Craftsman WEEDWACKER Incredi-Pull 316.796170 Operator's Manual page 8

WARNING: Always wear eye, hearing, foot and
body protection to reduce the risk of injury when
operating this unit.
HOLDING THE TRIMMER
Before operating the unit, stand in the operating position (Fig.
10). Check for the following:
• The operator is wearing eye protection and proper clothing
• With a slightly-bent right arm, the operator's right hand is
holding the shaft grip
• The operator's left arm is straight, the left hand holding the
assist handle
• The unit is at waist level
• The cutting attachment is parallel to the ground and easily
contacts the grass without the need to bend over
LINE REPLACEMENT
for Hassle-Free
TM
Cutting Head
Always use Craftsman Hassle-Free
TM
XTRA QUIET Spiral Line. Choose the \
line size best suited for the job at
hand. Red colored line is designed for
cutting grass and small weeds. Black
colored line is designed for cutting
larger weeds and light brush.
NOTE: Before inserting new line
into the holes in the cutting
head, identify the proper
holes. Follow directions as
shown on the line glide ._ '
plate. Do Not attempt to
remove the cutting head _ ._
from the unit when
replacing line. Fig. 10
I
WARNING: Do not remove or alter the line cutting I
blade assembly. Excessive line length will make the
clutch overheat. This may lead to serious personal
n ury or damage to the un t.
1. Remove the old line and line glide plate from the cutting
head.
Cutting Line Glide
2. Clean entire surface of cut- I-I___rl _ o_,,, Arrnw
ting head. Note positions "A"
and "B" on the cutting head.
3. Reinstall line glide plate (Fig.
11). Align arrow with:
"A" when using medium (red)
or large (black) line, or
"B" when using lines with Fig. 11
diameters smaller than
medium (red)line
NOTE: Line glide plate must Positioning
be reinstalled in Tunnel
cutting head before F_,
inserting new line.
4. Insert both ends of your
line through the proper
holes in the side of the Fig. 12
cutting head (Fig. 12).
5. Pull the line and make
sure the line is against the Line against
the hub
hub and is fully extended
through the positioning
tunnels (Fig. 13).
_Positioning
Tunnel
Fig. 13
6. Correctly installed line will be the same length on both
sides.
NOTE: Do not rest the Hassle-Free
TM
Cutting Head on the
ground while the unit is running.
Some line breakage will occur from:
• Entanglement with foreign matter
• Normal line fatigue
• Attempting to cut thick, stalky weeds
• Forcing the line into objects such as wails or fence posts
TIPS FOR BEST TRIMMING RESULTS
• For best trimming results, operate unit at full throttle.
• Keep the cutting attachment parallel to the ground.
• Do not force the cutting attachment. Allow the tip of the line
to do the cutting, especially along walls. Cutting with more
than the tip will reduce cutting efficiency and may overload
the engine.
• Cut grass over 8 inches (200 mm) by working from top to
bottom in small increments to avoid premature line wear or
engine drag.
• Cutting from right to left improves the unit's cutting
efficiency. Clippings are thrown away from the operator.
• Slowly move the trimmer into and out of the cutting area at
the desired height. Move either in a forward-backward or
side-to-side motion. Cutting shorter lengths produces the
best results.
• Trim only when grass and weeds are dry.
• The life of your cutting line is dependent upon proper
adherence of explained trimming techniques, what
vegetation is cut, and where vegetation is cut.
For example, the line will wear faster when trimming against a
foundation wall as opposed to
trimming around a tree.
DECORATIVE TRIMMING
Decorative trimming is
accomplished by removing all
vegetation around trees, posts,
fences and more.
Rotate the whole unit so that the _
cutting attachment is at a 30 ° _J, \2._
angle to the ground (Fig. 14). Fig. 14
USING THE TWIST AND EDGE
TM
FEATURE
WARNING: Before you begin using any
attachment, read and understand the manual that
came with the attachment. Follow all safety
information contained within.
I
WARNING: To avoid serious personal injury and I
damage to the unit, shut the unit off before
I
removing or installing add-ons.
You can convert this unit to edge grass.
1. Make sure the unit is turned
completely off.
2. Turn the knob counterclockwise
to loosen coupler (Fig. 15).
3. Push in the release button (Fig.
16) and twist the shaft 90 ° until
the release button snaps into the
90 ° hole (Fig. 15).
4. Turn the knob clockwise to lock
the coupler (Fig. 17).
g0° Edging Hole
(Trimmer Only)
Knob
Fig. 15