Page 3: Table Of Contents
Safety Restraints Starting Your Ranger ....41 Warning Lights and Gauges ....53 Instrument Panel Controls .
Page 4: Introductory Information
Ford’s Commitment to You At Ford Motor Company, excellence is the continuous commitment to achieve the best result possible. It is dedication to learning what you want, determination to develop the right concept, and execution of that concept with care, precision, and attention to detail.
Page 5 This guide describes equipment and gives specifications for equipment that was in effect when this guide was approved for printing. Ford may discontinue models or change specifications or design without any notice and without incurring obligation. NOTES and WARNINGS NOTES give you additional information about the subject matter you are referencing.
Page 6 If you lose your Warranty Information Booklet, you can get a new one free of charge. Contact any Ford or Lincoln-Mercury dealer, or refer to the addresses and phone numbers on the first page of this owner guide.
Page 7 Buying a Ford Extended Service Plan If you bought your vehicle in the U.S., you can buy a Ford Extended Service Plan for your vehicle. This optional contract provides service protection for a longer period of time than the basic warranty that comes with your vehicle.
Page 8 500 miles/800 km after any wheel change or any other time the wheel lug nuts have been loosened. Use only the type of engine oil that Ford recommends. See Engine oil recommendations in the Index. Do not use special “break-in” oils.
Page 9: Cleaning The Outside Of Your Vehicle
Ford, however, believes that continual improvement in customer satisfaction is a high priority. For this reason, Ford has authorized its dealers to repair, at no charge to the owner,...
Page 10 Introductory Information Cleaning Plastic Parts Some of your vehicle’s exterior trim parts are plastic. Clean with a tar and road oil remover if necessary. Use a vinyl cleaner for routine cleaning. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners.
Page 11: Safety Restraints
Important Safety Belt Information The use of safety belts helps to restrain you and your passengers in case of a collision. In most states and in Canada the law requires their use. Safety belts provide best restraint when: the seatback is upright the occupant is sitting upright (not slouched) the lap belt is snug and low on the hips the shoulder belt is snug against the chest...
Page 12 Ford recommends that all safety belt assemblies and attaching hardware should be inspected by a qualified technician after any collision. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted.
Page 13: Combination Lap And Shoulder Belts
Safety Restraints Combination Lap and Shoulder Belts While your vehicle is in motion, the combination lap and shoulder belt adjusts to your movement. However, if you brake hard, turn hard, or if your vehicle receives an impact of 5 mph (8 km/h) or more, the lap/shoulder belt locks and helps reduce your forward movement.
Page 14 Unfastening the outboard lap/shoulder belts While the belt retracts, guide the tongue to its original position to prevent it from striking you or the vehicle. Safety Belts for Front Outboard Passenger and Rear Outboard Seating Positions Your vehicle is equipped with a dual locking mode retractor on the shoulder belt portion of the combination lap/shoulder safety belt for the front seat outboard passenger and rear outboard passengers.
Page 15 Automatic locking mode In this operating mode, the shoulder belt retractor will be automatically locked and will remain locked when the combination lap/shoulder safety belt is buckled, and does not allow the occupant freedom of movement. This mode provides the following: A tight lap/shoulder belt on the occupant.
Page 16 Shoulder Belt Height Adjustment Driver and right front passenger The driver and right front passenger shoulder belt height is adjustable to one of four (4) positions (Regular cab model) or five (5) positions (Super cab model). To adjust the belt down, push the release button on the adjuster down and slide the adjuster down.
Page 17 Safety Restraints Shoulder belt height adjuster — full up position (regular cab models)
Page 18 Adjusting shoulder belt height (regular cab models)
Page 19 Safety Restraints Shoulder belt height adjuster — full down position (regular cab models)
Page 20 Shoulder belt height adjuster — full up position (SuperCab models)
Page 21 Safety Restraints Adjusting shoulder belt height (SuperCab models)
Page 22 Shoulder belt height adjuster — full down position (SuperCab models) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. Never swing it around the neck over the inside shoulder. Never use a single belt for more than one person. Failure to follow these precautions could increase the risk and/or severity of injury in a collision.
Page 23 Safety Restraints Unfastening the outboard lap/shoulder belts Center Front Lap Belt (If equipped) The lap belt in the center of the front seat does not adjust automatically. You must adjust it to fit snugly around your hips. Do not wear it around your waist. To fasten the belt, pull the belt across your hips and insert the tongue into the correct buckle on your seat until you hear a snap and feel it lock.
Page 24 Fastening and unfastening the front center safety belt The lap belts should fit snugly and as low as possible around the hips, not around the waist. Rear Lap Belt with Retractor Pull the belt out of the retractor with a steady motion and insert the tongue into the proper buckle until you hear a snap and feel the latch engage.
Page 25: Safety Belt Maintenance
Safety Belt Extension Assembly For some people, the safety belt may be too short even when it is fully extended. You can add about eight inches (20 cm) to the belt length with a safety belt extension assembly (part number 611C22).
Page 26 Energy absorbing sew pattern...
Page 27: Air Bag Supplemental Restraint System
(slide bar) (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after any collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was...
Page 28 The Importance of Wearing Safety Belts Safety belts must be worn by all vehicle occupants to be properly restrained and help reduce the risk of injury in a collision. All occupants of the vehicle, including the driver, should always wear their safety belts, even when an air bag Supplemental Restraint System is provided.
Page 29 The Importance of Being Properly Seated In a collision, the air bag must inflate extremely fast to help provide additional protection for you. In order to do this, the air bag must inflate with considerable force. If you are not seated in a normal riding position with your back against the seatback, the air bag may not protect you properly and could possibly hurt you as it inflates.
Page 30 OFF position and the ignition switch is in ON, have the passenger air bag switch serviced at your Ford or Lincoln-Mercury dealer immediately. The passenger air bag will remain off until it is turned on. When the infant seat is removed, turn the air bag on. To turn...
Page 31 ON position and the ignition switch is in ON, have the passenger air bag switch serviced at your Ford or Lincoln-Mercury dealer immediately. The amber OFF light warns the driver and any passengers that the passenger air bag is turned off. The passenger air bag should be turned off ONLY when the rear-facing infant seat is installed at the right front or center front seats.
Page 32 How the Air Bag Supplemental Restraint System Operates The Air Bag Supplemental Restraint System consists of the driver air bag, passenger air bag (if equipped), impact sensors, a system diagnostic module, a readiness light and tone, and the electrical wiring which connects the components. The location of the air bags and warning labels...
Page 33 The driver air bag is in the center of the steering wheel. The right front passenger seat air bag (if equipped) is in the upper right hand section of the instrument panel ledge above the glove compartment. If a collision occurs, the sensors sense the severity of the impact and activate the air bags if necessary.
Page 34 Inflated driver-side air bag...
Page 35 Inflated passenger-side air bag If the air bag is inflated, THE AIR BAG WILL NOT FUNCTION AGAIN AND MUST BE REPLACED IMMEDIATELY. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 36: Safety Restraints For Children
Ford or Lincoln-Mercury dealer. Disposal of supplemental air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local Ford or Lincoln-Mercury dealer. Air bags MUST be disposed of by qualified personnel. Safety Restraints for Children In the U.S.
Page 37 Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. To prevent the risk of injury, make sure children sit where they can be properly restrained. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
Page 38 Always follow the safety seat manufacturer’s instructions when installing and using the safety seat. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 39 All child restraint systems are designed to be secured in vehicle seats by lap belts or by the lap portion of a lap-shoulder belt. If you do not properly secure the safety seat, the child occupying the seat may be injured during a collision or sudden stop.
Page 40 You can attach a tether strap anchor bracket to the cab inner back panel by using a tether anchor kit (613D74) available at no charge from any Ford dealer. Read and follow the instructions provided with the kit carefully, for installation of the child tether strap anchor.
Page 41 Follow the child seat manufacturer’s instructions to attach the tether strap to the tether bracket. Only use the tether attachment hole locations shown in the illustrations. The tether anchor may not perform properly if the wrong mounting location is used. In Super Cabs equipped with Center Facing Jump Seats, the tether strap anchor bracket should be installed only at the center of the cab’s back panel with the child seat in the front center...
Page 42 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards. Belt-positioning booster...
Page 43: Starting Your Ranger
If the parking brake is not set and the gearshift is moved out of gear, your vehicle may move unexpectedly and injure someone. A neutral tow feature is available on your vehicle. See your dealer for more information. Starting Your Ranger RWARNING...
Page 44 Do not leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. LOCK is the only position that allows you to remove the key. The LOCK feature helps to protect your vehicle from theft.
Page 45 Put the gearshift in 1 (First). Turn the ignition key to OFF. Set the parking brake fully before removing your foot from the service brake. Push and hold in the key release button. Turn the key to LOCK. Remove the key. Starting Your Ranger...
Page 46: Starting Your Vehicle
Always set the parking brake fully and make sure that the gearshift is latched in P (Park) (automatic transmission) or 1 (First) (manual transmission). Do not leave children, unreliable adults, or pets alone in your vehicle. They could accidentally injure themselves or others through inadvertent operation of the vehicle.
Page 47: Warning Lights And Gauges
Turn the key to the START position (cranking) until the engine starts. Allow the key to return to the ON position after the engine has started. If you have difficulty in turning the key, rotate the steering wheel slightly because it may be binding. Starting Your Ranger...
