Oki OKIOFFICE 84 User Manual page 64

telephone rings, when the telephone handset is lifted, or when
a document is loaded. Available settings are on and off.
Note: If you have purchased the optional MFP software
and you have connected your machine to a PC, it is
recommended that you turn 18:POWER SAVE MODE
off. Your PC cannot switch your machine back to full
operation.
19:ECM FUNCTION - The error correction mode function
19:ECM FUNCTION 19:ECM FUNCTION
19:ECM FUNCTION 19:ECM FUNCTION
helps your machine to improve communication in areas where
telephone line conditions are poor. Available settings are on
and off.
Note: When using ECM, the transmitting machine
automatically checks the data as it is sent. If the receiving
machine cannot verify the transmission, the transmitting
machine will retransmit as necessary. Using ECM also
increases transmission time because the data is checked
as it is transmitted.
20:REMOTE DIAGNOSIS - The remote diagnostics feature 20:REMOTE DIAGNOSIS 20:REMOTE DIAGNOSIS
20:REMOTE DIAGNOSIS 20:REMOTE DIAGNOSIS
allows a service person to remotely dial and service your
machine. Available settings are on and off.
21:PC/FAX SWITCH - When your machine is set to answer
21:PC/FAX SWITCH 21:PC/FAX SWITCH 21:PC/FAX SWITCH 21:PC/FAX SWITCH
in PC Receive Mode and your MFP software is set to receive
fax messages, all incoming calls are transferred directly to your
PC. However, if you are experiencing a problem with your PC,
you can tell your machine to receive and print faxes locally by
setting this function to on. Available settings are on and off.
64
22:NO TONER MEM. RX 22:NO TONER MEM. RX - With this function turned on, 22:NO TONER MEM. RX
22:NO TONER MEM. RX 22:NO TONER MEM. RX
your machine automatically receives and stores messages in its
memory when it the toner is low. When turned off, messages
print even if toner is low or empty. Available settings are on and
off.
Note: The off setting allows time for you to replace the
toner cartridge, but quality of printing may become poor
as the toner cartridge is exhausted.
23:MEM. FULL SAVE - With single location transmission
23:MEM. FULL SAVE 23:MEM. FULL SAVE
23:MEM. FULL SAVE 23:MEM. FULL SAVE
and 17:MEM./FEEDER SW. set to MEM and 25:INSTANT
DIALLING is set to off, and with multiple location transmission,
call origination starts after an entire document is read into
memory. If during this process memory becomes full, a MEMORY
OVERFLOW message is shown in the display and the display
changes to:
S E N D S E N D S E N D S E N D S E N D S C A N N E D S C A N N E D S C A N N E D S C A N N E D S C A N N E D
( ß ß ß ß ß ) (à à à à à ) ) ) ) )
YES YES YES ( ( ) ) ) NO NO NO ( (
YES YES ( ( ) NO NO ( (
Press the NO õ key, your machine gives an alarm, the scanning
of your document stops and the display shows:
M E M O R Y M E M O R Y O V E R F L O W O V E R F L O W
M E M O R Y M E M O R Y M E M O R Y O V E R F L O W O V E R F L O W O V E R F L O W
R E F E R R E F E R R E F E R T O T O T O U S E R U S E R U S E R
R E F E R R E F E R T O T O U S E R U S E R
Press the STOP key and the remaining pages of your document
are removed from your machine. The pages of your document
that were scanned into memory are automatically deleted from
the memory.
P A G E S P A G E S P A G E S P A G E S P A G E S
G U I D E G U I D E G U I D E
G U I D E G U I D E
OKIOFFICE 84