Data Type - Fostex VR800 Owner's Manual

Data Type

< l o o p o p . m o d e > < l o o p o p . m o d e > < l o o p o p . m o d e >
< l o o p o p . m o d e > < l o o p o p . m o d e >
< p o s t l o c a t e m o d e > < p o s t l o c a t e m o d e > < p o s t l o c a t e m o d e > < p o s t l o c a t e m o d e > < p o s t l o c a t e m o d e >
< c o u n t > < c o u n t > < c o u n t >
< c o u n t > < c o u n t >
< m m c t r a c k > < m m c t r a c k > < m m c t r a c k > < m m c t r a c k > < m m c t r a c k >
< e d i t m e s s a g e > < e d i t m e s s a g e > < e d i t m e s s a g e > < e d i t m e s s a g e > < e d i t m e s s a g e >
< m m c t i m e > < m m c t i m e >
< m m c t i m e > < m m c t i m e > < m m c t i m e >
< o n / o f f > < o n / o f f > < o n / o f f > < o n / o f f > < o n / o f f >
< r e p e a t c o u n t > < r e p e a t c o u n t > < r e p e a t c o u n t > < r e p e a t c o u n t > < r e p e a t c o u n t >
< c h a n n e l > < c h a n n e l > < c h a n n e l > < c h a n n e l > < c h a n n e l >
< l o c k e n a b l e > < l o c k e n a b l e >
< l o c k e n a b l e > < l o c k e n a b l e > < l o c k e n a b l e >
< l o c k s t a t u s > < l o c k s t a t u s > < l o c k s t a t u s >
< l o c k s t a t u s > < l o c k s t a t u s >
< p r o g r a m > < p r o g r a m > < p r o g r a m > < p r o g r a m > < p r o g r a m >
< l o c k m o d e > < l o c k m o d e > < l o c k m o d e > < l o c k m o d e > < l o c k m o d e >
VR800 Owner's Manual (MIDI Implementation Chart/MMC List)
12=stop
Indicates the next operating mode following locating to the start point (GP3) upon arriving
at the end point (GP6) by the play mode. In VR800, 12=stop only is effective.
12=stop
15=play
Specifies operating mode in which VR800 should enter upon completing the locate
operation. Corresponds to the setting of AUTO PLAY ON ("15")/OFF ("12") on the main
unit.
01 ~ 7F
Specifies succeeding data byte numbers.
Complies to the MMC (MIDI Machine Control) standard track bit map.
In VR800, you always need to specify two byte combinations of "r0" and "r1."
00 = no message
01 = completed (completion flag)
02 = active (execution flag)
02<mmc time> = Indicates unprocessed time by active (execution flag) and <mmc time>.
02<count><mmc track> = Indicates source track by active (execution flag) and <mmc
track>. Used for clipboard play.
03 = cancel (execution stop)
05 = Indicates rehearsal (rehearsal mode of auto rec). Possible of undo.
06 = Indicates take (take mode of auto rec). Possible of undo.
10 = over value error
10 <mmc time> = Capacity shortage time is indicated by over value error (error by
capacity shortage) and <mmc time>. In copy paste, it indicates capacity shortage time
required for a minimum one time paste.
11 = Indicates in point error (incorrect in point).
12 = Indicates out point error (incorrect out point).
14 = Indicates void data (data necessary for paste does not exist).
18 = Indicates track select error (track necessary to execute copy/move or erase/cut is not
correctly setup).
19<repeat count> = Indicates repeat number error and repeat numbers executable by
<repeat count>.
1A = Indicates disable rec (record disable mode).
25 = Indicates can't undo rehearsal (rehearsal mode of auto rec). Impossible to undo.
26 = Indicates can't undo take (take mode of auto rec). Impossible toundo.
71 = Indicates on.
72 = Indicates off.
hr mn sc fr {ff/st} complies to the MMC standard time code.
70 = default
71 = on
72 = off
01 ~ 7F
Especially when executing commands such as paste, the number of pasting times to be
continuously repeated following the auto punch in point is specified.
00 ~ 08, 7F
Select recorder tracks 1~8. "00" in particular, is not specified (default setting). "7F"
indicates input/output of Adat optical. For details, refer to explanation on setting the
Command/Mode.
00 = lock disable, chase disable
01 = lock enable, chase enable
Corresponds to SLAVE ON ("01")/OFF ("00") in the main unit.
00 = lock disable, chase disable
01 = lock enable (unlocked), chase enable (unlocked)
11 = lock enable (locked), chase enable (locked)
01 ~ 7F
Indicates program numbers (P1 ~ P99) on the main unit. However, VR800 can specify
only 01 (corresponds to P01) ~ 63H (corresponds to P99).
40 = Free
42 = Vari
Indicates the slave mode when this equipment is set to slave ON.
111