Page 48 For a cold engine: At temperatures 10˚F (-12˚C) and below: If the engine does not start in fifteen (15) seconds on the first try, turn the key to OFF, wait approximately ten (10) seconds so you do not flood the engine, then try again. At temperatures above 10˚F (-12˚C): If the engine does not start in five (5) seconds on the first try, turn the key to OFF, wait approximately ten (10) seconds so you do not flood the...
Page 49 An engine block heater warms the engine coolant, which improves starting, warms up the engine faster, and allows the heater-defrost system to respond quickly. Starting Your Ranger RWARNING RWARNING 20˚F ( 29˚C) or below...
Page 50 To prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. For best results, plug the heater in at least three hours before you start your vehicle. Using the heater for longer than three hours will not damage the engine, so you can plug it in at night to start your vehicle the following morning.
Page 51 Check under the vehicle again for leaking fuel. If you see or smell fuel, do not start your vehicle again. If you do not see or smell fuel, you can try to start your vehicle again. Starting Your Ranger RWARNING...
Page 52 Check all vehicle warning lights before driving your vehicle. Reset button for fuel pump shut-off switch Guarding Against Exhaust Fumes Carbon monoxide, although colorless and odorless, is present in exhaust fumes. Take precautions to avoid its dangerous effects. Never let your vehicle idle in an enclosed area, and do not sit in a parked vehicle, (with the engine running) for more than a short period of time.
Page 53 AIR CONDITIONING — Set fan speed to medium or high with the function control knob on any position (except OFF or MAX A/C) and the temperature control knob at a comfortable level. Starting Your Ranger...
Page 54 Warning Lights and Gauges The instrument panel (dashboard) on your vehicle is divided into several different sections. The illustrations on the following pages show the major parts of the instrument panel that are described in this chapter. Some items shown may not be on all vehicles.
Page 57 The Mechanical Cluster The following warning lights and gauges are on the mechanical cluster. All of the warning lights and gauges alert you to possible problems with your vehicle. Some of the lights listed are optional. The following sections detail what each of these indicators means.
Page 58 Warning Lights and Gauges Anti-lock Brake Warning Light To check the ABS brake warning light, turn the ignition key to ON. The ABS brake warning light should glow momentarily. NOTE: If the ABS brake warning light does not glow momentarily, have your vehicle’s electrical system checked immediately.
Page 59 If any of these things happen, even intermittently, have the air bag system serviced at your Ford or Lincoln-Mercury dealer immediately. RWARNING...
Page 60 Warning Lights and Gauges Air bag readiness light symbol Passenger Air Bag OFF Light The passenger air bag OFF light is located in the lower center of the instrument panel next to the passenger air bag defeat switch. This yellow indicator light illuminates whenever the passenger air bag is turned off and the ignition is on.
Page 61 Check Engine Warning Light The Powertrain On-Board Diagnostic II (OBD II) system consists of the hardware and software necessary to monitor the operation of the powertrain. The OBD II system is designed to check the function of the vehicle’s powertrain control system during normal operation.
Page 62 Warning Lights and Gauges misfiring while the last of the fuel was being consumed. After refueling, the Check Engine Warning Light will turn off after the vehicle has completed three consecutive warm up cycles without a misfire condition occurring. A warm up cycle consists of engine start from a cold condition (engine at ambient temperature) and running until the engine reaches normal operating temperature.
Page 63 Overdrive Off Indicator (If equipped) This light tells you that the Transmission Control Switch (TCS) on the gearshift lever has been pushed. When the light is on, the transmission does not shift into overdrive. Depressing the button on the shifter once more returns the vehicle to overdrive mode.
Page 64 Warning Lights and Gauges This light comes on every time you turn the ignition to the ON or START position (engine off). The light should go off when the engine starts and the alternator begins to charge. If the light stays on or comes on when the engine is running, have the electrical system checked as soon as possible.
Page 65 Fuel Reset Light (If Equipped) Your vehicle may have a fuel reset light. The fuel reset light will come on when you turn the ignition key to ON and the fuel pump shut-off switch has been triggered. Refer to Fuel pump shut-off switch in the Index to find additional information.
Page 66 Warning Lights and Gauges Battery voltage gauge — mechanical cluster Battery voltage gauge — mechanical cluster with tachometer Engine Oil Pressure Gauge This gauge indicates the engine’s oil pressure, not the oil level. However, if your engine’s oil level is low, it could affect the oil pressure.
Page 67 Check the engine’s oil level, following the instructions on checking and adding engine oil. Refer to Engine oil in the Index. If you do not follow these instructions, you or others could be injured. To assure an accurate reading, your vehicle should be on level ground.
Page 68 Warning Lights and Gauges High Beam Light This light comes on when the headlamps are turned on high beam or when you flash the lights. High beam indicator light symbol “Headlamps On” Alert Chime This chime sounds if you open the driver’s door while the headlamps or parking lamps are on, and the key is removed from the ignition.
Page 69 Fuel gauge — mechanical cluster Fuel gauge — mechanical cluster with tachometer Engine Coolant Temperature Gauge This gauge tells you the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level or mixture, the gauge indicator will not be accurate.
Page 70 Warning Lights and Gauges Turn off the engine. If you do not stop the engine as soon as safely possible, severe engine damage could result. Let the engine cool. DO NOT REMOVE COOLANT SYSTEM FILL CAP UNTIL THE ENGINE IS COOL. Check the coolant level following the instructions on checking and adding coolant to your engine.
Page 71 Speedometer The speedometer tells you how many miles (kilometers) per hour your vehicle is moving. Some vehicles are equipped with a vehicle speed (mph/km/h) limiting device that is contained within the Powertrain Control Module (PCM). The purpose of this device is to maintain peak vehicle speed below a specified limit.
Page 72 Warning Lights and Gauges Trip Odometer If you want to track your mileage up to 999.9 miles (kilometers), use the trip odometer. Simply set the trip odometer to zero by pressing the reset button firmly when beginning the distance you wish to measure. Tachometer (If equipped) The tachometer will show you the engine’s speed measured in revolutions per minute (RPM).
Page 73 Tachometer NOTE: If the 4.0L engine exceeds 5200 RPM, the PCM will restrict fuel flow to maintain engine speed at or below 5200 RPM. This function is designed to protect the engine and should be considered normal operation.
Page 75 The main controls for the climate control system, lights, lamps, clock, and radio are on the instrument panel. NOTE: Any cleaner or polish that increases the gloss (shine) of the upper part of the instrument panel should be avoided. The dull finish in this area is to help protect the driver from undesirable windshield reflection.
Page 76: Instrument Panel Controls
Instrument Panel Controls and temperature you select. The function selector control knob allows you to select heating or cooling and determine where the air will be directed. The temperature control knob setting determines the temperature of the air that flows into the vehicle. Climate control knobs To turn your air conditioner and heater system on, select any position except OFF.
Page 77 H Fan speed adjustment The H (left) knob on the control is the fan control knob which controls the volume of air flow. Rotate the H knob to the right to increase fan speed and increase the amount of air entering the vehicle.
Page 78 S (Panel and Floor) Select S to direct airflow to the floor and through the instrument panel registers at the same time. This selection can be used to either heat or cool your vehicle. The air conditioner will operate to cool the air if the outside temperature is about 50˚F (10˚C) or warmer.
Page 79 Do not put objects under the front seats that interfere with the flow of air to the back seat area. Remove any snow, ice, or leaves from the air intake area of your air conditioner and heater system that could block the air intake.
Page 80 Instrument Panel Controls Temperature selection The temperature control knob is the rotating knob located at the center of the control with tapered red and blue bands surrounding most of the knob. The wide red part of the band (full right) is the heat or warmer area. The wide blue area (full left) is the cool or unheated temperature area.
Page 81: The Interior And Exterior Lights
P (Floor & Defrost) Select P to get air to the floor and windshield defrosters at the same time. V (Defrost) Select V to obtain maximum air flow to the windshield. Rotate the temperature knob into the red area for the air temperature required to defrost.
Page 82 Rotate the thumb wheel when the headlamp control knob is in an “ON” position to brighten or dim the instrument panel lamps. Rotate fully upward to operate courtesy and cargo lamps. Headlamp control knob Fog Lamps (If equipped) The fog lamps switch is located on the instrument panel to the right of the radio and climate control.
Page 83 Fog lamp switch The fog lamps act as a supplement to the low beam headlamps under limited visibility conditions such as rain, snow, dust or fog and operate only when the low beam headlamps are on. To maximize fog lamp bulb life it is recommended that the fog lamp switch be turned off after each use prior to turning off the headlamps.
Page 84 The Daytime Running Light (DRL) system will not illuminate the tail lamps and parking lamps. Turn on your headlamps at dusk. Failure to do so may result in a collision. Lighting Up the Instrument Panel and the Interior of Your Vehicle The instrument panel lights can be turned on by turning the headlamp knob toward either the first or second position.
Page 85 Cleaning the Interior Lamps Your interior dome lamps and map lamps are plastic and should be cleaned with a mild detergent diluted in water. Rinse them with clear water. Combination Cargo and High-Mount Brakelamp The combination cargo/high-mount brakelamp is located outside the vehicle, directly over the rear window.
