Advertisement
_
Manually Lighting Your Grill by Match
To light your gas grill by match, insert a match into the
Lighting Stick and follow steps 1 through 6 of the
Basic Lighting Procedures. Then, light the match and
place Lighting Stick through the Lighting Hole on the
left side of the grill as shown below. Turn the nearest
Control Knob to the HIGH setting to release gas. The
Burner should light immediately.
LIGHTING
HOLE
LIGHTING
STICK
MATCH
Z WARNING
Never lean over the grill cooking area while
lighting your gas grill. Keep your face and
body a safe distance (at least 18 inches)
from the Lighting Hole or Burners, when
lighting your grill by match.
If the grill fails to light :
1. Turn gas off at source and turn the Control Knob to
OFF. Wait at least five minutes for gas to clear,
then retry.
2. If your grill still fails to light, check gas supply
and connections.
3. Repeat lighting procedure. If your grill still fails
to operate, turn the gas off at source, turn the
Control Knobs to OFF, then check the following:
• Misalignment of Burner Tubes over Orifices
Correction:
Reposition BumerTubes overOri-
rices.
• Obstruction in gas line
Correction: Remove fuet line from grill. Donot
smoke! Open gas supply for one second to clear
any obstruction from fuel line. Close off gas supply
at source and reconnect fuel line to grill.
• PluggedOrifice
Correction:
Remove Burnersfrom grill by pulling
Cotter Pin (beneath Burner) using Long nose
pliers. Carefully lift each Burner up and away
from gasvalve Orifice. Remove theOriflcefrom
gas valve and gently clear any obstruction with a
fine wire. Then reinstall all Orifices, Burners,
Cotter Pins and cooking components.
If an obstruction is suspected in Gas Valves or
Manifold, call the Grill Information Center at 1-
888-317-7642.
• Obstruction in Burner Tubes
Correction: Fotlowthe Burner Tube cleaning
procedure on page 27 of this Owner's Manual.
• Misalignment of Ignitoron Burner
Correction: Check for proper position of the
Electrode Tip as shown in step 18. The gap
between the Spark Electrode Tip and Spark
Receiver
should be approximately
3/16". Adjust
if necessary. With the gas supply closed and all
Control Knobs set to OFF press the Electric
Ignitor cap and check for the presence of a
spark at the Electrode.
• Disconnected Electric Wires
Correction:
Inspectthe Ignitor Junction Box
found behind the Control Panel. Connect loose
Electric wires to Junction Box and try to light the
grill.
•
Weak AA battery
Correction:
Unscrew the Ignitor Cap and replace
the battery.
4.
If the grill still does not light you may need
to purge air from the gas line or reset the
regulator excess gas flow device.
Note: This
procedure should be done every time a new
LP gas tank is connected
to your grill.
5.
To purge air from your gas line and/or
reset the regulator
excess gas flow device:
• Turn Control Knobs to the OFF position.
• Turn off the gas at the tank valve.
• Disconnect
regulator from LP gas tank.
• Let unit stand for 5 minutes to allow air to
purge.
• Reconnect regulator
to the LP gas tank.
• Turn the tank valve on slowly until 1/4 to
1/2 open.
• Open the Grill Lid.
• Push and turn the LEFT Control Knob to
HIGH.
• Press Electric
Ignitor for 3-4 seconds to
light the burners.
If all checks or corrections have been made and
you still have questions about operating your gas
grill, call the Grill Information
Center
8am - 8pm CST, Monday through
Friday at
1-888-317-7642.
Z WARNING
Should a FLASHBACK fire occur in/or
around the Burner Tubes, follow
the
instructions
below. Failure to comply with
these instructions
could result in a fire or
explosion that could cause serious bodily
injury, death, or property damage.
• Shut off gas supply to the gas grill.
• Turn the Control
Knobs to OFF position.
• Open the Grill Lid.
• Put out any flame with a Class B fire
extinguisher.
• Once the grill has cooled down, clean the
Burner Tubes and Burners according to
the cleaning
instructions
found on page 27
in this manual.
25
Advertisement
