Gemini GEM-P816 Installation Instructions Manual page 29

!
WI994C 3/04 Page 29
Auto Output Test on Arming
If selected (Address 0719), this will activate the Burglary Output briefly 10 seconds after the area is armed. If the alarm does not
sound, the device may be defective.
Auto-Bypass (Do not program for UL installations.); Auto-Bypass Re-entry
Zones programmed for "Auto-Bypass" (Address 0493, 0548, 0603, 0658) will be bypassed (automatically removed) if in trouble when
arming. A momentary beep will sound at the keypad to warn that the system has been armed without the protection of the auto-
bypassed zone. (Note that the exit/entry door should not be used for Auto-Bypass, otherwise the Exit/Entry Zone will be auto-
bypassed.) Note: A zone in trouble that is not programmed for "Auto-Bypass" will cause an alarm on arming after a 10-second arming
delay.
If "Auto-Bypass Re-entry" (Address 0496, 0551, 0606, 0661) is selected, securing a zone that is programmed for Auto-Bypass, while
armed, will cause that zone to re-enter the system in an armed state.
Auto Interior Bypass/Easy Exit (STAY MODE) See Interior Stay Zones
Auto-Reset; Auto-Reset After Burglary Output Timeout (Do not program for UL Installations)
If a zone detects an alarm condition and is selected for "Auto-Reset" (Address 0507, 0562, 0617, 0672), it will automatically rearm itself
as soon as the alarm condition is cleared. Auto-Reset may be delayed to occur after the Alarm Output timeout period by selecting
"Auto-Reset After Burglary Output Timeout" (Address 0719) and "Auto-Reset" . Zones that are not programmed for "Auto-Reset" will
not be capable of signaling another alarm until (a) the cause of the alarm has been corrected and (b) the control panel is disarmed.
Also see Swinger Shutdown.
Auto Status Disable
For high security Installations, the automatic scrolling of Zone Faults can be disabled. When any zone is faulted, the display will read,
"Zone Faulted".
Backup Report on Telco 1/Telco 2
If "Backup Reporting on Telco 1/Telco 2" (Address 0394) is selected and the communicator does not reach the first telephone number
(Telco 1) after three attempts, seven attempts will be made to reach the second telephone number (Telco 2). Enter Subscriber
Identification Numbers for Telephone 2 and other information required for Telephone 2. Also program Backup Report on Telco 2. Any
zone programmed to report to Telco 1 will backup report to Telco 2. Note: Subscriber Identification Numbers for both Telephones 1 and
2 must be entered, even if they are the same. Any restore will also first transmit to Telco 1 then Telco 2. The alarm and restore may not
be transmitted to the same telco telephone number.
Battery
12Vdc standby power source in the control panel is used to provide backup protection in the event of a power loss. The battery is an
integral part of the system and must be installed, even if AC power is present. Change the battery every 5 years or as required.
Burglary Output See Alarm Outputs
Call Waiting See Disable Call Waiting
Callback-Method Download; Disable Second Call Answering Machine Override (Do not program for UL Installations); Disable
Callback Download (Do not program for UL Installations); Callback Telephone Numbers; Disable Keypad Function-Mode
Download; Answer on Ring Number
Data may be downloaded remotely to the panel after a programmed number of rings (3 to 15) and a control-panel confirmation
callback. Program the "Number of Rings" (Address 1183); if not programmed, the panel will pick up after 15 rings.
The feature "2nd Call Answering Machine Override" (address 0722) allows downloading after (1) the panel detects 1 or 2 rings; (2) the
panel does not detect another ring for 8 seconds; (3) the panel detects another ring within the next 22 seconds. At this point, the panel
will connect and allow the panel to communicate with the downloading computer. In this way, the panel overrides the answering ma-
chine. The answering machine will pick up on its programmed number of rings, as usual. Note: The number of rings programmed
into the panel must exceed that of the answering machine.
Program "Disable Callback Download" (Address 0720) to prevent unauthorized downloading to an unattended panel. Program "Disable
Answering Machine Download" to inhibit downloading to a telephone connected to an answering machine. Program "Disable Function-
Mode Download" (Address 0720) to prevent downloading at the keypad.
Cancel; Cancel Code; Cancel Report to Telco 3; Cancel Window Duration (Report Cancel Window)
CANCEL is the preventing of a report from being sent by entering a user disarm code. If the area is disarmed during Entry Delay or the
"Pre-Alarm Warning", then no report will be sent and no messages will be displayed at the keypad. If the area is disarmed during the
Abort-Delay, then an "Alarm Canceled' will be displayed at the keypad and no report will be sent. If the area is disarmed during or
within the Cancel Window Duration, then an "Attempting to Cancel" will be followed by an "Alarm Canceled" for a successful
cancellation. Otherwise, the report had been sent and will be responded appropriately to by the Central Station. Cancel must be
provided with a Central Station Telephone Number, proper Subscriber O/C Report ID Numbers and a valid Cancel Code to Telco 3. A
Cancel Window ("Report Cancel Window") is the duration that the system will attempt to cancel a report, after the report is sent.
L X
NAPCO Security Systems
GEM-P816 Installation Instructions