Page 86 Instrument Panel Controls Dome/Map Lamps (If equipped) The map lamps are located on each side of the dome light assembly. You can turn the individual map lamps on or off by sliding the switch to the left or right. To turn off, slide the switch to the middle.
Page 87: Steering Column Controls
The controls on the steering column and wheel are designed to give you easy access to the controls while you are driving. The Turn Signal Lever You can use the turn signal lever on the left side of the steering column to: operate the turn signals and cornering lamps turn the high beams on/off...
Page 88: Windshield Wipers And Washer
High Beams and Flashing the Lamps Headlamp high beam switch and turn signal lever on steering column Windshield Wipers and Washer To turn on the windshield wipers, the ignition key must be turned to the ON or ACC position. Interval wiper on turn signal lever To set the interval wipers, rotate the knob at the end of the turn signal lever toward or away from the instrument panel to the interval operation you desire.
Page 89: Steering Column Controls
Wipers in the Index. Gearshift Lever (Automatic transmission only) The gearshift lever on your Ranger is mounted on the steering column. On the end of the gearshift lever is the Overdrive On/Off button. For additional information about the gearshift lever and the Overdrive On/Off button, see the Driving Your Ranger chapter.
Page 90 OVERDRIVE OFF Lamp This lamp indicates the operating range of the transmission. This lamp illuminates when the O/D ON/OFF button is depressed. For additional information, refer to the Warning Lights and Gauges chapter. Hazard Flasher The hazard flasher is used to alert other drivers to hazardous situations.
Page 91 To use the hazard flasher: Push in the flasher button; it will pop out and the lamps will begin to flash. To stop the flashers, push in the flasher button again. NOTE: The flasher button will be sticking up slightly higher when on than when off.
Page 92 Horn To sound the horn, press the center of the horn pad. Check the horn regularly to make sure it operates properly. Horn location Tilt Steering (If equipped) Never adjust the steering column/wheel when the vehicle is moving. You could lose control of the vehicle and injure someone.
Page 93 To change the position of the steering wheel, push the release lever under the steering column away from you. Tip the steering wheel to the desired position. Pull the lever back into place to lock the steering wheel. Be sure the steering wheel locks in a notch. It is not infinitely adjustable.
Page 94 Press SET ACCEL switch and release it immediately. This will set your speed. If you keep this switch pressed, your speed will continue to increase and will not be set until the switch is released. Take your foot off the accelerator pedal. Your vehicle will maintain the speed you set.
Page 95 Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. In mountainous areas, at higher elevations, or when pulling a trailer, the speed control may not be able to maintain the preset speed with the transmission in j (Overdrive).
Page 96 Transmission control switch Accelerating With the Speed Control Operating You can use the accelerator pedal to speed up momentarily. When you take your foot off the accelerator, the vehicle will return to the set speed. Resetting the Speed Control To reset the speed control to a lower speed, press and hold the COAST switch.
Page 97 TAP-UP — This allows you to increase your current speed in increments of 1 mph (1.6 km/h) by a momentary tap of the SET-ACCEL switch. Multiple taps of the SET-ACCEL switch will increase your vehicle speed 1 mph (1.6 km/h) for each tap.
Page 98 Resuming a Set Speed If you press the brake pedal, the speed control is cancelled. You can return to the speed you set by using the RSM switch, as long as you did not press the OFF switch. To resume the speed you had before, you must be driving at least 30 mph (50 km/h).
Page 99 Features Your vehicle has a variety of features designed for your comfort, convenience and safety. Read this chapter to find out about standard and optional features. Doors Door Handles and Locks Inside handles...
Page 100 When open, the tailgate load should not exceed 500 lbs (227 kgs). If you want to load heavy items onto your vehicle, Ford recommends that you load them one at a time, directly on the bed floor to avoid damage to the tailgate or its supports.
Page 101: Features
Features To release the tailgate: Open the tailgate as directed above, but support it to allow for slack in the cables at both sides. Use a coin or similar object to pry the spring clip (on each upper cable connector) past the head of the support screw.
Page 102 Tailgate removal Do not drive your vehicle with the tailgate open unless there is a load holding it in place. Power Door Locks (If equipped) The power door lock switches are located in the front doors. To lock all doors push the switch marked s. To unlock all doors push the switch marked s.
Page 103 Features Remote Entry System (If equipped) If your vehicle has the remote entry system, you can lock or unlock the vehicle doors without using a key. The remote also has a personal alarm feature. The buttons for the system are located on the hand held transmitter that came with your vehicle.
Page 104 and the parking lamps will flash. If a door is open or ajar, the horn will give two short chirps warning you that a door is open. Remote entry personal alarm If you wish to activate the remote entry system personal alarm, press the PANIC button.
Page 105 Replacement batteries can be purchased at most pharmacies, watch stores or at your Ford or Lincoln-Mercury dealer. NOTE: The operating range of the remote entry system can also be affected by weather conditions (such as very cold temperatures) or structures around the vehicle (buildings, other vehicles, radio and TV towers, etc.).
Page 106 Replacing the batteries Replacing lost transmitters In the event a transmitter is lost, you should take your vehicle’s transmitters to your dealer to have the remote entry system deprogrammed for the lost transmitter. This is necessary to prevent further unauthorized use of the lost transmitter. You can also purchase additional transmitters (up to 4 transmitters can be used) from your dealer.
Page 107: Battery Saver
Battery Saver When the ignition is turned off, the vehicle will turn off battery voltage to all of these lights after 40 minutes: glove box, engine compartment, overhead console, mirror, courtesy and interior (including cargo) lamps. This will prevent draining of the battery if these lights have been left on inadvertently or if a door is not completely closed.
Page 108 If a door is open, the anti-theft system is prearmed and waiting for all doors to close. The THEFT indicator in the instrument panel will light continuously while the system is prearmed. Close all doors Once all doors are closed, if any were open, the system will begin a 30 second countdown to become armed.
Page 109 When unlocking the vehicle with a key, turn the key all the way to the end of its travel or the system may not disarm. NOTE: The flashing lights and honking horn will shut off automatically within 2 minutes 45 seconds after the system is triggered.
Page 110 Sliding rear window operation SuperCab quarter windows (if equipped) To open the optional flip quarter windows on the Ranger SuperCab models, follow the operating instructions shown in the following illustration. SuperCab flip open quarter window...
Page 111 Using the Power Windows (If equipped) Each door has a power control that opens and closes the window on that door. The driver’s door has a master control switch that operates all door windows. You must place the ignition switch in the ON or ACC position to use your power window controls.
Page 112 Seats Head Restraints If you use them properly, head restraints are intended to help protect your head and neck in a collision. Adjust the head restraints so that the cushion contacts the back of your head when you move your head rearward. If you have a front bench seat, you can adjust the front seat head restraints for your comfort and protection.
Page 113 Release the lever to lock the seat in its new position. Make sure the seat locks securely in place. Adjusting the bench seat Adjusting the bucket seat SuperCab To move the front seat forward or rearward: Find the adjustment bar at lower front of the front seat. Lift bar upward to unlatch the seat.
Page 114 Move the seat to the desired position. Release the bar to latch the seat in its new position. Make sure the seat latches securely in place. Adjusting the bucket seat Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Page 115 To reduce the risk of serious injury in a collision, children should always ride with the seatback upright. Reclining Bucket Seats (If equipped) If your vehicle is equipped with the optional reclining bucket seat, you can tilt the seatback up to 30 degrees rearward. On the side of the seat, find the handle for the recliner.
Page 116 Reclining bucket seat Center Facing Jump Seat — SuperCab Only To open the seat, pull inboard and down on the seat handle. To stow the seat, pull seat bottom back to the fully upright position. The jump seats should be kept in the stored position for easier access to the rear cab area.
Page 117 Do not install a child seat in a center facing jump seat. Tilt Slide Seat (If equipped) SuperCab only With the front seatback tilted forward, the tilt slide seat can be moved to provide additional entry space to access the rear seat compartment of the vehicle.
Page 118 NOTE: The seat can no longer be moved rearward when in its latched position. Tilt slide seat Prior to operating the vehicle, check to ensure that the seat assembly is locked by pushing or pulling the seat forward or rearward. If seat does not lock, repeat steps 2 and 3. Locking tilt slide seat...
Page 119 To operate the seat adjuster: To adjust the seats forward or rearward, locate the release bar at the lower front area of the seat cushion. Lift the release bar and hold until the desired seat position is obtained, then release the bar to relock the seat. Adjusting seat 60/40 Split Front Bench (If equipped) The seat back release operates the same as the basic bucket seat.
Page 120 Using the Power Seats (If equipped) If your vehicle has the power seat option, you can adjust it in several directions. The controls are on the outboard side of the seat. The power controls on the driver’s seat Using the Power Lumbar Support and Side Bolsters (If equipped) Inflating the lumbar support and side bolsters If your vehicle is equipped with this option you can...
Page 121 To inflate the lumbar support pad, push the “+” end of the rear rocker switch. To deflate the lumbar support pad, push the “ ” end of the switch. Power lumbar and side bolsters switch — sport bucket seat Cleaning the Seats Fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner.
Page 122 Mirrors Dual Electric Remote Control Mirrors (If equipped) To adjust the remote controlled side mirrors: Find the control switch in the driver’s door panel. Select the right or left mirror by moving the selector switch to the right or left. Move the control knob in the direction you want to move the mirror.
