Important Information - DSC PowerSeries PC1616 User Manual

FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Dig-
ital Security Controls could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accord-
ance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful in-
terference to radio or television reception, which can be deter-mined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Re-orient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful:
"How to Identify and Resolve Radio/Television Interference Problems".
This booklet is available from the U.S. Government Printing Office,
Washington D.C. 20402, Stock # 004-000-00345-4.
The keypads represented in this manual can be used with the following
Control Units: PC1616, PC1832, PC1864.

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC Rules and, if the prod-
uct was approved July 23, 2001 or later, the requirements adopted by the
ACTA. On the side of this equipment is a label that contains, among other
information, a product identifier. If requested, this number must be pro-
vided to the Telephone Company.
PC1616 Product Identifier
PC1832 Product Identifier
PC1864 Product Identifier
USOC Jack: RJ-31X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring
and telephone network must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A compliant telephone
cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. See instal-
lation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be con-
nected to a telephone line. Excessive RENs on a telephone line may result
in the devices not ringing in response to an incoming call. In most but not
all areas, the sum of RENs should not exceed five (5.0). To be certain of
the number of devices that may be connected to a line, as determined by
the total RENs, contact the local Telephone Company. For products ap-
proved after July 23, 2001, the REN for this product is part of the product
identifier that has the format US: AAAEQ##TXXXX. The digits repre-
sented by ## are the REN without a decimal point (e.g., 03 is a REN of
0.3). For earlier products, the REN is separately shown on the label.
Incidence of Harm
If this equipment (PC1616, PC1832, PC1864) causes harm to the tele-
phone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance no-
tice is not practical, the Telephone Company will notify the customer as
soon as possible. Also, you will be advised of your right to file a com-
plaint with the FCC if you believe it is necessary.
INDUSTRY CANADA STATEMENT
NOTICE: This Equipment meets the applicable Industry Canada Terminal
Equipment Technical Specifications. This is confirmed by the registration
number. The abbreviation, IC, before the registration number signifies that
registration was performed based on a Declaration of Conformity indicat-
ing that Industry Canada technical specifications were met. It does not im-
ply that that Industry Canada approved the equipment
NOTICE: The Ringer Equivalence Number (REN) for this terminal equip-
ment is 0.1. The REN assigned to each terminal equipment provides an in-
dication of the maximum number of terminals allowed to be connected to
a telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Numbers of all devices does not exceed 5.
PC1864 Registration number
PC1832 Registration number
PC1616 Registration number
US: F53AL01BPC1614
US: F53AL01BPC1832
US: F53AL01BPC1864
IC: 160A-PC1864
IC: 160A-PC1832
IC: 160A-PC1614
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment.
If this happens the Telephone Company will provide advance notice in
order for you to make necessary modifications to maintain uninterrupted
service.
Equipment Maintenance Facility
If trouble is experienced with this equipment (PC1616, PC1832,
PC1864) for repair or warranty information, contact the facility indicated
below. If the equipment is causing harm to the telephone network, the
Telephone Company may request that you disconnect the equipment un-
til the problem is solved. This equipment is of a type that is not intended
to be repaired by the end user.
DSC c/o APL Logistics 757 Douglas Hill Rd, Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state
public utility commission, public service commission or corporation
commission for information.
Alarm dialing equipment must be able to seize the telephone line and
place a call in an emergency situation. It must be able to do this even if
other equipment (telephone, answering system, computer modem, etc.)
already has the telephone line in use. To do so, alarm dialing equipment
must be connected to a properly installed RJ-31X jack that is electrically
in series with and ahead of all other equipment attached to the same tele-
phone line. Proper installation is depicted in the figure below. If you have
any questions concerning these instructions, you should consult your tel-
ephone company or a qualified installer about installing the RJ-31X jack
and alarm dialing equipment for you.
Customer Premises Equipment and Wiring
Network
Service
Provider s
R -31
Facilities
ack
Alarm Dialing
Telephone
Line
Network
Demarcation
Telephone
Point
Answering
System
This product is in conformity with EMC Directive 2004/108/EC based on
results using harmonized standards in accordance with article 10(5),
R&TTE Directive 1999/5/EC based on following Annex III of the direc-
tive and LVD Directive 2006/95/EC based on results using harmonized
standards.
This product meets the requirements of Class II, Grade 2 equipment as per
EN 50131-1:2006 + A1:2009 Standard. This product is suitable for use in
systems with the following notification options:
- A (use of two warning devices and internal dialer required),
- B (self powered warning device and internal dialer required),
- D (use of alternate IP/GSM communicator with encryption enabled re-
quired).
EN50131-1 Grade 2 Class II
The Model PC1864, PC1832, PC1616 Control Panel has been certified by
Telefication according to EN50131-1:2006 + A1:2009, EN50131-3:2009,
EN50131-6:2008 and EN50136-1:1997 for Grade 2, Class II, ATS2.
Computer
Unused
R -11 ack
Equipment
Unused
Fax Machine
R -11 ack
Telephone
Telephone