Backlight And Power Setting; Wide Mode; Wide Mode; Backlight - Sharp Aquos LC-20B6E Operation Manual

Useful Features (Continued)

Backlight and Power Setting

You can make settings for the brightness of the screen and
for shutdown of the power.
1
Press MENU to display the Menu screen.
2
Press \/| to select "Features".
3
Press '/" to select the desired item, and press OK.
M e n u [ F e a t u r e s ]
Picture Sound Setup
4
Press '/" to make the setting.
: SELECT O K : ENTER
5
Press END to exit.
Selected item Factory setting

Backlight*

1 [Bright] Maximum
brightness
Auto power [Off] This feature
off (only for is inactive.
TV mode)
Power [Off] No power
management* 2 management.
(only for PC
mode)
* 1 The Backlight setting can be switched with one touch using the remote
control (see below).
2
* For details on this setting, see page 37.
■
Directly setting the Backlight
You can change the setting of Backlight directly.
Press BACKLIGHT to select the desired mode.
• Each time you press BACKLIGHT, the mode changes as follows.
B a c k l i g h t : B r i g h t
B a c k l i g h t : A u t o ( O P C )
NOTE
• The Backlight screen automatically disappears after 4 seconds.
• See the table above for details of the each brightness setting.
• When set to "Auto (OPC)", make sure that no object obstructs the
OPC sensor, which could affect its ability to sense surrounding light.
28
Features
W i d e m o d e
B a c k l i g h t
T i m e r f u n c t i o n s
A u t o p o w e r o f f
O n - s c r e e n d i s p .
C h i l d l o c k
P o w e r m a n a g e m e n t
M : BACK E : EXIT
Choice
[Medium] Brightness 60% → Suitable
for viewing in well-lit areas.
Saves energy.
[Dark] Brightness 20% → Sufficiently
bright when viewing in dim areas.
[Auto (OPC)] Screen brightness is
adjusted according to the
ambient light of the room.
[On] The power of the LCD TV set is
turned off when there is no
signal for 5 minutes.
[On] If no signal inputs for 8 minutes,
the power shuts down.
B a c k l i g h t : M e d i u m
B a c k l i g h t : D a r k

Wide Mode

You can select the picture display size for the playback
image of the DVD player from the following four modes:
"4:3", "16:9", "Zoom" and "Stretch".
NOTE
• "Wide mode" setting is not available only when 1080I and 720P
signals are entered through the COMPONENT input terminals.
• "Wide mode" cannot be set when the PC or FM radio mode is
selected as an input mode.
1
Perform steps 1 and 2 in Backlight and Power Setting
to display the Features Menu screen.
2
Press '/" to select "Wide mode", and press OK.
M e n u [ F e a t u r e s : W i d e
Picture Sound Setup Features
W i d e
B a c k l i g h t
T i m e r
A u t o
O n - s c r e e n
C h i l d
P o w e r
3
Press '/" to select the desired mode, and press OK.
M e n u [ F e a t u r e s : W i d e M e n u [ F e a t u r e s : W i d e : SELECT O K : ENTER
S e l e c t o p t i o n
4 : 3
1 6 : 9
Z o o m
S t r e t c h
4
Press END to exit.
Selected item
4:3 Displays the image in a 4:3 aspect ratio.
16:9 Stretches the image horizontally to display it in a
16:9 aspect ratio.
Zoom Displays the centre part of the image by enlarg-
ing it in the horizontal and vertical directions.
Stretch Stretches the image horizontally.
Image type 4:3
(For an image
stretched
vertically)
(For an image
stretched
vertically with
bands at the left
and right sides)
(For a 4:3 image)
NOTE
• The 4:3 image will be deformed on the screen when the "Wide mode"
is set to "16:9".
m o d e ]
m o d e
f u n c t i o n s
p o w e r o f f
d i s p .
l o c k
m a n a g e m e n t
M : BACK m o d e ] m o d e ] E : EXIT
Description
16:9 Zoom Stretch