Page 123 Features Console (If equipped) Your vehicle may have a full console. The full console has the features shown in the illustration below. The features on the console — bucket seats...
Page 124 Storage armrest — 60/40 split bench Floor Mounted Cupholders (If equipped) If your vehicle has a bench seat, you may have floor mounted cupholders. On manual transmission vehicles, the cupholders are located on the floor on either side of the gearshift lever. On automatic transmission vehicles a removable consolette is located on the floor.
Page 125 Features Floor mounted cupholders — manual transmission Floor mounted cupholders — automatic transmission...
Page 126 To remove the automatic transmission consolette: Pull the adjustable portion of each cupholder from the consolette. Remove the rubber pad at the bottom of each cupholder. Using a quarter, turn the slotted head at the bottom of each cupholder 90˚ (one quarter turn). Lift the consolette from the floor and secure it in a safe place.
Page 129: Electronic Sound Systems
Premium Stereo Cassette and Stereo Cassette with CD DJ Using the Controls on Your New Radio How to turn the radio on and off Press the “VOL/PUSH” knob to turn the radio on. Press again to turn it off. How to adjust the volume Turn the “VOL/PUSH”...
Page 130 How to tune radio stations There are four ways for you to tune in a particular station. You can use the “TUNE”, “SEEK”, “SCAN” or the memory buttons. Using the “TUNE” function You can change the frequency up or down one increment at a time by pressing and releasing either the left ( b ) or right ( a ) side of the “TUNE”...
Page 131 Setting the station MEMORY PRESET buttons Your radio is equipped with 6 station memory buttons. These buttons can be used to select up to 6 preset AM stations and 12 FM stations (6 in FM1 and 6 in FM2) Follow the easy steps below to set these buttons to the desired frequencies: Select a band, then select a frequency.
Page 132 Adjusting the tone balance of your radio Increasing or decreasing bass response Press the top ( c ) of the “BASS” button to increase bass; press the bottom ( d ) of the “BASS” button to decrease bass. Increasing or decreasing treble response Press the top ( c ) of the “TREBLE”...
Page 133 Using the Controls of Your Cassette Tape Player NOTE: Radio power must be on to use the cassette tape player. How to insert a tape Your cassette tape player is equipped with power loading. Once you insert a tape and push slightly (with the open edge to the right), the loading mechanism draws the tape the rest of the way in and play will begin after a momentary tape tightening process.
Page 134 Using the “SEEK” function with your cassette tape player While in the tape mode, push the right ( a ) side of the “SEEK” button to seek forward to the next selection on the tape. Push the left ( b ) side to seek the previous tape selection.
Page 135 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford Cassette Cleaning Cartridge to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 136 Clock Operation How to view the clock mode Press the “CLK” button to display time. The time will continue to be displayed until a radio or tape function is chosen. After approximately 10 seconds, the time will again appear in the display.
Page 137 Ford 6-CD Changer (If equipped) The Ford Ranger (Regular Cab) 6-CD Changer is mounted behind the driver’s seat. The Ford Ranger (SuperCab) 6-CD Changer is mounted on the floor near the center of the rear cab wall. Both changers are controlled with buttons on the Audio System.
Page 138 Push the “i” button to eject the disc “magazine” (holds 6 discs) (Figure 2). Figure 2 Load discs into the disc magazine slots (numbered 1 through 6) one at a time with labeled surfaces upward, starting with bottom slot number 1 (Figure 3). Figure 3...
Page 139 How to Operate the Ford 6-CD Changer Using the Controls on the Radio (Premium Audio Systems only) If your vehicle is equipped with the Ford 6-CD Changer System, you can operate it through the controls of your Premium Audio System.
Page 140 If the CD Changer is empty, “NO” and “DISC” will flash in the display and radio play will continue. How to change the disc being played When in the CD mode, you can change discs by pressing the right side ( a ) of the “TUNE DISC” button (to select the next discs) or the left side ( b ) of the “TUNE DISCS”...
Page 141 Electronic Sound Systems Operating the CD Compression feature Because of the wide dynamic range of Ford’s 6-CD Changer System, soft passages may be difficult to hear under certain driving conditions while maintaining a reasonable volume level in the louder passages. The compression feature will bring these soft and loud passages closer together for a more consistent listening level.
Page 142 CD format. Because of this, a new disc that is free of dust and scratches could be defective and may not play on your Ford Compact Disc Player. If play does not begin after the CD button is pushed: The radio is not on.
Page 143 If the sound skips: Badly scratched discs or extremely rough roads will cause the sound to skip. Skipping will not damage the disc player or scratch the discs. How to take care of and clean the CD Changer and discs To ensure the continued performance of your CD Changer carefully read the following precautions: Always handle a disc by the edge.
Page 146 Midline Stereo and Stereo Cassette Radio Using the Controls on Your New Radio How to turn the radio on and off Press the “VOL/PUSH ON” knob to turn the radio on. Press again to turn it off. How to adjust the volume Turn the “VOL/PUSH ON”...
Page 147 Electronic Sound Systems Using the ”TUNE“ function You can change the frequency up or down one increment at a time by pressing and releasing either the left ( b ) or right ( a ) side of the ”TUNE“ button. Manual tuning adjusts your radio to any allowable broadcast frequency, whether or not a station is present on that frequency.
Page 148 Follow the easy steps below to set these buttons to the desired frequencies: Select a band, then select a frequency. Press one of the memory preset buttons and hold the button until the sound returns. That station is now held in memory on that button.
Page 149 NOTE: Illuminated bars in the display show relative levels of bass and treble, and positions of speaker balance and fader functions (left to right, front to rear). Using the Controls of Your Cassette Tape Player NOTE: Radio power must be on to use the cassette tape player or eject a tape.
Page 150 Using the ”SEEK“ function with your cassette tape player While in the tape mode, push the right ( a ) side of the ”SEEK“ button to seek forward to the next selection on the tape. Push the left ( b ) side to seek the previous tape selection.
Page 151 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford Cassette Cleaning Cartridge to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 152 NOTE: The clock can be displayed or set whether the ignition is on or off. How to set the clock Turn the radio on. Press and hold the ”CLK“ button, press the right ( a ) side of the ”SEEK“ button to increase hours. Press the left ( b ) side of the button to decrease hours.
Page 153 Electronic Sound Systems When the radio waves are reflected off objects or structures, the reflected signal cancels the normal signal, causing the antenna to pick up noise and distortion. Cancellation effects are most prominent in metropolitan areas, but also can become quite severe in hilly terrain and depressed roadways.
Page 154 Ask your dealer for a copy of this limited warranty. Service At Ford Electronics, we stand behind our audio systems with a comprehensive service and repair program. If anything should go wrong with your Ford audio system, return to your dealer for service.
Page 155: Driving Your Ranger
Light (O/D OFF), which is located on the instrument cluster, may flash steadily if a malfunction has been detected. If the Overdrive Off Indicator Light is flashing, contact your Ford dealer as soon as possible. If this condition persists, damage to the transmission could occur.
Page 156 Putting Your Vehicle in Gear Your vehicle’s gearshift is on the steering column. The transmission control switch is located on the end of the gearshift lever. You can put the gearshift in any of the several positions. The positions of the column-mounted gearshift Transmission control switch (located on the end of the gearshift lever) Hold the brake pedal down while you move the gearshift lever from position to position.
Page 157: Driving Your Ranger
Please refer to the chapter titled Servicing Your Ranger in this Owner Guide for instructions on checking and replacing fuses.
Page 158 N (Neutral) With the gearshift in the N (Neutral) position, the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. Driving When to use j (Overdrive) This is the normal driving position. As the vehicle picks up speed, automatic upshifts to second, third and fourth gears will occur when j Overdrive is chosen on the selector and the transmission control switch has not been pressed.
Page 159 Driving Your Ranger Transmission control switch (located on the end of the gearshift lever) To return the transmission to the normal j Overdrive operation, press the transmission control switch again. The Transmission Control Indicator Light will not be illuminated when Overdrive operation resumes. This switch may be used to select O/D ON or O/D OFF any time the vehicle is being driven.
Page 160 P (Park) Always come to a complete stop before you shift into P (Park). This position locks the transmission and prevents the rear wheels from turning. To securely latch the gearshift in the P (Park) position, pull it toward you, push it completely counterclockwise against the stop, and then push it toward the instrument panel.
Page 161: Manual Transmission Operation
These actions will seriously reduce clutch life. Driving with your foot resting on the clutch may cause the vehicle to jerk sharply when pressing or removing your other foot from the accelerator. Driving Your Ranger...
Page 162 Shifting the Gears The gearshift for a manual transmission is mounted on the floor. The gearshift pattern consists of seven positions: Neutral, five forward gears, and Reverse. 5-Speed Overdrive manual transmission shift pattern Backing up To shift into R (Reverse): Push the clutch pedal in all the way to the floor and hold it.
Page 163 If R (Reverse) is not engaged, continue to push the clutch pedal in while you put the gearshift back into Neutral. Then, release the clutch pedal for a moment and repeat steps 2 through 5. Upshifting/downshifting Upshift and downshift at the speeds that are specfied in the charts. Driving Your Ranger...
