Advertisement
CAUTION:
BesureyourgrillisOFFandcoolbefore cleaning.
Takecarenottochiporscratch thepainted surfaces.
Aswithallappliances, proper c areandmaintenance
willkeepyourgrillintopoperating c ondition a nd
prolong itslife.Byfollowing t hesecleaning p rocedures
ona timelybasis, y ourgrillwillstayclean andwork
propedywith minimum effort.
CleaningTheCookingGrids
Before initialuse.a, nci p erio,dically wesuggest yo.u wash
your
L,OOKmgL_nas In a mlla soap ana warm water
sotu,tion. You £an ,use a..wash cloth or vegetable brush
to clean your L,OOKIngL_rtas.
Cleaning The Flame Tamers
Periodically you sh.ould wa,sh the Flame Tam ,ers,in a
soap aria warm water solution, use a vege[aole orusn
to remove stubborn burnt-on cooking residue. Dry the
Flame/amers
thoroughly oeTore you reinstall them into
the cooking bowl.
Cleaning
The Grease Tray and Receptacle
To reduce the chance pf fire, t,h,eGrease praining,Tray
ana orease Kecep[ac_e snou_a De wsuaHy mspectea
before each grill use. Remove any grease aria wash
Grease Tray and Receptacle with a mild soap and
warm water solution.
Cleaning
the Inside of the Grill Lid
Gre,ase c,a,nhave a ten,d,encyto ,bui!d u,pon the ins,ide
of me L_riHLia ana coupe arip onto aecK or pmio wnen
the !idis open ,ed. V, i suall_inspect
the insiae of th,e Gri!l
Lla before
eacn grill
use.
Kemove any grease ana wasn
with a mild soap and warm water solution.
Annual Cleaning
of The Grill Interior
Burning-off the grill after every cookout will keep it
ready for instant use. However, once a year you should
give the entire grill a thorough cleaning to keep it in top
operating condition. Follow these steps:
1. Turn all Burner Valves to the full OFF position.
2. Turn the LP gas tank valve to the full OFF position.
3. Disconnect the regulator from the gas tank. Inspect
the hose with regulator assembly for cracking, cuts
or any other damage, and replace as neccessary
with Sears replacement parts. See Parts List.
Remove and clean the Flame Tamers, Cooking
4. Grids, Cooking Rack and Grill Burners.
.
6.
7.
Cover each Gas Valve Orificewith aluminum foil.
Brush the inside and bottom of the grill with a fiber
pad or nylon brush, and wash with a mild soap and
warm water solution. Rinse thoroughly and let dry.
Remove aluminum foil from Oriflcesand check
each Orifice for obstruction.
8. Check each Spark Electrode, adjusting as needed.
The space between the Spark Electrode Tip and
Spark Receiver should be approximately 3/16".
9. Replace the Burners and adjust the Gas Collector
Box. The edge of the collector box should be
overlapping the Bumer Port.
10. Replace Flame Tamers and the Cooking Grids.
11. Reconnect the gas source and observe the Burner
flame for correct operation.
Cleaning Exterior Surfaces:
Before initial use, and periodically thereafter, we
suggest you wash your grill using a mild soap and
warm water solution. You can use a wash cloth or
sponge for this process. Do not use a stiff wire or
brass brush that might remove paint during the clean-
ing process.
Cleaning Exterior Stainless Steel Surfaces:
Weathering and extreme heat can cause exterior
stainless steel surfaces to turn tan in color. Machine
oils used in the manufacturing process of stainless
steel can also cause this tanning color. After removing
the protective PVC film from the Grill Lid and Control
Panel use a Stainless Steel Cleaner to polish the
stainless steel surfaces of your grill. Never use abra-
sive cleaners or scrubbers because they will scratch
and damage your grill. Follow these steps for the best
results.
1. Turn the LP gas tank valve (clockwise) to the full OF F
position. Disconnect the regulator and hose assem-
bly from LP gas tank. Cover exposed gas fitting with
aluminum foil
2. Remove dirt.or grease using a soft cloth and polish
stainless surfaces. Wipe wi'th a soft cloth.
3. Remove aluminum foil from exposed gasfitting and
allow grill to air dry before attaching the regulator
and hose to yourLP gas tank.
Keep outdoor cooking gas appliance area clear and free
from combustible
materials, gasoline and other flam-
mable vaporsand liquids.
CAUTION:
1. Do not obstruct the flowof air for combustion
and ventilation.
2. Keep the ventilation openings of the cylinder
enclosure cabinet free and clear of debris.
3. Visually check burner flames occasionally to
observe for proper flame pattern as shown below.
BURNERFLAME
MAGNIFIED VIEW
THROUGH
LIGHTING HOLE
26
Advertisement
