Selecting Bass Max Eq Mode (Maker's Setting); Adjusting And Storing/Recalling The Parametric Eq - Alpine IVA-D310 Owner's Manual

Selecting Bass Max EQ mode (Maker's
setting)
10 typical equalizer settings are preset at the factory for a variety of
musical source material.
Setting item: BASS MAX EQ
Setting contents: FLAT / ROCK / POPS / JAZZ / ELECTRIC /
HIPHOP / EASY / COUNTRY / CLASSIC /
NEWS / CUSTOM *
* Contents that are adjusted in parametric EQ.
Adjusting and Storing/Recalling the
Parametric EQ
The frequency bands of the graphic equalizer are fixed. This makes it
very difficult to correct for undesired peaks and dips at specific
frequencies. The parametric equalizer's center frequency can be tuned
to these specific frequencies. Then, the bandwidth (Q) and level are
fine-tuned, independently, to make the necessary corrections. The
parametric equalizer function is an advanced tool for serious
audiophiles.
Setting item: P-EQ
1 Touch [ ] of P-EQ.
The screen changes to the P-EQ screen to be adjusted.
2 Adjust the desired band.
P-EQ adjustment screen example
Displays the band currently selected
Displays the center frequency of the band currently
selected
Displays the band level currently selected
Displays the bandwidth (Q) of the band currently
selected
Variable range of center frequency of the band currently
selected
Active point: displays the center frequency and level
position of the band currently selected
Active bar: displayed the variable range of the band
level currently selected with an orange bar
Adjusting the Frequency
Touch [ ] or [ ], and adjust the selected band
frequency.
Center Frequency
HIGH : 10kHz, 12.5kHz, 15kHz
MID-HIGH : 500Hz, 700Hz, 1kHz, 2kHz, 4kHz, 6kHz
MID-LOW : 100Hz, 150Hz, 200Hz
LOW : 40Hz, 60Hz, 90Hz
38
-EN
Adjusting the Level
Touch [ ] or [ ], and adjust the selected band level.
Level: -12 ~ +12
Selecting the Band
The band (BAND1 through BAND4) changes each time
the [BAND] is touched.
The variable range of the active bar and the center
frequency moves according to the band.
BAND1 : LOW
BAND2 : MID-LOW
BAND3 : MID-HIGH
BAND4 : HIGH
• Touching outside the range for a selected band will move the active
bar to a band where the touched position can be adjusted.
Setting the Bandwidth
The bandwidth changes each time [Q] is touched.
HIGH : 1.0 (Bandwidth setting for HIGH is not available.)
MID-HIGH : 1.0, 2.0, 3.0
MID-LOW : 1.0, 1.5, 2.0
LOW : 1.0, 2.0, 3.0
Adjusting the Level/Frequency Directly
Move to a desired position by touching the active point and change the
setting contents. Or, move the active point to the desired position by
touching where you wish to move it.
• If you set the parametric EQ, BASS MAX EQ setting content is set to
"CUSTOM."
3 Touch [RETURN] to return to the previous screen.
Storing Adjusted Contents
The following operation is performed after Step 3 above.
4 Touch [MEMORY] on the BASS ENGINE screen.
5 Within 5 seconds, touch any one of preset buttons
[P.SET 1] through [P.SET 6].
The adjusted contents are stored on the P.SET number
you touch.
• The stored contents on the P.SET number remain undeleted despite a
following reset operation or disconnection of the battery power cord.
• Adjusted/set contents of each setting item in Bass Engine can be
stored in the preset buttons (1 through 6).
Recalling the Adjusted and Stored Contents
Following operation is performed after Step 3 above.
4 Touch any one of [P.SET 1] to [P.SET 6] on the BASS
ENGINE screen.
Recall the adjusted and stored contents.
• This function is inoperable when Defeat is set to ON.