Page 164 Recommended Shift Speeds Engines with 5-Speed Manual Overdrive Transmission...
Page 165 Parking To park your vehicle, apply the service brake pedal, and shift into N (Neutral) while still maintaining pressure on the service brake. Set the parking brake fully. Shift into first and turn off the ignition. Driving Your Ranger RWARNING...
Page 166: Steering Your Vehicle
Steering Your Vehicle Your Ranger may have optional power steering. Power steering uses energy from the engine to help steer your vehicle. If the amount of effort needed to steer your vehicle changes at a constant vehicle speed, have the power steering system checked.
Page 167 Driving Your Ranger Four-Wheel Drive (4WD) System (If equipped) When you select the 4WD mode, your vehicle uses all four wheels to power itself. This increases traction, enabling you to drive your 4x4 over terrain and road conditions not travelled normally by two-wheel drive vehicles.
Page 168 Transfer case selections Four-wheel drive operation (4H or 4L) on dry pavement is not recommended. Operating the vehicle in four-wheel drive on dry pavement will increase tire wear, decrease fuel economy, and make four-wheel drive disengagement difficult for the transfer case.
Page 169 2H and 4H (or 4H to 2H) may take place at any speed. Locking hub positions NOTE: Do not drive the vehicle in 4H or 4L with the manual locking hubs in the FREE position. Driving Your Ranger...
Page 170 NOTE: Do not drive the vehicle with the left and right manual locking hubs set to different positions. To shift from 4H to 2H: Move the transfer case shift lever forward to the 2H position. This can be done at any speed. However, the front driveline will remain engaged to the front wheels until the manual locking hubs are disengaged.
Page 171 Four-wheel drive operation (4x4 HIGH or 4x4 LOW) on dry pavement is not recommended. Operating the vehicle in four-wheel drive on dry pavement will increase noise, vibration, tire wear, decrease fuel economy, and make four-wheel drive disengagement difficult for the transfer case. Driving Your Ranger RWARNING...
Page 172 Electric shift system indicator lights A 4WD indicator light and a 4WD LOW indicator light are located in the instrument cluster. If either light flashes, take your vehicle in for service. Two-Wheel Drive mode — Neither the 4WD nor the 4WD LOW lights are lit.
Page 173 For prolonged two-wheel drive operation on dry pavement, disengagement of the automatic locking hubs, which is not required for two-wheel drive operation, stops all movement of front-wheel drive components while operating in two-wheel drive. Driving Your Ranger...
Page 174 During axle break-in or operation in extremely cold temperatures, the automatic locking hubs may not release completely. It may be necessary to drive the vehicle for 10 to 15 minutes before repeating the release procedure. To shift from 4x4 HIGH or 2WD to 4x4 LOW: Stop the vehicle, depress the brake and place the automatic transmission in N (Neutral) or depress the clutch on vehicles with a manual transmission.
Page 175 If the ignition system gets wet, the vehicle may stall. Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly, while applying light pressure on the brake pedal. Driving Your Ranger...
Page 176 After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts causes an imbalance which could damage drive components. NOTE: If the transmission and transfer case is submerged in water, their fluids should be checked and changed, if necessary.
Page 177 These two circuits are supplied by a common hydraulic brake fluid reservoir, with a fluid level sensor. The brake light in the instrument cluster will light for low brake fluid in the common brake fluid reservoir. Driving Your Ranger RWARNING...
Page 178 An increase in pedal travel will result in reduced braking capability. The brake system should be checked immediately. Rear Anti-lock Brakes Your vehicle may be equipped with a Rear Anti-lock Brake System. This system prevents at least one and often both rear wheels from completely locking up when the brakes are applied in a panic stop, for example.
Page 179 Anti-lock stop will diminish braking effectiveness. During an Anti-lock stop, the driver will notice a brake pedal pulsation and hear some noise from the engine compartment. This is an indication that the 4WABS system is working correctly and is normal. Driving Your Ranger RWARNING...
Page 180 Anti-lock system. NOTE: Mobile phones or radio transmitters not installed by Ford Motor Company may interfere with the Anti-lock System. Should the Anti-lock system activate unexpectedly or the Anti-lock Warning Light illuminate after installation of such a unit, have the installation of the unit checked.
Page 181 If pull occurs during the first 500 miles (800 km), make 10 moderately fast stops from 40 mph (65 km/h) and then perform the self-adjustment procedure above. It may be necessary to repeat this operation to properly seat new brake linings and pads. Driving Your Ranger RWARNING...
Page 182 Stopping Distances Stopping distances vary with different loads and driving conditions. Use caution when encountering new conditions and acquaint yourself with vehicle performance. Take full advantage of engine braking power when slowing down. Applying the Brakes Apply the brake pedal gradually. Use the “squeeze” technique —...
Page 183 With the transfer case in N (Neutral), the vehicle is free to move with either the automatic transmission in P (Park) or with the manual transmission in any driving gear. Driving Your Ranger RWARNING...
Page 184 Do not leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. To release the parking brake, press the service brake pedal with your right foot and hold the parking brake pedal down with your left foot while you pull the parking brake release lever.
Page 185 For 4x4 vehicles, engage 4WD, and try to drive away. High Speed Driving Ford Motor Company recommends obeying posted speed limits. Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components.
Page 186 Pump the brake pedal steadily and evenly to avoid locking your front wheels (except with 4WABS). To stop on ice, shift to N (Neutral) below 10 mph (15 km/h) and gently pump brakes (except with 4WABS). Consider using one of the lower gears. For 4x4 vehicles, engage 4WD, and try to drive slowly away.
Page 187 Shift in a steady rhythm between forward and reverse gears. Allow the transmission to fully engage, then press lightly on the accelerator. Do not rock the vehicle for more than a few minutes. This may overheat the Driving Your Ranger RWARNING...
Page 188 engine and transmission, causing damage to both. In addition, other vehicle systems and components may also be damaged. Do not spin the wheels at over 35 mph (55 km/h). The tires may fail and injure a passenger or bystander. Driving With a Heavy Load There are limits to the amount of weight your vehicle can carry or tow.
Page 189 Driving Your Ranger Secure all items in cargo area to prevent them from falling out and creating a safety hazard on the roadway. Cargo tie-down holes...
Page 190 Cargo tie-down hooks — Splash pickup box Loading sheets of building material Four-foot (122 cm) wide sheets of building or other material will not fit flat on the pickup box floor. However, support pockets in the pickup walls permit up to 500 lb (227 kg) of this type cargo to be carried on crossbody mounted 2“...
Page 191 Driving Your Ranger Loading four foot (122 cm) building material sheets (styleside box only) Vehicle/Trailer Loads All vehicles may tow a Class I trailer provided the Gross Combined Weight (GCW) is less than or equal to the GVWR shown on the Safety Compliance Certification Label. For heavier trailer applications, refer to the towing information found later in this chapter.
Page 192 Vehicle Loading/Towing Information and the Trailer Towing Tables to determine the specific towing capability of your vehicle. Stay within the load limits when you tow. Carefully and thoroughly prepare your vehicle for towing, making sure to use the right equipment and to attach it properly.
Page 193 Be sure everyone in your vehicle is in a seat and using a safety belt properly. Each additional item of equipment affects how much cargo a vehicle can carry. If a vehicle is overloaded, performance will suffer and service concerns may arise. Driving Your Ranger RWARNING RWARNING RWARNING...
Page 194 The following is a typical example of a Safety Compliance Certification Label and an explanation of how this information should be used: Safety Compliance Certification Label Do not use the sample numbers on the Safety Compliance Certification Label shown. Use the actual numbers from your vehicle certification label.
Page 195 It is Gross Vehicle Weight Rating minus the base curb weight. Gross Vehicle Weight (GVW) If you add base curb weight and the weight of a load (including passengers, cargo and optional equipment) being carried at a particular time, you get the Gross Vehicle Weight (GVW). Driving Your Ranger...
Page 196 It is important to remember that GVW is not a limit or a specification. If an owner loads up a vehicle and weighs it, that’s the GVW at that moment. If the owner piles on more of a load and weighs it again, that becomes the GVW. Gross Vehicle Weight Rating (GVWR) To avoid overloading a vehicle, the owner should observe the manufacturer’s specified Gross Vehicle Weight Rating.
Page 197 Driving Your Ranger Passenger car type tires when installed on light trucks and multipurpose passenger vehicles are rated at 10% lower load carrying capacity due to the differences in vehicle usages. The vehicle must not be loaded to both the front and rear GAWR because the GVWR will be exceeded.
Page 198 The trailer weight range is a specified range by weight, which the trailer must fall within, ranging from zero to the maximum trailer weight rating. NOTE: Ranger pick-ups are not recommended for slide-in camper usage. Calculating The Load To know how much weight your vehicle can carry:...
Page 199 Driving Your Ranger Sample label If you suspect that your payload is excessive, have your vehicle weighed at a highway weigh station or appropriate commercial facility. Weigh the total vehicle and trailer (if applicable), then separately weigh the vehicle at the front and rear wheels. And...
Page 200 Use this chart to perform your calculations. NOTE: The Truck Safety Compliance Certification Label has two weight related entries that sometimes cause confusion.
Page 201 (passengers, accessory equipment and cargo). These combined weights should fall below the vehicle’s GVWR and GAWR. Camper Bodies NOTE: Your Ranger Pickup is not recommended for slide-in camper bodies.
