Useful Features; Sound Adjustments; Sound Mode Settings; Sound Via - Sharp Aquos LC-20B6E Operation Manual

Useful Features

Sound Adjustments

Adjust the sound quality and volume to suit your preference.
See the table below for the adjustment items.
1
Press MENU to display the Menu screen.
• The Sound Menu screen can be displayed directly by
pressing the Green button.
2
Press \/| to select "Sound".
3
Press '/" to select a specific adjustment item.
M e n u [ S o u n d ]
Picture Sound Setup Features
S o u n d v i a
T r e b l e
B a s s
H e a d p h . v o l . [
L o u d s p . s o u n d
H e a d p h . s o u n d
A V a u d i o
B a l a n c e
A d v a n c e d
R e s e t
4
Press \/| to adjust the item to your desired position.
5
Press END to exit.
\ \ \ \ \ button
Selected item

Treble*

For weaker treble

Bass*

For weaker bass

Headph. vol.*

Decrease headphones
volume

Balance*

Increase the volume of
the left speaker
* These items cannot be adjusted when "Sound via" is set to "Hi-fi".
NOTE
• Select "Advanced" and press OK to set "Speech emphasis",
"Sound wide" or "PC sound select". See page 18.
• When resetting all adjustment items (except for "Loudsp. sound",
"Headph. sound", "AV audio sig." and the items on the "Advanced"
menu) to factory preset values, perform the following procedures.
1 Press '/" to select "Reset", and press OK.
2 Press '/" to select "Yes", and press OK.
[ T V ]
[ 0 ] - +
[ 0 ] - +
3 0 ]
s i g .
[ 0 ] - +
| | | | | button
For stronger treble
For stronger bass
Increase headphones
volume
Increase the volume of
the right speaker

Sound Mode Settings

You can make various sound mode settings.
1
Perform steps 1 and 2 in Sound Adjustments to
display the Sound Menu screen.
2
Press '/" to select the desired item, and press OK.
M e n u [ S o u n d ]
Picture Sound Setup Features
S o u n d v i a
T r e b l e
B a s s
H e a d p h . v o l . [
L o u d s p . s o u n d
H e a d p h . s o u n d
A V a u d i o
B a l a n c e
A d v a n c e d
R e s e t
3
Press '/" to select the sound mode, and press OK.
4
Press END to exit.
Selected item

Sound via

TV Hi-fi
Stereo Mono

Loudsp. sound*

Sound1

Headph. sound*

Nicam Mono, Mono
Sound1

AV audio sig.*

* These items are available only when the TV or FM radio mode is
selected as an input mode.
NOTE
For the "Sound via" setting
• When setting "Sound via" to "Hi-fi" in the Sound Menu screen, the
sound from the built-in speakers will be turned off. To exit this
mode, switch "Sound via" from "Hi-fi" to "TV" in the Sound Menu
screen.
• Pressing i (–)/(+) will display the volume indicator shown
below. You can adjust the volume by pressing i (–)/(+).
Hi-fi Volume
20
For the "Loudsp. sound" and "Headph. sound" settings
• "Headph. sound" cannot be set when "Sound via" is set to "Hi-fi".
• The sound output modes differ depending on whether or not a
NICAM or A2 stereo signal is received. See page 32.
For the "AV audio sig." setting
• Select "Sound1" or "Sound2" when playing back the video from
mono-video recorders and "Sound1+2" when playing back that
from stereo-video recorders.
[ T V ]
[ 0 ] -
[ 0 ] -
3 0 ]
s i g .
[ 0 ] -
Choice
Sound2 Sound1+2 Mono
Sound2 Sound1+2
+
+
+
17