Using The Audio Settings - Onkyo HT-R558 Instruction Manual

■
Audio TV Out
Off
On
This preference determines whether the incoming audio
signal is output from the HDMI output. You may want to
turn this preference on if your TV is connected to the
HDMI output and you want to listen to the audio from a
connected component through your TV's speakers.
Normally, this should be set to "Off".
Note
• If "On" is selected and the audio can be output from the TV, the
AV receiver will output no sound through its speakers. In this
case, "TV Speaker" appears on the AV receiver's display by
pressing DISPLAY.
• When " HDMI Ctrl (RIHD) " is set to " On
to " Auto " .
• With some TVs and input signals, no sound may be output even
" "
when this setting is set to On .
• When "Audio TV Out" or " HDMI Ctrl (RIHD)" is set to
and you're listening through your TV's speakers
turning up the AV receiver's volume control will make the sound
be output from the AV receiver's front left and right speakers. To
stop the AV receiver's speakers producing sound, change the
settings, change your TV's settings, or turn down the AV
receiver's volume.
• Listening mode cannot be changed when this setting is set to
"On" and the input source is not HDMI.
■
Audio Return Ch (ARC)
Off
Auto:
The audio signal from your TV tuner can be sent to
the HDMI OUT of the AV receiver.
The audio return channel (ARC) function allows an ARC
capable TV to send the audio stream to the HDMI OUT of
the AV receiver. To use this function, you must select the
TV/CD input selector and your TV must be ARC capable.
Note
• This setting is fixed to "- - - -" when the "HDMI Ctrl (RIHD)"
setting is set to "Off".
• This setting is set to "Auto" automatically when the "HDMI Ctrl
(RIHD)" setting is set to "On" for the first time.
" , this setting is fixed • If you set "Audio Return Ch" to "Auto", the "Audio Selector"
settings of the TV/CD input selector will be automatically
switched to "ARC"
■
LipSync
" On "
Off
(➔ page 15),
On
This function allows the AV receiver to automatically
correct any delay between the video and the audio, based
on the data from the connected monitor.
Note
• This function works only if your HDMI-compatible TV supports
HDMI Lip Sync.
After changing the settings of the
(RIHD) , HDMI Through
" "
turn off the power on all connected pieces of equipment
and then turn them on again. Refer to the user's manuals
for all connected pieces of equipment.
(➔ page 47).
" HDMI Ctrl
or
" "Audio Return Ch"
En-49
Advanced Operations

Using the Audio Settings

You can change various audio settings from the Home
(➔ page 35).
menu
1
Press RECEIVER followed by HOME.
2
Use / and ENTER to select "Audio", and then
use / / / to make the desired selection.
Note
• These settings are not available in either of the following cases:
– The "Audio TV Out" setting is set to "On"
– "HDMI Ctrl (RIHD)" is set to "On" (➔ page
listening through your TV speakers.
Tone Control
■
Bass
–10 dB to 0 dB to +10 dB in 2 dB steps
You can boost or cut low-frequency sounds output
from the front speakers.
■
Treble
–10 dB to 0 dB to +10 dB in 2 dB steps
You can boost or cut high-frequency sounds output
from the front speakers.
You can adjust the bass and treble for Speakers A and B
front speakers, except when the Direct listening mode is
selected.
Operating on the remote controller directly
1 Press RECEIVER once followed by TONE
repeatedly to select either "Bass" or "Treble".
2
Use – and + to adjust.
Tip
• Alternatively, you can use the AV receiver's TONE and –/+.
(➔ page 49).
48) and you're