Page 202 Trailers Towing a trailer safely means having the proper weight on the tongue (usually 10% of the trailer weight). Load-equalizing hitches on large rigs may transfer weight to each of the vehicle’s axles. This weight must be included in capacity calculations when determining if the vehicle is loaded within safe limits.
Page 203 Driving Your Ranger...
Page 205 Driving Your Ranger Manual Transmissions...
Page 207 Driving Your Ranger...
Page 209 Driving Your Ranger Automatic Transmissions...
Page 211 Driving Your Ranger...
Page 213 If you are not certain that you are using the right equipment in the proper manner, see your Ford or Lincoln-Mercury dealer. Hitches For towing trailers up to 2,000 lb (907 kg), use a weight carrying hitch and ball which uniformly distributes the trailer tongue loads through the underbody structure.
Page 214 NOTE: The rated capacities (as shown in this guide) for trailer towing with the factory bumper are only valid when the trailer hitch ball is installed directly into the ball hole in the bumper. Addition of bracketry to either lower the hitch ball position or extend the hitch ball rearward will significantly increase the loads on the bumper and its attachments.
Page 215 Shift back to j (Overdrive) whenever practical for optimum powertrain cooling and fuel economy. This can be accomplished by pushing in the transmission control switch which is located on the end of the gearshift lever. Driving Your Ranger RWARNING...
Page 216 When descending a steep grade with a trailer, operate in Drive rather than Overdrive. If additional braking is needed, shift the automatic transmission gearshift into 2 (Second) gear or 1 (Low). Servicing Your Vehicle If You Tow If you tow a trailer for a long distance, your vehicle will need to be serviced more frequently than usual.
Page 217 Set the parking brake fully. Shift an automatic transmission into Park (P). Put the gearshift of a manual transmission in Reverse. If your vehicle is equipped with four-wheel drive make sure the transfer case is not in Neutral. Driving Your Ranger RWARNING...
Page 218 Any modifications to the suspension or steering systems can reduce your vehicle’s performance capability and adversely affect driver and passenger safety. Ford recommends that you DO NOT make modifications such as adding or removing parts (like lift kits, stabilizer bars or snowplowing equipment) or by using replacement parts non-equivalent to the original factory equipment.
Page 219: Roadside Emergencies
Jump-Starting Your Vehicle Your vehicle’s battery may die if you leave the lights on or any electrical equipment on after you turn the engine off. If this happens, you may be able to jump-start your vehicle with a booster battery. The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes.
Page 220 Do not push-start your vehicle. You could damage the catalytic converter. For further information, see Jumper Cables in the Index. To avoid damage or injury, follow these directions in the order they are given. If in doubt, call for road service. Preparing Your Vehicle Your vehicle has a 12-volt starting system, so you need to use a 12-volt jumper system.
Page 221: Roadside Emergencies
Connecting the jumper cables Connect one end of the first jumper cable to the positive (+) terminal of the discharged battery. (You can connect either jumper cable to the positive (+) terminal, as long as you use the same cable for both positive terminals.) Most jumper cables have a red cable and a black cable.
Page 222 Attaching jumper cables Jump-Starting Make sure that the jumper cables are not in the way of moving engine parts, then start the booster vehicle. Run the engine at a moderate speed. Let the discharged battery charge for a few minutes and then start the disabled vehicle.
Page 223: Changing A Tire
“relearned.” You may need to use a battery charger to fully recharge the battery. If you need to replace your battery, see Battery in the Servicing Your Ranger chapter. Changing a Tire If you get a flat tire while you are driving, do not apply the brake heavily.
Page 224 It is not recommended that the vehicle be operated in the 4WD modes with a temporary spare. If 4WD operation is necessary, do not operate at speeds above 10 mph (16 km/h) or for distances above 50 miles (80 km). Extended operation in 4WD with a temporary spare may result in damage to powertrain components.
Page 225 drive through an automatic car wash with this tire. Because the temporary spare tire is smaller than a conventional tire, it reduces the ground clearance. Your vehicle may get caught in the rails and it could be damaged. Spare Tire Location The spare tire for your vehicle is stowed at the rear under the frame.
Page 226 To remove the spare tire: Use the hex portion of the lug nut wrench to remove the bolt that fastens the hinge to the channel. Swing the hinge away and lower the channel. Unscrew the retaining bolt using the tapered end of the lug nut wrench through the eye of the bolt.
Page 227 Preparing to Change the Tire NOTE: To lift your vehicle by other than the front or rear jacking points, be sure to use only hoist adapters with a wide contact surface. Make sure that your vehicle will not move or roll. If you have an automatic transmission, put the gearshift in Park.
Page 228 Jack handle location and installation The jack and lug nut wrench are stowed behind the passenger’s seat. The jack handle is stowed under the hood on the radiator support. Jack stowage Jack stowage...
Page 229 Insert the tapered end of the lug nut wrench behind wheel covers or hubcaps and twist off. Use only the lug nut wrench provided to remove wheel ornaments. Not using the tapered end of the lug nut wrench at the pry-off notches may result in damage to the finish of the wheel and ornament.
Page 230 Front axle jacking point c. Turn the jack handle clockwise until the wheel is a maximum of one inch off the ground. Rear axle jacking point NOTE: Do not use the differential housing as a lift point.
Page 231 To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. Remove the lug nuts with the lug nut wrench.
Page 232 Lug nut tightening sequence Use of wheels or lug nuts other than original equipment could cause damage to the wheel or mounting system and allow the wheels to come off while the vehicle is in motion. Replace any wheel covers, ornaments, or hub caps that your vehicle has.
Page 233 Retighten the wheel lug nuts to the specified torque at 500 miles (800 km) of new vehicle operation and at intervals specified in the Maintenance Schedule and Record booklet. Also retighten to the specified torque at 500 miles (800 km) of operation after any wheel change or any time the lug nuts are loosened.
Page 234: Towing Your Vehicle
If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. Ranger 4x2/4x4 The recommended method to tow your Ranger is with flatbed or wheel lift equipment. However, slingbelt towing is acceptable. Ranger without rear bumper The recommended method to tow your Ranger is with flatbed or wheel lift equipment.
Page 235 Roadside Emergencies When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for the proper...
Page 236 Recreational Towing — All wheels on the ground Towing your vehicle can be successfully performed by following the appropriate guidelines for the type of powertrain on the vehicle to be towed. The following guidelines, by powertrain combination, are designed to ensure that the transmission is not damaged due to insufficient lubrication.
Page 237 4 x 2 — Manual transmission Release the parking brake. Place the transmission gearshift in the neutral position. Maximum speed is limited by towing equipment manufacturer’s recommendation, unlimited distance. 4 x 4 — Manual shift transfer case Release the parking brake. Place the transmission gearshift in the neutral position.
Page 238 Mark the driveshaft and transfer case/axle flanges to ensure proper position when installing the driveshaft. Refer to service manual for proper driveshaft torque specification. When disconnecting/installing the driveshaft, the parking brake must be set and the wheels blocked to ensure the vehicle does not roll.
Page 239 To return the vehicle to a towable condition, you must: Place the transfer case in 2WD by rotating the 4WD switch to 2WD. NOTE: Both the 4WD and 4WD Low indicator lights in the instrument cluster will be off when the transfer case is in 2WD.
Page 240: Customer Assistance
To purchase Roadside Assistance coverages beyond this period (available through Ford Auto Club in the United States or Ford and Lincoln-Mercury dealers in Canada), contact your Ford or Lincoln-Mercury dealer. Additional Roadside Assistance coverage is unavailable in Puerto Rico and the Virgin Islands.
Page 241 Service/Maintenance Concerns (U.S. or Canada) Ford recommends taking your vehicle to your selling dealer who wants to ensure your continued satisfaction. You may, however, take your vehicle to any authorized Ford or Lincoln-Mercury dealer.
Page 242 Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this process at any time without notice and without incurring...
Page 243 What Kind of Cases Does the Board Review? The Board reviews unresolved warranty performance complaints on Ford, Mercury and Lincoln cars and Ford and Mercury Light Trucks under warranty that have not been resolved by a dealer or Ford Motor Company, except those involving:...
Page 244 It will also provide you with a form to indicate your acceptance or rejection of an award decision. The decisions of the Board are binding on the dealer and Ford, but customers may have other options available to them under state or federal law.
Page 245 Board address. At the same time, your dealer and Ford Motor Company representative are asked to submit statements. To review your case properly, the Board needs the following...
Page 246: Reporting Safety Defects
However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in the Washington, D.C.
Page 247 Ford of Canada Customer Assistance Ford Motor Company of Canada, Limited If you live in Canada and have any questions or concerns that the dealership cannot answer, contact the Customer Assistance Centre. Please have the following information available when contacting...
Page 248 Mediation/Arbitration Program (Canada only) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 249 Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write to: If you are in other foreign countries, contact the nearest Ford dealership. If the dealership cannot help you, they can direct you to the appropriate Ford affiliate office.
Page 250: Accessories
Accessories Ford Accessories for Your Vehicle Ford has many fine products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following, or products of equivalent quality: A wide selection of accessories is available through your local authorized dealer.
Page 251 Safety, Comfort, and Convenience...
Page 252 NOTE: Because we have no control over the installation, design, or manufacture of such systems, Ford cannot assume responsibility for any adverse effects or damage that may result if you use this equipment.
Page 254 Accessories...
Page 256: Servicing Your Ranger
Service Made Easy Ford has two goals for servicing your vehicle. When we can, we design parts that do not need to be serviced. We want to make servicing your vehicle as easy as possible. To help you: We highlight do-it-yourself items in yellow in the engine compartment so that you can find them easily.
Page 257 NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for disposing of these types of fluids. Call your local recycling center to find out about recycling automotive fluids. Precautions When Servicing Your Vehicle Be especially careful when inspecting or servicing your vehicle. Here are some general precautions for your safety: If you must work with the engine running, avoid wearing loose clothing or jewelry that could get caught in moving...
Page 258 N (Neutral) position. Block the wheels. This will prevent your vehicle from moving unexpectedly. Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Servicing Your Ranger RWARNING...
Page 259 Opening the Hood Pull the hood release handle, located below the steering column. Hood release handle While applying upward pressure on the hood, lift the hood latch handle located in the opening between the hood and upper portion of the grille near the center, to your left, as you face the front of the vehicle.
Page 260 Be sure to oil the hood latch every six months to maintain smooth operation. Always attempt to lift the hood after closing to be sure it is securely latched. Servicing Your Ranger...
Page 261: Engine Compartment
Engine Compartment Your vehicle has one of the following types of engines: A 2.3 Liter EFI, I-4 twin plug engine, or A 3.0 Liter SEFI, V-6 engine or A 4.0 Liter SEFI, V-6 engine. The following pages show diagrams of each engine type and where to find items that you should regularly service.
Page 265: Filling The Fuel Tank
Cleaning the Engine A clean engine is more efficient because a buildup of grease and dirt acts as an insulator, keeping the engine warmer than usual. Extreme care must be used if a power washer is used to clean the engine. The high pressure fluid could penetrate sealed parts and assemblies causing damage or malfunctions.
Page 266 To replace and secure the fuel cap; place it in position and rotate it clockwise until it clicks (ratchets). Doing so will not damage or break the fuel cap. The ratcheting mechanism allows the fuel cap to be sealed without overtightening. Servicing Your Ranger RWARNING...
Page 267 If you lose the fuel cap, replace it with an authorized Motorcraft or equivalent part. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision.
Page 268 Servicing Your Ranger Choosing the Right Fuel Use only UNLEADED FUEL in your vehicle. Using leaded fuel is prohibited by federal law. Your warranty may not apply if your vehicle is damaged because you used the wrong fuel. Vehicle inspection programs may detect misfueling. Under these circumstances, you may be required by law to make costly repairs at your own expense.
Page 269 In some parts of the country, “premium” grade fuels are sold with octane ratings of less than 91, especially in high altitude areas. It is recommended that you use only those “premium” fuels with an octane rating of 91 or higher. Fuel Quality If you are experiencing starting, rough idle or hesitation problems when the engine is cold, it may be caused by fuel...
Page 270 If any fuel is swallowed, call a physician or poison control center immediately. Do not delay calling a physician merely because no adverse effects are noticed at first; the toxic effects of fuels may not become apparent for many hours. Servicing Your Ranger RWARNING...
Page 271 If gasoline is swallowed, do not induce vomiting. If a gasoline-methanol blend is swallowed, induce vomiting under the direction of a physician or poison control center. Gasoline and gasoline-methanol blends may contain small amounts of carcinogens, such as benzene. Long-term exposure to unleaded gasoline vapors has caused cancer in laboratory animals.
Page 272 In metric, multiply the number of liters used by 100 and divide the answer by the number of kilometers traveled. This will give you the number of liters used per 100 km. Servicing Your Ranger...
Page 273 Comparisons With Environmental Protection Agency (EPA) and Transport Canada (TC) Fuel Economy Estimates EPA fuel economy figures are obtained from laboratory tests under simulated road conditions and may not reflect the actual conditions you experience or your style of driving. The EPA fuel economy estimate is not a guarantee that you will achieve the fuel economy shown.
Page 274 Engine Oil Recommendations We recommend using Motorcraft oil or an equivalent oil meeting Ford Specification WSS-M2C153-F and displaying the American Petroleum Institute CERTIFICATION MARK on the front of the container. The API Certification Mark Never use: “Non-Detergent” oils Oils labeled API SA, SB, SC, SD, SE, SF or SG...
Page 275 Checking and Adding Engine Oil Since the proper amount of engine oil is important for safe engine operation, check the oil using the dipstick each time you put fuel in your vehicle. Remember the engine must be off, the oil must be warm and the vehicle must be parked on level ground.
Page 276 Servicing Your Ranger It may be necessary to add some oil between oil changes. Make sure you use a CERTIFIED engine oil of the preferred viscosity. Your vehicle’s warranty coverage may not apply if engine damage is caused by the use of improper engine oil.
Page 277: Engine Coolant
NOTE: See Refill Capacities, Motorcraft Parts and Lubrication Specifications in this chapter for the appropriate oil filter and engine oil refill quantity. NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for disposing of these types of fluids. Call your local recycling center to find out about recycling automotive fluids.
Page 278 When you are sure that all the pressure has been released, use the cloth to turn and remove cap. Stand away from the radiator opening. Hot steam may blow out or hot engine coolant may even splash out. Adding engine coolant Adding engine coolant Servicing Your Ranger RWARNING...
Page 279 Be careful not to add engine coolant to the windshield washer fluid reservoir. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. When the engine is cool, add a 50/50 mixture of engine coolant and water to the engine coolant recovery reservoir —...
Page 280 Ford specification ESE-M97B44-A. Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for 4 years or 50,000 miles (80,000 km). Do not use alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze.
Page 281 Severe winter climate If you drive in extremely cold climates (less than -34˚F [-36˚C]), it may be necessary to increase the coolant concentration above 50%. Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle is such that the coolant will not freeze at the temperature level in which you drive during winter months.
Page 282 Visual inspection can determine if the washer fluid is adequate. Do not operate the washer when the reservoir is empty. Do not put windshield washer fluid in the container for the engine coolant. Servicing Your Ranger RWARNING...
Page 283 Adding windshield washer fluid Use specially formulated windshield washer fluid rather than plain water, because specially formulated washer fluids contain additives that dissolve road grime. For safety reasons, washer fluids containing an appropriate antifreeze such as methanol should be used in freezing weather (temperatures below 32˚F [0˚C]).
Page 284 To remove wiper blade assembly from wiper mounting arm, depress lock tab and push wiper mounting arm away from wiper blade assembly. To install wiper blade assembly, pull wiper mounting arm down on wiper blade until lock tab is engaged. Servicing Your Ranger...
Page 285 Replacing the wiper blades...
Page 286 If you do not take these precautions, your tires may fail or go flat. Ford Motor Company recommends obeying posted speed limits. Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components.
Page 287 Tire inspection and maintenance Inspect the tire treads, and remove stones, nails, glass or other objects that may be wedged in the tread grooves. Check for holes or cuts that may permit air to leak from the tire, and make the necessary repairs. Inspect the tire side walls for cuts, bruises and other damage.
Page 288 If your light truck has a temporary spare tire, do not include it in the tire rotation pattern. In situations where the tires differ from front to rear (snow/traction), simply rotate using a side to side pattern. Servicing Your Ranger RWARNING...
Page 289 Tire rotation pattern After each rotation, adjust individual tire pressure as specified on the Safety Compliance Certification Label. Tighten wheel lug nuts to the required torque specification and retighten again after 500 miles (800 km). If your vehicle has aluminum wheels, you may demount the full size, non-temporary spare tire (if so equipped) and remount on an aluminum wheel to rotate the spare tire into your vehicle’s rotation pattern.
Page 290 Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the decal. If you do not follow these precautions, your vehicle may not drive properly and safely. Servicing Your Ranger RWARNING...
Page 291 Ford. Ranger 4x4 P235/265 Tire and Wheel Usage Do not use P235/75R15 “All Season” tires. For Ranger 4x4 Regular Cab vehicles, P235/75R15 “All Terrain” tires are acceptable only on 15x7 inch wheels.
Page 292 Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. Servicing Your Ranger RWARNING...
Page 293 Tire identification chart RWARNING Use of aftermarket wheel assemblies may damage your vehicle or cause accidents resulting in serious injuries.
Page 294 Install tire chains on rear tires; use of chains on front tires is not recommended. Local regulations may prohibit or restrict the use of tire chains. Investigate the laws and regulations in your area before installing chains. Servicing Your Ranger RWARNING...
Page 295 Put the chains on tightly with the ends held down securely. Verify that no chain touches any wiring, brake lines, or fuel lines. Follow the chain manufacturer’s instructions. Drive slowly. If you can hear the chains rub or bang against your vehicle, stop the vehicle and tighten the chains.
Page 296 Servicing Your Ranger Battery Your vehicle may have a Motorcraft maintenance-free battery. The Motorcraft maintenance-free battery does not require additional water during its life of service. The vents are part of the cover and cannot be removed. For longer, trouble-free operation, keep the top of the battery clean and dry.
Page 297 Help Us Protect Our Environment Ford Motor Company strongly recommends that used lead-acid batteries be returned to an authorized recycling facility for disposal. Battery recycling symbol Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery.
