Related Manuals for Sears Vacuum Cleaner
Summary of Contents for Sears Vacuum Cleaner
- Page 1 Vacuum Cleaner OWNER'S MANUAL READ THIS MANUAL for important safety, assembly and operating instructions.
- Page 2 AND OPTIONAL WARRANTY ..............SERVICE..............FEATURES IMPORTANT SAFETYINSTRUCTIONS ......PARTSAND FEATURES..........ASSEMBLY..............Users of upright vacuum cleaners have a variety!of cleaning needs. How to Staff ............This vacuum cleaner comes with optior ._atures Pile Height Selection and Setting ....... which offer the customer the opportuni _select Bare Floor Setting (Optional)
- Page 3 Use your cleaner only as described in this free of dust, lint, hair and anything _hat manual. Use only with Sears recommended may reduce air flow. attachments. Keep hair, loose clothing, fingers, and all To reduce the risk of electrical...
- Page 4 AND FEATURES It is important to know your vacuum cleaner parts UPRIGHTVACUUM CLEANER and features to assure its proper and safe use, Review these before using your cleaner. COPY YOUR MODEL AND SERIAL NUMBERSHERE. Handle Copy this information from the bottom of the vacuum cleaner into these spaces.
- Page 5 HANDLE ASSEMBLY (STANDARD MODEL) Before assembling your vacuum cleaner be sure you Carry Handle have all the parts shown. Screw Electrical Shock Hazard Do not plug into the electrical supply untll the assembly is complete. Failure to do so could result in electrical shock or injury.
- Page 6 Using a screwdriver. tighten the screw, W TOSTART (STANDARD MODEL) Unwrap the power cord. Plug the power cord into a 120 volt outlet located near the floor. (OPTIONAL MODEL) 1. Turn the quick release cord hook CAUTION to either side and Release down to release the power cord.
- Page 7 HEIGHT FLOOR SELECTION AND SETTING SETTING (OPTIONAL MODEL) To select the bare floor seffing: To select a pile height setting: Turn off the cleaner. Turn off the cleaner. Select a pile height setting by tilting the cleaner back until the front wheels are Tilt the cleaner back until the front wheels are lifteid lifted slightly off the floor.
- Page 8 AND POWER LEVELSELECTION HANDLEON/OFF SWITCH TWO SPEEDS (STANDARDMODEL) (OPTIONAL MODEL) To start the To staff the vacuum vacuum cleaner, cleaner, slide the slide the On/Off Two-Speed On/Off Switch from the Switch to the LO or HI OFF position to the position.
- Page 9 The attached hose end To achieve maximum swivels 360 degrees to reach (approximately feet) with the attachments, make cleaning add the crevice tool to the easier in every direction. end of the wand by inserting and twisting Remove the telescoping slightly.
- Page 10 To Store Attachments: EXTENSION HOSE NOT INCLUDED IN ALL MODELS Remove dusting brush or upholstery tool. Snap into appropriate storage location. The stretch hose attached to the vacuum cleanler has two "J" shaped slots in the end where attach- Remove crevice tool from the wand by twisting. ments fit into.
- Page 11 CAUTION PersonalInjuryHazard Whenusingthe regularhose or withthe extension Usecare if vacuum cleaner isplaced on stairs.If it hose attached, the cleaner shouldbe on a solid falls,personal injuryor property damage could surface, such as the floor,on the same level or below result.
- Page 12 PERFORMANCE INDICATOR (OPTIONAL MODEL) Performance When the unit is running with normal air flow, the lines Indicator on the Performance indicator are white. Red lines (Optional) appear in the performance indicator whenever airflow becomes blocked. If that occurs, check the disposable dust bag, motor safety filter and other possible clog locations shown on page 18.
- Page 13 CHANGING To Remove Bag: To Replace Bag: ..Fold the safety seal tab on the new dust bqg (#20-50688) away from the opening that fits on the dirt tube. Release Button Dust Bag Seal Tab Press the Release Button Bag -- located on the top of the bag cover.
- Page 14 TORSAFETY FILTER CLEANING Check motor safety filter occasionally and clean when dirty. Filter Check th_ filter WARNING located below the foam Ifilter. If it is dirty, Electrical ShockHazard Motor wipe it width a Do not operate the cleaner withoutthe motor safety clean, dry fi#er.
- Page 15 Unfold the new dust Position the bag cover so its positioning tab bag. fits into the body Insert the dust bag onto positioning tab slot. the bag holder completely by holding the bag collar. BagCover ---J Positioning Snap the dust bag collar into position.
- Page 16 T CHANGINGAND BRUSHCLEANING Lift the base Belt plate to Electrical Shock Or Personal Injury Hazard uncover the Disconnect electrical supply before servicing or brush assembly cleaning the unit. Failure to do so could result in and belt. electrical shock or personal injury from cleaner suddenly starting.
- Page 17 To replace belt: CAUTION Loop the end of the new belt (#20-5286) on the brush assembly. Remove any dirt or debris in the belt path area or in the brush roller area. Motor Drive _haft Exploded View - BrushAssembly End Cap Belt Groove Carefully...
- Page 18 To re-attach the base plate, insert the four tabs into the four slots along the front edge of the base. Lower the base plate to its original position. Latch Right Latch Tab Locations Slide latches toward the center of the unit to s_cure. Base Plate Tab Reposition...
- Page 19 REMOVAL Always follow all safety precautions when cleaning Close clean-out port cover firmly to insure seal. and servicing the vacuum cleaner. Re-insert the hose into the opening on the lower body from which it was removed. Press firml_yto assure connection. Electrical Shock Or Personal Injury Hazard Clean-Out Port Cover...
- Page 20 BULB CHANGING Lift the WARNING protective shield, To release the Electrical Shock Or Personal Injury Hazard light bulb, Disconnect electrical supply before servicing or carefully push cleaning the unit. Failure to do so could result in the bulb in and electrical shock or personal injury from cleaner turn to the left.
- Page 21 SERVICING Push out worn brushes and end brushes. Slide the new Electrical Shock Or Personal Injury Hazard brushes and end Disconnect electrical supply before servicing or brushes into the cleaning the unit. Failure to do so could result Jn slots. Make sure electrical shock or personal injury from cleaner not to reverse the suddenly starting.
- Page 22 TING Review this chaff to find do-it-yourself solutions for minor performance problems, WARNING Electrical Shock or Personal Injury Hazard Disconnect electrical supply before servicing or cleaning the unit. Failure to do so could result in electrical shock or personal injury from cleaner suddenly starting. PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION...
- Page 23 SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, I L 60195 U.S.A. PARTNO. C_ 1ZYU3_U_-4368722E Printed in U.S.A.