Related Manuals for Packard Bell EasyNote T5 SEries
Summary of Contents for Packard Bell EasyNote T5 SEries
- Page 1 EasyNote T5 series Disassembly Manual NEC Computers International B.V. EasyNote T5 series Disassembly Manual Revision: 2.1 Date: March 2005 For Packard Bell A division of NEC Computers International B.V.
-
Page 2: Table Of Contents
Removing the LCD Module ............................12 Removing the LCD Penal............................14 Removing the Top Cover ............................16 Removing the Touch Pad............................18 Removing the DC/DC Board ............................19 Removing the Main Board............................20 DIP Switch Setting ..............................22 Screws ..................................23 Notice...................................24 Packard Bell EasyNote T5 Disassembly Manual Page 2... -
Page 3: Overview
Furthermore, the screws that are removed are shown next to the image of the parts themselves. Packard Bell reserves the right to make changes to the EasyNote T5 chassis without notice. Technician Notes Only technicians authorized by NEC Computers International B.V. -
Page 4: Hazardous Voltage
Inside the power supply are hazardous avviare il sistema senza aver prima messo a voltages that can cause serious personal injury. Always posto il coperchio return a defective power supply to your dealer. Packard Bell EasyNote T5 Disassembly Manual Page 4... -
Page 5: Removing The Battery
1. Remove the screws as shown in Fig. 2 M2.5x11 Black Fig. 2 Removing the Hard disk drive cover 2. Lift up the hard disk drive and disconnect it as shown in Fig. 3 Packard Bell EasyNote T5 Disassembly Manual Page 5... -
Page 6: Removing The Mdc Modem Module
M2.5x3.5 Sliver Fig. 5 Removing the screws on the MCD modem 2. Carefully lift up MDC modem module. 3. Disconnect the cable attached to the MDC modem and put the modem aside. Packard Bell EasyNote T5 Disassembly Manual Page 6... -
Page 7: Removing The Keyboard Cover
2. Remove the Keyboard Cover as shown in Fig. 7 Fig. 7 Removing the Keyboard Cover Removing the Keyboard To remove the Keyboard module, first remove the keyboard cover (see Removing keyboard cover), then perform the following steps: Packard Bell EasyNote T5 Disassembly Manual Page 7... -
Page 8: Removing The Optical Drive & Heat Plate
To remove the optical drive & heat plate, first remove the keyboard cover (see Removing the keyboard cover), remove the keyboard (see Removing the keyboard) then perform the following steps: 1. Remove the screw as shown in Fig. 10 Packard Bell EasyNote T5 Disassembly Manual Page 8... - Page 9 2. Push the Optical Drive module out from the base unit as shown in Fig. 11 Fig. 11 Pushing Optical Drive module out from base unit 3. Carefully remove the heat plate from the base unit. Packard Bell EasyNote T5 Disassembly Manual Page 9...
-
Page 10: Removing The Memory Module
2. Remove the Memory Module from its slot and put it aside. Removing the Wireless Module To remove the Wireless Module, first remove the keyboard cover (see Removing the keyboard cover), remove the keyboard (see Removing the keyboard), remove the heat plate (see Packard Bell EasyNote T5 Disassembly Manual Page 10... -
Page 11: Removing Heat Sink & Cpu
(1à2à3à4). This is to ensure a well distributed pressure over the CPU and to prevent damaging the CPU 2. Carefully remove the heat sink from the CPU socket as shown in Fig. 16 Packard Bell EasyNote T5 Disassembly Manual Page 11... -
Page 12: Removing The Lcd Module
To remove the LCD Module, first remove the Keyboard Cover (see Removing the keyboard cover) then remove the keyboard (see Removing the keyboard) and disconnect the wireless antenna cables (see Removing the Wireless Module). Packard Bell EasyNote T5 Disassembly Manual Page 12... - Page 13 Fig. 19 Removing the LCD cable Cover 3. Release the screws at rear side of the unit as shown in Fig. 20 M2x6 Black Fig. 20 LCD hinge screws at the rear Packard Bell EasyNote T5 Disassembly Manual Page 13...
-
Page 14: Removing The Lcd Panel
Removing the LCD Panel To remove the LCD Panel, first remove the LCD Module (see Removing the LCD Module), then perform the following steps: 1. Unscrew all screws shown in Fig. 22 Packard Bell EasyNote T5 Disassembly Manual Page 14... - Page 15 Relase the LCD Bezel carefully and put it aside as shown in Fig. 23 Fig. 23 Removing the LCD Bezel 3. Unscrew all screws encircled in Fig. 24 disconnect the inverter board and put it aside. Packard Bell EasyNote T5 Disassembly Manual Page 15...
-
Page 16: Removing The Top Cover
5. Remove the screws at both sides of the LCD panel in order to release the LCD hinges as shown in Fig. 25 . Fig. 25 Removing the LCD Panel hinges Removing the Top Cover Packard Bell EasyNote T5 Disassembly Manual Page 16... - Page 17 B = M2.5x11 Black Fig. 27 Removing the Top cover screws on the bottom of the system M2x3 Sliver 4. Remove all screws in the battery compartment as shown in Fig. 28 Packard Bell EasyNote T5 Disassembly Manual Page 17...
-
Page 18: Removing The Touch Pad
Removing the Touch Pad To remove the Touch Pad, first remove the Top Cover (see Removing the Top Cover), then perform the following steps: Packard Bell EasyNote T5 Disassembly Manual Page 18... -
Page 19: Removing The Dc/Dc Board
To remove the DC/DC board, first remove the Top Cover (see Removing the Top Cover), then perform the following steps: 1. Remove the screw on the DC/DC board as shown in Fig. 31 Packard Bell EasyNote T5 Disassembly Manual Page 19... -
Page 20: Removing The Main Board
To remove the Main board, first open the Top Cover (see Removing the Top Cover), remove DC/DC board (see Removing DC/DC board) then perform the following steps: 1. Remove the screws holding the main board in place as shown in Fig. 33 Packard Bell EasyNote T5 Disassembly Manual Page 20... - Page 21 2. Disconnect the VGA connector from the base as shown in Fig. 34 Fig. 34 Disconnecting the VGA connector 3. Lift the main board out of the system and put it aside (Fig. 35 ). Packard Bell EasyNote T5 Disassembly Manual Page 21...
-
Page 22: Dip Switch Setting
ON : connect to GND OFF : NC Bit6 Password Password override. ON: Override OFF: Available (factory setting) Bit 1 Bit 2 Keyboard code OFF US Keyboard OFF JP Keyboard Reserved UK Keyboard Packard Bell EasyNote T5 Disassembly Manual Page 22... -
Page 23: Screws
Screws M2.5x5.6 Silver M2.5x3.5 Silver M2.5x8 Sliver M2.5x10 Silver M2.5x11 Black M2.5x12.5 Silver M2.5x15 Black M2x3 Sliver M2x6 Black M3x4 Black M2.5x5 Sliver Packard Bell EasyNote T5 Disassembly Manual Page 23... -
Page 24: Notice
Allen Koay (S&S Penang) NEC Computers Malaysia* September 2003 Dean Egberts (S&S Wijchen) Packard Bell Europe* March 2005 Dean Egberts (S&S) Packard Bell Europe* * A division of NEC Computers International B.V. Packard Bell EasyNote T5 Disassembly Manual Page 24...