Page 298: Automatic Transmission Fluid
(34,000 km) if under severe duty conditions. However, if the transmission is not working properly, for instance, the transmission may slip or shift slowly, or you may notice some sign of fluid leakage, the fluid level should be checked. Servicing Your Ranger RWARNING RWARNING RWARNING...
Page 299 It is preferable to check the transmission fluid level at normal operating temperature, after approximately 20 miles (30 km) of driving. However, if necessary, you can check the fluid level without having to drive 20 miles to obtain a normal operating temperature if outside temperatures are above 50˚F (10˚C).
Page 300 NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for disposing of these types of fluids. Call your local recycling center to find out about recycling automotive fluids. Automatic transmission dipstick Servicing Your Ranger...
Page 301 Remove the internal diaphragm and then add only a DOT 3 brake fluid such as Ford High Performance DOT 3 Brake Fluid, meeting Ford...
Page 302 Servicing Your Ranger Clutch fluid reservoir Driveline Universal Joint and Slip Yoke The universal joints that come standard with your vehicle do not require lubrication. If your original equipment universal joints are replaced with universal joints equipped with grease fittings, lubrication will be necessary at the intervals shown in the Maintenance Schedule and Record booklet.
Page 303: Brake Fluid
If the fluid is low, carefully clean and remove the cap from the reservoir. Fill the reservoir to the MAX line with Ford High Performance DOT 3 Brake Fluid C6AZ-19542-AA, C6AZ-19542-BA, or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A.
Page 304: Power Steering Fluid
NORMAL operating temperature range. While the engine idles, turn the steering wheel back and forth several times. Make sure that the cap assembly is installed at this time. Turn the engine off. Servicing Your Ranger RWARNING...
Page 305 Check the fluid level on the dipstick (which is highlighted in yellow in your vehicle). The fluid level should be between the arrows in the FULL HOT range, which is marked on the side of the dipstick, opposite the side marked FULL COLD. Do not add fluid if the level is within the FULL HOT range.
Page 306 FULL HOT range. Do not overfill. When you are finished, put the dipstick back in and make sure that it fits snugly. Use only power steering fluid that meets Ford specification such as MERCON Automatic Transmission Fluid (or equivalent). Servicing Your Ranger...
Page 307 If the power steering fluid is low, do not drive your vehicle for a long period of time before adding fluid. This can damage the power steering pump. If you check the power steering fluid when it is cold, make sure that the fluid reaches the FULL COLD range on the dipstick.
Page 308 Servicing Your Ranger Fuse panel (located left side of instrument panel)
Page 309 Fuses and their location...
Page 310 Servicing Your Ranger...
Page 312 40 amp - orange, 50 amp - red, 60 amp -blue. Always disconnect the battery before servicing high current fuses. Ford recommends that high current fuses be replaced by a qualified technician. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Page 313 Power distribution box Checking and Replacing Fuses If you need to check a fuse, follow these steps: Find the fuse panel, which is located in the left end of the instrument panel. The power distribution box (described earlier in this section) is found in the engine compartment, mounted on a bracket attached to the left fender apron.
Page 314 If the fuse continues to blow, have your electrical system checked. Relays Relays are devices which recieve signals from components or systems. After receiving signals, relays transfer these signals to activate or deactivate other components or systems. Servicing Your Ranger RWARNING...
Page 316 Servicing Your Ranger...
Page 317 Headlamp Bulb The headlamps on your vehicle use replaceable bulbs. When the lamp burns out, simply replace the bulb, rather than the whole lamp. Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Page 318 Turn the headlamps on and make sure that they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again. Servicing Your Ranger...
Page 319 Tail Lamp Bulb Removing the tail lamp bulb Remove the four (4) screws retaining rear lamp to vehicle. Remove rear lamp. Remove socket from lamp. Remove bulb from socket. Installing the tail lamp bulb Install tail lamp bulb in socket. Install socket to lamp.
Page 320 Servicing Your Ranger Replacing the tail lamp bulb...
Page 321 Bulb Specifications...
Page 322: Emission Control System
Avoid running out of fuel. Do not turn off the ignition while your vehicle is moving, especially at high speeds. Have the services listed in your Maintenance Schedule and Record booklet performed according to the specified schedule. Servicing Your Ranger...
Page 323 Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. On vehicles without original equipment floor covering or insulation, do not let passengers ride in your truck in a manner that allows contact between skin and the metal floor.
Page 324 Servicing Your Ranger Never use a metal exhaust collector when you service your vehicle. If the metal collector contacts any of your vehicle’s plastic trim or bumper parts they could melt or deform. Do not drive your vehicle if it does not operate properly. See your dealer if the engine runs on for more than five seconds after you shut it off or if it misfires, surges, stalls, or backfires.
Page 325 OBD II Drive Cycle The following steps must be run in the order shown. If any steps are interrupted, repeat the preceding step. Any safe driving mode is acceptable between steps. Always drive vehicle in safe manner according to traffic conditions and obey all traffic laws.
Page 326 60 mph (72-97 km/h) (manual transmissions use 5th gear). Bring the vehicle back to idle. Idle in drive (manual transmissions use 5th gear) for 40 seconds. OBD II drive cycle has been completed. Vehicle can be turned off when convenient. Servicing Your Ranger...
Page 327 Refill Capacities, Motorcraft Parts, and Lubricant Specifications...
Page 328 Servicing Your Ranger...
Page 329 Motorcraft Parts...
Page 330 Servicing Your Ranger Lubricant Specifications...
Page 332 Servicing Your Ranger...
Page 333: Vehicle Storage
Vehicle Storage Maintenance Tips If you plan on storing your vehicle for an extended period of time (60 days or more), refer to the following maintenance recommendations to ensure your vehicle stays in good operating condition. General Store all vehicles in a dry, ventilated place. Protect from sunlight, if possible.
Page 334 Ford Gas Stabilizer should be added whenever actual or expected storage periods exceed 60 days. Follow the instructions on the label. The vehicle should then be operated at idle speed to circulate the additive throughout the fuel system.
Page 335 Battery Check and recharge as necessary. Keep connections clean and covered with a light coat of grease. Brakes Make sure brakes and parking brake are fully released. Tires Maintain recommended air pressure. Miscellaneous Make sure all linkages, cables, levers and clevis pins under vehicle are covered with grease to prevent rust.
Page 347 Accessory position on the ignition... . . 41 Accessory power source, power point outlet ..Additives, engine oil ....Air bag supplemental restraint system and child safety seats .
Page 348 Audio system (see Electronic sound system) ..Autolamp system (see Headlamps) ... . Automatic transmission driving an automatic overdrive... . fluid, adding .
Page 349 Brakes (continued) fluid, checking and adding ....fluid, refill capacities ....fluid, specifications ....front disc .
Page 350 Child safety seats and air bags ..... attaching with tether straps ....automatic locking mode (retractor) .
Page 351: Index
Crankcase emission filter ....Cruise control (see Speed control) ... . . 93 Customer Assistance Centre, Ford of Canada ..Index...
Page 352 Dashboard (see Instrument panel) ... . . Daytime running light system ....Defects, reporting ....Defrost, windshield .
Page 353 Emergencies, roadside assistance ..... . battery acid spills ....fuel .
Page 354 Exhaust fumes ..... Extended Service Plan, Ford ....
Page 355 Fuel calculating fuel economy ....choosing the right fuel ....comparisons with EPA fuel economy estimates..filling your vehicle with fuel .
Page 356 Gas cap (see Fuel cap) ....Gas mileage (see Fuel economy) ..Gasoline (see Fuel) ....Gauges, Electronic engine coolant temperature gauge .
Page 357 GVWR (Gross Vehicle Weight Rating) calculating ..... definition ....driving with a heavy load .
Page 358 Identification Number, Vehicle (VIN) ..Idle relearning ....speed ......Ignition chime .
Page 359 Lamps checking ..... . combination cargo and brakelamp ... 84 daytime running light system .
Page 360 Maintenance schedule and record (see separate Maintenance Schedule and Record booklet) ..Maintenance (see Servicing) ....Manual transmission clutch ..... fluid, checking and adding.
Page 361 On-board diagnostic (OBD II) system ..Overdrive..... . . Overseas offices ....Panic alarm feature, remote entry system .
Page 362 Regulations, National Highway Traffic Safety Administration....Relays ......Remote entry system arming and disarming the anti-theft system .
Page 363 Safety restraints (continued) maintenance ..... 23 proper use ..... . replacement.
Page 364 Spare tire (continued) changing the tire ....conventional spare ....finding the spare ....removing the spare tire .
Page 365 Tailgate ......Tail lamps bulb replacement ....cleaning .
Page 366 Transfer case fluid checking ....lever operated ....Transmission automatic operation .
Page 367 Warm engine, starting ....46 Warning chimes headlamps on ..... 67 key in ignition .
Page 368 Windshield defrosting ....washing ..... . . Windshield washer fluid and wipers checking and adding fluid .
Page 369: Service Station Information
Service Station Information...

This manual is also suitable for:

1996 rangerRanger 1996Ranger 19951995 ranger

Ford Ranger Owner's Manual

Quick Links

Related Manuals for Ford Ranger

Summary of Contents for Ford Ranger

This manual is also suitable for:

Table of Contents