Kenmore 106.5114 Series Use & Care Manual page 9

• Allow 24hours t o produce thefirstbatch ofice.Discard t he
firstthree batches of iceproduced. Wait72hours f orfull
iceproduction.
The display screen onthedispenser control panel willturn
off automatically andenter " sleep" m ode when thecontrol
buttons anddispenser levers h ave notbeen used for
2 minutes or more. Whilein"sleep" m ode, thefirstpress o f
a control button willonlyreactivate thedisplay s creen,
without changing anysettings. Afterreactivation, changes to
anysettings canthen bemade. If nochanges aremade
within 2 minutes, thedisplay w illre-enter "sleep" m ode.
Dispensing Options
Your dispenser can dispense water and ice in two ways.
• The DISPENSE WATER button, located below the dispenser
control panel's display screen, dispenses only water.
• The dispenser lever is the pad located along the rear wall of
the dispenser cavity. When pressed, it dispenses either water
or ice, depending on the chosen setting.
To dispense both water and ice at the same time, select the
desired type of ice and dispense it using the dispenser lever,
then press the DISPENSE WATER button while still dispensing
ice.
The Water Dispenser
2. Press a sturdy glass against the dispenser lever.
3. Remove the glass to stop dispensing.
To Dispense Water (Measured Fill):
Measured Fill allows you to dispense a specified amount of
water with the touch of a few buttons.
NOTE: The amount of water you select will be dispensed. Be
sure that the container is empty and can hold the entire volume.
If ice is in the container, you may need to adjust your selection.
IMPORTANT: Low water pressure may affect the accuracy of
this feature.
1. Press MEASURED FILL to turn the feature on. When the
feature is on, the Measured Fill screen appears on the
display.
IMPORTANT:
• Dispense at least 1 qt (1 L) of water every week to maintain a
fresh supply.
• If the flow of water from the dispenser decreases, it could be
caused by low water pressure.
• With the water filter removed, dispense 1 cup of water.
If 1 cup of water is dispensed in 8 seconds or less, the
water pressure to the refrigerator meets the minimum
requirement.
• If it takes longer than 8 seconds to dispense 1 cup of
water, the water pressure to the refrigerator is lower
than recommended. See "Water Supply Requirements"
or "Troubleshooting" for suggestions.
To Dispense Water (Standard):
NOTE: While dispensing water and for 3 seconds after
dispensing has stopped, the digital display will show how much
water has been dispensed. The default unit is ounces. To switch
to cups or liters, press the SETTINGS button, then press
MEASURED FILL to toggle through the available units.
Option 1:
1. Place a sturdy glass below the dispenser opening.
2. To dispense water, press the DISPENSE WATER button.
3. To stop dispensing, press the DISPENSE WATER button a
second time.
Option 2:
1. Press the WATER/ICE button until "Water" is selected.
2.
Press WATER/ICE to manually turn off the Measured Fill
feature.
NOTE: The dispenser will automatically turn off Measured
Fill after 1 minute of inactivity. When Measured Fill is turned
off, any changes you have made will be lost and all defaults
will be restored.
You can dispense water by the ounce, cup, or liter. The
default unit is ounces. To switch to cups or liters while the
Measured Fill feature is already on, press the MEASURED
FILL button to toggle through the available units.
Default, minimum, and maximum volumes are listed below.
Units Default Minimum Maximum
Ounces 8 1 128
Cups 1 1/4 16
Liters 0.25 0.05 4.00
3.
4.
Press the SETTINGS and TEMPERATURE buttons to adjust
the volume as desired. The SETTINGS button increases the
volume, and the TEMPERATURE button lowers the volume.
NOTE: Most coffee cups (commonly 4 to 6 oz [118 to
177 mL] per cup) are not the same size as a measuring cup
(8 oz [237 mL]). You may need to adjust the volume to avoid
unintentionally overfilling coffee cups.
You can save one "favorite" volume for repeated use. Adjust
the settings until the desired volume is displayed, then press
LOCI< to save the volume. In future Measured Fill use, press
LOCI< to access the saved volume setting.
NOTE: You can only save one "favorite." Saving a new
volume will overwrite the previously-saved "favorite."