Basic Operations - Clarion WXZ468RMP Owner's Manual

Basic Operations

CT (Clock Time) function
The CT function receives CT data sent from an
RDS station and displays the time.
∗ If a CT data is not being received, "––:––CT" ap-
pears in the display.
Note:
• CT data is not transmitted in some countries and
by some broadcast stations. Also, in some areas,
the CT may not display accurately.
Setting the spectrum analyzer
pattern
∗ The factory default setting is "SCAN".
1. Each time you press the [SPE/ANA] button,
the spectrum analyzer pattern changes in the
following order:
Scan Pattern 1 to 7
* The bars in the display move downward be-
fore scanning begins.
Setting the G.EQ (Graphic Equalizer)
This adjustment can only be performed when
the DZE is set to"DZE OFF".
∗ The factory default setting is "ON".
1. Press and hold the [A-MODE] knob for 1
second or longer to turn on the G.EQ effect.
"G.EQ" appears on the display.
2. Press and hold the [A-MODE] knob for 1
second or longer to turn off the G.EQ effect.
"G.EQ OFF" appears on the display.
Setting the DZE (Digital Z-Enhancer)
This unit is provided with 3 types of sound tone
effects stored in memory. Select the one you
prefer.
∗ The factory default setting is "DZE OFF".
Each time you press the [D-Z] button, the tone
effect changes in the following order:
"DZE 1" "DZE 2"
"DZE 1" ...
• DZE 1 : suitable for the genuine speakers
• DZE 2 : suitable for separate speakers
• DZE 3 : suitable for coaxial speakers
• DZE OFF : no sound effect
Notes:
• The volume changes each time the DZE (Digital
Z-Enhancer) setting is switched.
• Sufficient effects cannot be obtained with some
speaker systems. In such cases, adjust the vol-
ume.
12
WXZ468RMP
Off Scan ...
"DZE 3" "DZE OFF"
Adjusting the tone
Press the [A-MODE] knob and select the item to
adjust. Each time you press the [A-MODE]
knob, the item changes as following order:
When "DZE 1, 2, 3" is set
"LPO" "DZE LEVEL"
"FADER" Last function mode...
When "DZE OFF" is set
"LPO" "G.EQ EDIT"
"TREBLE" "BALANCE"
Last function mode...
Note:
• The display automatically returns to the previous
mode.
Adjusting the LPO (Listening
Position Optimizer)
This is the function that virtually optimizes the
speaker distances of each type of a car to the
listening position, which realizes the clearer
soundstage.
The setting value has to be adjusted to the lis-
tening position and the type of your car.
∗ The factory default setting is "OFF".
1. Press the [A-MODE] knob and select "LPO".
2. Turn the [A-MODE] knob to select the listen-
ing position. The adjustment items you can
select are as follows: L3, L2, L1, OFF, R1,
R2, R3.
The setting value of the listening position
L: left seat, R: right seat, 1.: COMPACT (com-
pact car), 2.: SEDAN (sedan), 3.: 1 BOX (van)
3. When the adjustment is complete, press the
[A-MODE] knob several times until the func-
tion mode is reached.
Adjusting the DZE level
You can adjust the DZE level in 3 steps and reg-
ister each adjustment respectively.
This adjustment can only be performed when
the DZE is set to "DZE 1,2,3".
1. Press the [A-MODE] knob and select "DZE
LEVEL".
2. Turn the [A-MODE] knob to adjust the level.
∗ The factory default setting is "MID". (Adjust-
ment LOW/MID/HIGH)
3. When the adjustment is complete, press the
[A-MODE] knob several times until the func-
tion mode is reached.
"BALANCE"
"BASS"
"FADER"