KitchenAid KEBS278SSS - 27" Double Wall Oven Technical Manual page 79

Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
FAILURE ERROR
(Leftmost (Rightmost
2 Clock 2 Clock
SUGGESTED CORRECTIVE ACTION PROCEDURE
Digits) Digits)
KEYPAD DISCONNECTED
E0
F2
Keypad E1 STUCK OR SHORTED KEY
PROCEDURE: Before proceeding, press OFF, OFF, START to enter
the Diagnostic mode and verify the error codes.
A. Unplug oven or disconnect power.
B. Check keypad connector for firm connection.
C. Replace all parts and panels before operating.
D. Plug in range or reconnect power.
E. If error code returns after 60 seconds proceed to step F.
F. Unplug oven or disconnect power.
G. Replace keypad.
H. Replace all parts and panels before operating.
I. Plug in oven or reconnect power. Wait 60 seconds.
J. If error code returns after 60 seconds, proceed to step K.
K. Unplug oven or disconnect power.
L. Replace cable connecting user interface and keypad.
M. Replace all parts and panels before operating.
N. Plug in oven or reconnect power. Wait 60 seconds.
O. If error code returns after 60 seconds, proceed to step P.
P. Unplug oven or disconnect power.
Q. Replace oven user interface.
R. Replace all parts and panels before operating.
S. Plug in oven or reconnect power. Wait 60 seconds.
T. Verify operation is normal. Press OFF, OFF, START to reenter the Diagnostic
mode and complete checks.
UPPER OVEN SENSOR SHORTED OR OPEN
E0
F3
E1 LOWER OVEN SENSOR SHORTED OR OPEN
Sensors
E3
MEAT PROBE SHORTED
PROCEDURE: Before proceeding, press OFF, OFF, START to enter
the Diagnostic mode and verify the error codes.
A. Verify in Diagnostics temperature reading on sensor.
B. If dashes appear in main temperature display proceed to step C.
C. Unplug oven or disconnect power.
D. Remove back panels and ensure the indicated temperature sensor is plugged
in properly and fully inserted. If not, plug in the connector and proceed to step J.
If sensor is plugged in properly proceed to step E.
E. Check connector P2 on the appliance manager. Ensure P2 connector is plugged
in properly and fully inserted. If connector is inserted properly go to step J.
If not proceed to step F.
F. Visually inspect the wires between P2 on the appliance manager and the
indicated temperature sensor. Make sure the wires are not pinched or cut.
If wires appear intact, unplug P2 connector on the appliance manager.
Go to step G.
G. Measure the indicated sensor resistance value (measure between appropriate
P2 connector pins). For the following sensors, the resistance value should read:
Upper Oven Sensor Between 931 and 2869 Ω .
(Approx. 1080 Ω at room temp.)
Lower Oven Sensor Between 931 and 2869 Ω .
(Approx. 1080 Ω at room temp.)
Meat Probe Sensor Between 1,300 and 103,000 Ω .
Electrical Shock Hazard
MESSAGE/DESCRIPTION
WARNING
FAILURE ERROR
(Leftmost (Rightmost
2 Clock 2 Clock
SUGGESTED CORRECTIVE ACTION PROCEDURE
Digits) Digits)
H. For UPPER and LOWER sensors:
Replace appropriate temperature sensor. Repeat step G.
If the requirements are not met, replace sensor harness. Repeat step G.
For MEAT PROBE SENSOR:
Replace meat probe sensor, repeat step G.
If the requirements are not met, replace sensor harness. Repeat step G.
If the requirements are still not met, replace the meat probe jack.
Repeat step G.
If the meat probe sensor is still not operating correctly go to step I.
I. Replace the appliance manager. Ensure all connectors are properly placed and
firmly connected.
J. Replace all parts and panels before operating.
K. Plug in oven or reconnect power. Wait 60 seconds.
L. Enter into Diagnostic mode and read sensor for upper oven sensor and meat
probe on immediate display.
F3
E2
WARMING DRAWER SENSOR SHORTED OR OPEN
Sensors
PROCEDURE: Oven is not equipped with this feature. If error occurs press OFF,
OFF, START to enter into Diagnostic mode and verify the error codes. If error code
returns, replace user interface with correct control associated with this product.
DOOR AND LATCH SWITCH DO NOT AGREE
E0
F5
E1 DOOR LATCH NOT OPERATING.
PROCEDURE: Before proceeding, press OFF, OFF, START to enter
the Diagnostic mode and verify the error codes.
TO VERIFY DOOR SWITCH:
A. While in diagnostics, open the oven door. The second digit on the clock display
should toggle between "1" and "0" as the door opens and closes. When door is
closed display should show "1", when the door is open display should show "0".
If the second digit on the clock display did not toggle, go to step B.
If the digit did not toggle after replacing the door switch, go to step D.
If the digit did not toggle after replacing the door switch harness, go to step F.
B. Unplug oven or disconnect power.
C. Replace door switch. (If door switch is integral to the door latch motor
assembly, replace the entire door/latch motor assembly). Go to step H.
D. Unplug oven or disconnect power.
E. Check the integrity of the harness wires and connections between the
appliance manager and the door/latch assembly. Ensure there are no shorted
or pinched wires.
If the wiring harness is pinched or damaged, replace the door switch harness.
Go to step H.
If wiring harness is good, go to step H.
F. Unplug oven or disconnect power.
G. Replace appliance manager. Go to step H.
H. Replace all parts and panels before operating.
I. Plug in oven or reconnect power.
J. Press OFF, OFF, START to reenter the Diagnostic mode and complete checks.
Repeat step A.
6-3
MESSAGE/DESCRIPTION