 187: Online Support Information

    Appendix C Online Support Information This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d.

  • Page 188

    Appendix C...

  • Page 189

    Removing Replacing AFLASH Utility Display Antennas display Removing hotkeys Replacing EasyTouch Failure Battery Euro Replacing External Module Disassembly Battery Pack Flowchart Removing BIOS ROM type Features vendor Version Flash Utility 25–33 BIOS Utility FPC Cable Boot Removing Exit FRU (Field Replaceable Unit) List Navigating Onboard Device Configuration Save and Exit...

  • Page 190

    Removing ODD Failure Replacing Online Support Information LCD Brackets Optical Disk Drive Removing Replacing Replacing Optical Drive Module LCD Cable Removing Replacing LCD Failure LCD Module Panel Removing Bottom Replacing PC Card LCD Module Disassembly Power Board Flowchart Removing LCD Module Reassembly Procedure Replacing LCD Panel Power On Failure...

  • Page 191

    Removing TouchPad Bracket Removing Replacing TouchPad Failure Troubleshooting Built-in KB Failure EasyTouch Buttons HDTV Switch Internal Speakers LCD Failure No Display Other Failures Power On Thermal Unit TouchPad WLAN Undetermined Problems Upper Cover Removing Replacing utility 25–33 BIOS Windows 2000 Environment Test Wireless Function Failure WLAN Module Removing...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: